Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Mateng EF155
Summary of Contents for Mateng EF155
- Page 2 FOREWORD The purpose of this manual is to assist you in operating and maintaining your Flail mower. Read it carefully before operating and maintaining the Flail mower, it furnishes the specifications, construction, instructions and also the maintenance. Some information may be general in nature due to unknown and varying conditions.
-
Page 3: Table Of Contents
CHAPTER Ⅴ ILLUSTRATED PARTS CATALOGUE ............15 5.1 Flail Mower Assembly (EF95-EF155) ..............15 5.2 Gearbox assembly (EF95-EF155) ................. 17 5.3 Blade Axle and Transmission Parts (EF95-EF155)..........18 5.4 Flail Mower Assembly(EF165-175) ................ 19 5.5 Gearbox assembly(EF165-175)................21 5.6 Blade Axle and Transmission Parts(EF165-175) ........... 22... -
Page 4: Chapter Ⅰ Safety Information
CHAPTER Ⅰ SAFETY INFORMATION PLEASE NOTE Make sure all potential operators of this equipment review this manual and all safety messages contained within. 1.1 Safety First Read this service manual before using the machine. This safety alert symbol indicates important safety messages in this manual. -
Page 5: Safety Signs
Pay attention to the sharp and pointed parts during repairing the machine. All protective parts shall be guaranteed to be in good state before starting the machine. Don’t leave the tractor when moving the machine; and always take away the key of the tractor with you. -
Page 6: Chapter Ⅱ Specifications
CHAPTER Ⅱ SPECIFICATIONS 2.1 Brief Introduction The series Flail mower is designed for pulverizing grass and short bramble, and shall be used in the indicated purpose. The Flail mower consists of a rotating shaft with many blades attached to it. The blades cut the grass while traveling over the working area. -
Page 7: Specifications And Parameters For Flail Mower
2.2 Specifications and Parameters for Flail Mower Model EF95 EF105 EF115 Dimensions (L×W×H) (mm) 1050×687×722 1150×687×722 1250×687×722 Structure weight (kg) Cutting width (mm) 1029 1129 Working efficiency (m 2500-7500 3000-8000 3300-9000 Input rotating speed (RPM) 6-tooth Φ35mm Rectangular spline PTO spline size... -
Page 8: Chapter Ⅲ Operation
CHAPTER Ⅲ OPERATION CAUTION: Be familiar with the machine before starting. Read this manual carefully to learn how to operate the machine safely and how to set it to provide maximum field efficiency. 3.1 Checking Before Operating ATTENTION: Only use universal joint conforming to CE standard and protect them properly. -
Page 9: Adjusting The Height
tractor. Keep the output of the tractor at 540 RPM. Before cleaning, repairing and lubricating the machine, stop the motor and take away the key with you. When the universal joint is not connected with the tractor, they must be connected again through the frame to protect the joint from damaging. -
Page 10: Regulating The Tension Of Driving Belt
3.3 Regulating the Tension of Driving Belt ATTENTION: The machine shall always stand still for regulating the tension. Remove the drivng betl cover. Loosen screws 1 2 3 4. and adjust screw 1. Tighten the screws 1 2 3 4 . Put back the driving belt cover. 3.4 Staring up Before starting the machine, control and adjust the following items: Tension of trapezoidal driving belt. - Page 11 Working Position Moving Position In order to keep the machine stable, install the supporting frame on the machine when the machine is stopped (see above drawing). ATTENTION: When transferring the moving state of the machine to the working state, do not stand between the machine and the tractor.
-
Page 12: Chapter Ⅳ Service And Maintenance
CHAPTER Ⅳ SERVICE AND MAINTENANCE 4.1 Service 4.1.1 FLUIDS AND LUBRICANTS 1. Grease: Use multi-purpose lithium based grease. 2. Gear Box Oil: Use N46 drive &hydraulic dual-purpose oil or equivalent for all operating conditions. Each Gearbox Capacity: 0.85 liter 3. Storing Lubricants: Your machine can operate at top efficiency only if clean lubricants are used. -
Page 13: Maintenance
4.2 Maintenance ATTENTION: All maintenance, repairing, cleaning and lubricating shall be conducted when the tractor and motor are stopped and the key is taken away. By following a careful service and maintenance program for your machine, you will enjoy many years of trouble-free operation. The period recommended is based on normal operating conditions. -
Page 14: Storage
4.2.3 ANNUALLY MAINTENANCE Cleaning mud and grass on the machine thoroughly. Check all clearance between bearings and gears if you have replaced them. Please run it without load for 3-5 minutes. Check and clean blade axles. Replace oil seals and press butter into them. Check all blades, replace then if they are wear-out or damaged. -
Page 15: Operation After Storage
4.4 Operation After Storage Before the machine is started up, check the following items regularly: Check oil level and add it if not enough. Check and tighten all screws and nuts; Check the regulated state of the machine. Check the blade state. Check the air hole on the gearbox. -
Page 16: Chapter Ⅴ Illustrated Parts Catalogue
Always give your dealer the Model of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part. 5.1 Flail Mower Assembly (EF95-EF155) - Page 17 Flail Mower Assembly Ser.No Part No Name and Specification Quantity Remarks SL100.00.023 Hanging Plate (left) SL100.00.024 Mud shield SL100.00.025 roller SL100.00.165 Copper sheath SL100.01.001 Gearbox SL100.00.101 Rear fender SL100.00.115 Guard shade GB 5783-86 Hex.head bolt M10×60 SL100.00.112 Guard cover SL100.00.015 Gearbox seat SL100.00.022 Hanging plate(right)
-
Page 18: Gearbox Assembly (Ef95-Ef155)
5.2 Gearbox assembly (EF95-EF155) Gearbox Assembly Ser.No Part No Name and Specification Quantity Remarks GB 5783-86 Hex. head bolt M8×30 GB 93-87 Spring lock washer 8 SL100.01.107 Bearing cover SL100.01.108 Paper gasket GB 13871-94 Oil seal 35×50×8 GB/T 276-94 Bearing 6207 SL100.01.109... -
Page 19: Blade Axle And Transmission Parts (Ef95-Ef155)
5.3 Blade Axle and Transmission Parts (EF95-EF155) Blade Axle and Transmission Parts Ser.No Part No Name and Specification Quantity Remarks GB1096-79 Key 10×30 SL100.00.113 Transmission shaft UC205-Z Bearing with flange 90207 Grease nipple M8 GB 93-87 Spring lock washer 8 GB 5783-86 Hex. -
Page 20: Flail Mower Assembly(Ef165-175)
5.4 Flail Mower Assembly(EF165-175) Ser. No. Part No Name and Specification Quantity Remarks EF175-0006 Gearbox EF175-1023 Shaft Sleeve EF175-1022 Shaft DIN 6885 Key 10*65 GB13912 Hex. head bolt M8*35 GB93-87 Spring lock washer 8 EF175-0004 Shaft tube GB5783-86 Hex. head bolt M12*30 GB848 Washer 12 GB982... - Page 21 Ser. No. Part No Name and Specification Quantity Remarks EF175-1025 Belt wheel (little) EF175-0005 Belt cover GB5783-86 Hex. head bolt M12*40 GB93-87 Spring locked washer 12 GB934 Hex. head bolt M16(1.5)*65 GB934 Hex. nut M16*1.5 EF175-0001 Blade axle cover EF175-0016 Bracket EF175-0013 Suspension plate (left)
-
Page 22: Gearbox Assembly(Ef165-175)
5.5 Gearbox assembly(EF165-175) Ser. No. Part No Name and Specification Quantity Remarks EF175-2001 Gear box EF175-2002 Bevel gear EF175-2003 Adjusting shim UC6007 Bearing 6007 GB893-86 Blocked patch 42 EF175-2004 Input shaft EF175-2005 EF175-2006 Cover Oil seal 35*80*8 GB5783-86 Hex. head bolt M12*35 EF175-2007 Adjusting shim EF175-2004... -
Page 23: Blade Axle And Transmission Parts(Ef165-175)
1 7 * 9 9 1 1 7 * 9 9 1...
Need help?
Do you have a question about the EF155 and is the answer not in the manual?
Questions and answers