Advertisement
Quick Links
Advertisement
Related Manuals for CALOR IT3440C0
Summarization of Contents
1. ASSEMBLY - POLE SETUP
Insert Pole and Lock
Insert the pole into the unit base until it clicks and secure the pole locks.
Extend and Lock Pole
Pull pole sections to full height and secure the three locks.
1. ASSEMBLY - ATTACHMENTS
Attach Hanger and Steam Head
Secure the hanger to the pole and position the steam head on its cradle.
Connect Steam Hose and Support
Connect the steam hose securely and attach the vertical support with hanger.
2. BEFORE USE - PREPARATION
Prepare Garment Support
Unwind and adjust the garment support tension, then lock it.
Water Tank Filling
Remove, fill with water, and securely re-attach the water tank.
3. ACCESSORIES - USAGE AND SAFETY
Hanging Garments on Hanger
Hang your garment onto the provided hanger for steaming.
Accessory Installation Safety
Ensure the appliance is off and cool before attaching accessories.
Fabric Brush Functionality
Use the fabric brush to enhance steam penetration into fabric weaves.
4. USE - OPERATION
Correct Appliance Placement
Operate the appliance only on a stable, horizontal surface.
Power Connection and Activation
Plug the appliance into power and turn it on, adjusting steam output.
Steam Generation Time
Wait approximately 45 seconds after activation for steam production.
5. DURING USE - TECHNIQUES AND SAFETY
Optimal Steaming Technique
Direct steam downwards over garments for the best results.
Safety: Avoid Direct Steam
Never aim the steam jet directly at people or pets.
Troubleshooting: Low Steam Output
If steam is weak or stops, check the water level in the reservoir.
6. AFTER USE - SHUTDOWN
Turn Off and Unplug Appliance
Switch the appliance off using the ON/OFF button and disconnect the power cord.
Prepare Water Tank for Refill
Remove the water tank and prepare it for refilling.
6. AFTER USE - CONTINUED PREPARATION
Refill Water Tank
Open the water tank, refill it with water, and re-cap it.
Re-attach Water Tank
Securely close the water tank cap and reinsert the tank into the unit.
6. AFTER USE - STORAGE
Empty and Clean Water Tank
Unscrew the water tank cap, empty all water into a sink, and re-secure the cap.
Store Power Cord
Roll up the power cord neatly and attach it to its designated hook.
Allow Appliance to Cool
Let the appliance cool down completely for one hour before storing it.
7. DESCALING PROCEDURE - INTRODUCTION AND PREPARATION
Descaling Schedule and Safety
Descale every 6 months or if performance drops; ensure appliance is cool.
Disassemble for Descaling
Remove steam head, unlock and collapse pole, and detach water tank.
7. DESCALING PROCEDURE - DESCALING STEPS
Add Descaling Water
Pour 0.5 liters of water into the appliance's tank inlet.
Agitate and Unscrew Cap
Gently shake the unit and unscrew the anti-calc cap over a sink.
7. DESCALING PROCEDURE - COMPLETION
Drain Descaling Mixture
Tilt the appliance to empty the water into a sink.
Reassemble and Refill Tank
Re-lock the pole, position the steam head, and refill the water tank.
7. DESCALING PROCEDURE - FINAL RINSE
Rinse Cycle Operation
Reassemble, plug in, and run the appliance until the water tank is empty for a rinse.
8. CLEANING - BASIC CLEANING
Allow Appliance to Cool
Allow the appliance to cool completely for one hour before cleaning.
Clean Base with Damp Sponge
Clean the appliance base using only a damp sponge and water.
Clean Steam Head with Damp Sponge
Clean the steam head using only a damp sponge and water.
8. CLEANING - IMPORTANT PRECAUTIONS
Avoid Detergents and Direct Washing
Never use detergents and avoid washing or rinsing the unit or steam head directly under a sink.
Need help?
Do you have a question about the IT3440C0 and is the answer not in the manual?
Questions and answers