Table of Contents Set-up and Quick Use Guide ......Chapter1:Safety Instructions ......Chapter 2: Introduction ........Front and rear view of the STB ....Remote control functional key list ....Menu overview..........Chapter 3: Getting Started........ Connection..........Chapter 4: Operation.......... Program Search..........
SET-UP AND QUICK USE GUIDE Step 1: Connect AC Power Cord Plug the AC power cord into the AC outlet. Do not turn on any devices until you have finished making all necessary connections. Step 2: Antenna Connection RF IN Connect the antenna cable to the jack on the rear panel of the STB (For page 8...
Chapter 1: Safety Instructions CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS INSTALLATION AND OPERATING GUIDE AND THOSE MARKED ON THE UNIT. RETAIN THIS GUIDE FOR FUTURE REFERENCE. This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard.
Chapter 2: Introduction Front and rear view of the STB Front View Press to access the Menu Power Switch Menu navigation button in menu operation Power Indicator (LED) : Volume down/up Remote Sensor : Channel down/up Press to confirm the selection Back View Antenna Input Jack (Connect it to VHF/UHF antenna for terrestrial digital signal input)
Remote control function key list Chapter 2: Introduction You can operate every function of this STB using the buttons on the remote control handset. Below is the remote control functional key list. Press to turn ON and OFF (in standby). Press to mute the sound.
Chapter 2: Introduction Remote control functional key list Brings up the main menu. Press again to return to MENU normal viewing. Press to exit the current menu and return to previous EXIT level menu. Menu navigation buttons. ENTER Press to select the highlighted menu item or enter into sub-menu.
Page 8
Chapter 2: Introduction Remote control functional key list Switch between PIP and VCR for the secondary PIP/VCR program display. Note: For PIP output or VCR output, you can only select one output at the same time. If PIP is selected, then VCR can not be selected; If VCR is selected, then PIP can not be selected.
Menu Overview Chapter 2: Introduction Menu Overview Press MENU button to access the menu mode. Press button to select and highlight the menu item upward or downward. Press ENTER button to confirm and enter into its sub-menu. In menu operation, press to navigate in menus, press ENTER to activate the selected menu items .
Chapter 3: Getting Started Connection Connect AC power cord Do not turn on any devices until you have finished Plug the AC power cord into an AC outlet. making all necessary connections. Connecting to Antenna Follow this diagram when connecting. Antenna Rear of STB RS232...
Page 11
Chapter 3: Getting Started Connection Display Formats Overview The HD-STB Tuner offers various display formats and multiple video outputs. When the HD-STB Tuner is connected to A/V systems, the HD-STB Tuner can provide video signal formats 1080i, 720p, 576p, or 576i. 1080i, 720p and 576p modes are available for component video (YPbPr) and monitor outputs.
Page 12
Chapter 3: Getting Started Connection Connecting to a HD monitor (YPbPr type) Follow this diagram when connecting. Antenna Rear of STB RS232 YPbPr Rear of HD Ready TV Note: The YPbPr/RGB selection switch must be set to YPbPr. The component out jacks are available when HD1 (576p), HD2 (1080i), or HD3 (720p) display format is selected.
Page 13
Connection Chapter 3: Getting Started Connecting to a HD monitor (RGB type) Follow this diagram when connecting. Antenna Rear of STB RS232 YPbPr Rear of HD Ready TV Note: The YPbPr/RGB selection switch must be set to RGB. The RGB out jack is available when HD1 (576p), HD2 (1080i), or HD3 (720p) display format is selected. Important After you toggle the Display Format Selection Switch, you must turn off the STB and then turn on again, then the toggling can effect.
Page 14
Connections Chapter 3: Getting Started Connecting to a VCR Follow this diagram when connecting. Rear of STB Note: These connections are only available when VCR is selected by pressing PIP/VCR button. Rear of VCR Connecting to an Amplifier Follow this diagram when connecting. Rear of STB RS232 Amplifier...
Chapter 4: Operations Program Search You must perform the program search when using the STB at the first time. There are three ways to search programs: Quick Search, Auto Search and Manual Search. Quick Search If you live in the cities listed on the Quick Search menu, you may go ahead to select your city and start scanning all digital TV channel Signals.
SpeProgram Search/Channel & Program selection Chapter 4: Operations Manual Search If desired programs can not be searched, you can make use of Program Manual Search. Quick SRCH System Auto SRCH Password Manual SRCH Press MENU button to access the menu mode. Time Press button to select and highlight Program.
Chapter 4: Operations Channel Banner Channel Banner You can quickly check the status of current display program by pressing the DSP button. Press DSP button twice to display EPG information if available. Indicator if shows MAIN, it means current operation acts to main picture. if shows PIP, it means current operation acts to PIP sub-picture.
Chapter 4: Operations Audio Setup/Default Setting Audio Setup You can choose different audio outputs in Audio Setup menu. The STB includes standard audio mode options such as stereo or mono sound to match the broadcast signal or your home entertainment stereo system. Other audio mode options may be supported by your service provider or TV broadcaster, such as selecting alternate languages, or different commentators for sport events.
LOCK Settings Chapter 4: Operations Password setup The Rating Control lets you set up specific channels and ratings Program Rating CTRL through blocking schemes. To activate or disable all of the lock System PWD Setup Password schemes previously set up, a password is required to gain access to Clear PWD Time this menu.
Chapter 4: Operations LOCK Settings/Time Zone Selection Rating control Program Blocks programs according to the program ratings limit so Rating CTRL System PWD Setup * PG children can not view certain programs. You can set the ratings Password Clear PWD Time limit by blocking out all the programs with the ratings above a * MA...
Chapter 5: Appendix DTV Channel Table Following is the list of DTV channels available in your area. You can use it for Manual search. You can check the following list for channel number and channel frequency. City Identifier Channel & Middle Frequency Transmitter Location Start Date 1/1/2001...
Chapter 5: Appendix Troubleshooting Check the following guide for the possible cause of a problem before contacting service. Symptom Solutions No power. Plug the power cord into the wall outlet securely. Check your antenna input or location. No picture. Make sure the correct video display format is selected. If the STB is connected to your monitor or TV via VIDEO OUT jack on the back panel, the display format must be SD.
Specifications Chapter 5: Appendix PAL, DTV standard (1080i, 720p, 576p, 576i) Television System Channel Coverage Terrestrial: 6-69 ANT Input ANT Output 1 (Out to TV) 1 group, RCA type Component Video Output (YPbPr) (1080i, 720p, 576p) S-Video Output AV Output 2 groups, RCA type Digital Audio Output Coaxial, Optical...