1. Manuals
  2. Brands
  3. JUKA Manuals
  4. Freezer
  5. NG60G
  6. Instruction manual

JUKA NG60G Instruction Manual

Cooling and freezing upright cabinets
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NG60G and is the answer not in the manual?

Questions and answers

Related Manuals for JUKA NG60G

Summary of Contents for JUKA NG60G

  • Page 2: Table Of Contents

    COOLING AND FREEZING UPRIGHT CABINETS INSTRUCTION MANUAL Dear customers! Please read this manual thoroughly before operating the equipment! Following our instructions, you will ensure long and effective performance of the equipment. Content 1. General Information ......4 4.4.2.
  • Page 3 Dear customers! If you purchased our equipment on R290 refrigerant, please read carefully the instruction manual of the freezer. Special precautionary instruction for equipment with refrigerant R290. Fluorinated greenhouse gases are in a hermetically sealed system. Any kind of works connected with refrigeration or electric systems shall be carried out by authorized service.

  • Page 4: General Information

    Cooling Upright Cabinets: VD75G, VD70M +1ºC / +10ºC and SD70M +5ºC / -5ºC at ambient temperature +16ºC / +35ºC and relative humidity up to 75%; VD75GA +1ºC / +10ºC at ambient temperature +16ºC / +30ºC and relative humidity up to 55%;...
  • Page 5 Elements of the Construction: Picture 1. Upright Cabinet VD75G, ND75G Picture 2. Upright Cabinet SD70M, VD70M, ND70M 1. Electronic controller (temperature control). 1. Electronic controller (temperature control). 2. Cabinet control panel (switches). 2. Cabinet control panel (switches). 3. Cabinet door.
  • Page 6 Picture 3. Upright Cabinet NG60G Picture 4. Upright Cabinet VD75GA 1. Cabinet control panel (temperature control/switches). 1. Electronic controller (temperature control). 2. Cabinet door. 2. Cabinet control panel (switches). 3. Shelf support. 3. Cabinet door. 4. Grid shelf 4. Shelf support. 5.
  • Page 7 Picture 5. Upright Cabinet VG60G Picture 6. Upright Cabinet VD60G 1. Electronic controller (temperature control). 1. Electronic controller (temperature control). 2. Cabinet control panel (switches). 2. Cabinet control panel (switches). 3. Cabinet door. 3. Cabinet door. 4. Shelf support. 4. Shelf support. 5.
  • Page 8 Picture 7. Upright Cabinet ND60G Picture 8. Upright Cabinet VD140M, ND140M 1. Cabinet control panel (switches). 1. Cabinet control panel (switches). 2. Cabinet door. 2. Cabinet door. 3. Shelf support. 3. Shelf support. 4. Grid shelf 4. Grid shelf 5. Levelling supports. 5.

  • Page 9: Technical Characteristics

    2. TECHNICAL CHARACTERISTICS Technical parameters Unit. SD70M VD70M ND70M VD140M ND140M Dimensions: 2075 2075 Height Width 1412 Depth Gross volume 1284 Net volume Upright cabinet net weight Refrigerant type R452a R404a R452a R404a R452a R404a R452a R404a R452a R404a Refrigerant quantity 0,27 0,27 0,27...
  • Page 10 Technical parameters Unit. VD75G ND75G VD75GA Dimensions: 2035 2035 2100 Height Width Depth Gross volume Net volume Upright cabinet net weight Refrigerant type R452a R404a R452a R404a R290 R290 Refrigerant quantity 0,27 0,27 0,27 0,27 0,12 0,05 CO2 EQ 0,58...
  • Page 11 Technical parameters Unit. VG60G VD60G ND60G NG60G Dimensions: 1016 Height Width Depth Gross volume Net volume Upright cabinet net weight Refrigerant type R600a R290 R452a R404a R290 Refrigerant quantity 0,037 0,043 0,043 0,15 0,15 0,065 CO2 EQ 0,00 0,00 0,00 0,32 0,59 0,00...

  • Page 12: Transportation, Installation And Startup

    3. TRANSPORTATION, INSTALLATION AND STARTUP 3.1. Transportation It is forbidden to transport the equipment in any position other than vertical. During transportation, the equipment must be properly secured and packed to prevent any movement or impact inside the vehicle, protected from the weather (direct sunlight, rain, snow, etc.). Manufacturer supplies upright cabinets protected by cardboard corners and film.

  • Page 13: Connecting Electricity And Startup

    • Turn on the lighting switch (if your model is equipped with internal lighting). Picture 9. Cabinet control panel, Models Picture 10. Cabinet control panel, Model VD75GA Picture 11. Cabinet control panel, Models VD75G, ND75G 1. Main switch (turns on / off the unit). NG60G, ND60G, VD60G 1. Electronic control panel 2.

  • Page 14: Operation

    (indicated on the data plate). • To ensure proper and long-lasting operation of JUKA Upright Cabinets, please follow the recommendations indicated below: • After transporting the equipment, wait for about 2 hours before its launching •...

  • Page 15: Temperature Settings

    4.2. Temperature Settings Controller is a device used to set and maintain a desired temperature inside the upright cabinet. The manufacturer sets all necessary settings of the electronic controller for the normal operation of the unit. Before start-up, the buyer should check and, if needed, set the temperature on the electronic controller display.

  • Page 16: Electronic Controller Evco

    4.4. Electronic controller EVCO 4.4.1. Light Signals on the Electronic Controller`s Display: Diode а – Compressor: The symbol is visible during operation of the compressor. It is blinking when modification process is ongoing or in case when compressor operation is protected by security procedure. Diode b –...

  • Page 17: Electronic Controller Dixell

    4.5. Electronic controller Dixell 4.5.1. Display 1. Defrost; 2.Compressor operation; 3. Evaporator fan operation (in some models it signals condenser fan operation) 4. Temperature display. The blinking indicator value indicates a program delay. 4.5.2. Checking the set temperature. • Press the SET key (8) for a moment, then the set temperature will be shown on Picture 16 Electronic controller Dixell electronic controller the display;...

  • Page 18: Maintenance

    5. MAINTENANCE 5.1. Cleaning and Maintenance ATTENTION! All maintenance services should be carried out after the device is disconnected from the voltage! Make sure not to damage the temperature controller and other electric parts during the cleaning and maintenance of the unit. It is recommended to switch off the unit at least once a month to conduct internal cleaning, condenser maintenance, defrosting procedures and check the door seals.

  • Page 19: Door Seal

    5.1.4. Door Seal The door seal should be cleaned regularly with clean water without detergents, and then wiped dry with a soft cloth. Please make sure that the cabinet door close properly after cleaning. To check the state of the door seal place a sheet of paper between the seal and the cabinet body and close the door.
  • Page 20 • The lighting switch is on • Fluorescent lamp or the starter of the device are not burnt  Equipment does not reach the appropriate temperature, the lighting is on: Make sure that: • The main switch is turned on •...

  • Page 21: Disposal Of Equipment

    If after verifying the items described in this section the equipment does not work properly, you should contact JUKA technical service, indicating the data from the data plate of the device.
  • Page 22 ATTENTION! A warranty card is an integral part of the equipment and should always accompany the product. This warranty is a legal obligation of the seller and the service centre to undertake the responsibility to rectify defects caused by the manufacturer free of charge during the warranty period. All warranty claims should include: model number of the unit, the serial number of the cabinet, proof of purchase with the date of sale and clear seller`s stamp.
  • Page 23 Warranty card Date of sale Product and model Serial number Warranty period The buyer confirms the technical serviceability of the product/ Seller's signature ПBuyer's signature...

Table of Contents