DOSKO 620-20HE Owner's Manual

DOSKO 620-20HE Owner's Manual

Stump and root grinder
Hide thumbs Also See for 620-20HE:

Advertisement

Your Dosko grinder is intended for outdoor-use only and can be used to remove many tree stumps and
exposed root systems close to ground level. By moving the blade in sweeping movements laterally over
the top and front of the stump, you can gradually grind it away. Make sure you completely read and
understand this manual before using the grinder for the first time.
READ and UNDERSTAND this manual completely before using the grinder! Failure to properly operate,
and maintain this grinder could result in serious injury or death to the operator or bystanders.
All machines have hazards associated with their operation. This stump grinder has certain special hazards,
which you must be aware of. As an operator or owner you have a duty to be aware of these hazards and know
preventive measures to take to avoid them. When reading this manual pay particular attention to avoiding these
hazards.
In particular, be aware of the following:
Know location of buried electrical and other utility lines.
Do not allow children or untrained adults to operate.
Wear eye protection and other personal protection against flying rocks and debris.
Check that cutter wheel teeth are secured, sharp and not missing.
Do not operate if operator presence bar fails to stop engine upon release.
Make sure no children or bystanders are within 75 feet of stump grinding operation.
Protect cars, windows and other objects within 75 feet from flying debris.
Be prepared for machine "kickback" when initially contacting the stump.
Be aware of potential for carbon monoxide (CO) poisoning.
Prevent fires/explosions from fueling.
Do not attempt to perform adjustments, declog or clean unit while engine is running.
Avoid burns from engine or hot exhaust.
Avoid using in wet or icy conditions where falls may occur.
Details about these hazards are found throughout the manual and are summarized at the end of the manual under
"Important Safety Information."
ADD ENGINE OIL, FUEL & BATTERY: Your stump grinder comes fully assembled and requires only that you add
engine oil to crankcase, fuel to tank, and a battery.
INSPECT COMPONENTS: Closely inspect to make sure no components are missing or damaged. See the "Receiving
Your Unit" section for instructions on whom to contact to report missing or damaged parts.
Any Questions, Comments, Problems, or Parts Orders
Call your dealer or Dosko Customer Service 1-866-298-3659
Owner's Manual
Instructions for Operation, Maintenance
Stump and Root Grinder
337-13HC, 357-13HE, 337S-13HC
620-20HE, 620-25KE
WARNING
M2961000V.1
MODEL NUMBER: 337-13HC, 357-
SERIAL NUMBER: _____________
STOP!
1
13HE, 337S-13HC
620-20HE, 620-25KE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 620-20HE and is the answer not in the manual?

Questions and answers

Summarization of Contents

About Your Grinder
Owner/Operator/Renter Training
Essential training for safe operation and understanding of the grinder.
Rental Companies
Guidelines for rental companies regarding manual access and operator instruction.
Engine Instructions
Directs users to the engine manual for specific operation and maintenance details.
Product Suitability
Defines intended use and user liability for proper application of the grinder.
Warranty Registration
Instructions for registering the product for future updates and support.
Transporting and Receiving
Receiving Your Unit
Procedures for inspecting the grinder upon delivery for damage or missing parts.
Towing Instructions
Guidelines and safety precautions for towing the stump grinder.
Operation
Pre-start Check List & Procedures
Essential checks and procedures before starting the grinder for safe operation.
Battery Installation
Steps for installing the 12-volt battery for electric start models.
Starting the Grinder
Detailed instructions on how to safely start the grinder engine.
Stopping the Engine
Procedures for safely shutting down the engine and securing the machine.
Grinding the Stump
Step-by-step guide on how to operate the grinder for stump removal.
Refueling
Safe procedures for adding gasoline to the grinder's fuel tank.
Storing the Grinder
Proper steps for cooling, cleaning, and storing the grinder after use.
Maintenance & Repair
Perform regular maintenance
Guidelines for routine maintenance to ensure safe working condition.
Perform engine maintenance
Procedures for engine upkeep as per the engine manufacturer's manual.
Inspect fuel system / check for leaks
Regular inspection of the fuel system for any signs of leaks or damage.
Lubricate
Instructions for greasing cutter shaft and wheel bearings.
Check and adjust brake
Procedures for verifying and adjusting the braking system's functionality.
Belt Tension Adjustment
Steps to adjust belt tension and alignment for optimal performance.
Stop-Switch Adjustment
How to adjust or replace the stop switch for safety.
Setting Teeth
Instructions for installing and maintaining cutting teeth for efficiency.
Summary of Important Safety Information
General
Broad safety guidelines covering reading manuals, operator training, and environmental factors.
Prohibition Against Modifications
Warnings against altering the grinder, which can void warranty and create hazards.
Safety - Before Use
Key safety checks and preparations required before operating the grinder.
Getting Ready
Steps for preparing the work area and ensuring personal safety before grinding.
Personal protective equipment
Mandatory protective gear for safe operation.
Gasoline Safety
Critical safety measures for handling flammable gasoline.
Safety - During Use
Precautions to follow while actively operating the grinder.
Safety - After use
Procedures for safe shutdown, storage, and periodic exercise.
Safety - Inspection/Maintenance
Guidelines for regular inspection and maintenance to ensure safe operation.
Assembly Instructions
Maneuver handle over engine
Guide for positioning and securing the handle assembly to the engine.
Install handle
Steps to attach the handle using clevis pin and lock collar.
Secure wiring
Instructions for tidying and securing electrical wiring.
Mount adjustable brake lever
Process for attaching the adjustable brake lever to the handle bar.
Install air cleaner assembly (620 only)
Steps for mounting the air cleaner on specific models.

Table of Contents