Related Manuals for Et ET-M672BH WB Series
Summary of Contents for Et ET-M672BH WB Series
- Page 1 INSTALLATION MANUAL ET Solar Series Module Installation | Safety instructions | Maintenance...
- Page 2 www.etsolar.hk Version:2021Q1...
-
Page 3: Table Of Contents
6.2 The visual inspection of the modules ............- 9 - 6.3 Inspection of the connector and cable ............- 9 - Disclaimer of liability ....................... - 9 - Appendix 1: Electrical ratings of ET Solar modules ............. - 10 -... -
Page 4: Introduction
European Code and other countries Code be followed. Non-compliance with this installation instruction may result in property damage and/or physical injury. ET Solar will not be liable for compensation of any loss or injury caused by this type of non-compliance. 2 Codes and regulations... -
Page 5: Safety Precautions For Installing A Solar Photovoltaic System
+85℃. If modules are to be installed in areas where the temperature may go outside the above range, please consult with ET Solar before installation. Do not attempt to disassemble the module, and do not remove any attached nameplates or components. Doing so will void the warranty. -
Page 6: General Installation Notes
www.etsolar.hk Do not wear metallic rings, watchbands, ear, nose, or lip rings or other metallic devices while installing or troubleshooting photovoltaic systems. Use appropriate safety equipment (insulated tools, insulating gloves, etc.) approved for use on electrical installations. Observe the instructions and safety precautions for all other components used ... -
Page 7: Mechanical Installation
4 Mechanical Installation 4.1 Installation requirement ET Solar bears NO responsibility for any damage caused by the use of unsuitable or inappropriate mounting / fixing systems. Before starting with the mounting process, the strength of mounting / fixing structure on the panel field must meet the local loading condition, e.g. -
Page 8: Mounting With Bolts
www.etsolar.hk Mounting with bolts 4.2.1 4 or 8 pre-drilled mounting holes, located on the aluminum alloy frame, are provided for ease of installation. They are designed to be used with metric M8 stainless steel screws. We recommend to use a tighten torque of 16~20 The module must be attached and supported by at least four bolts through the ... -
Page 9: Installation Position And Static Loads
www.etsolar.hk Installation position and static loads 4.2.3 - 6 -... -
Page 10: Electrical Installation
PV system connectors with suitable cable which are qualified for EN50618(or IEC62852 ) All field wiring cables must have large enough cross- sectional areas approved for use at the maximum short-circuit current of the PV module. ET Solar recommends that installers use only sunlight resistant cables - 7 -... -
Page 11: Connectors
ET Solar); 5.4 Bypass Diodes ET Solar module junction boxes contain bypass diode which is parallel connection with the PV cell strings. if hot spot occurred, the diode will come into operation to stop the main current from flowing through the hot spot cells in order to prevent module over-heated and performance loss. -
Page 12: Cleaning
If a module power decreases abnormally, and its glass surface is found covered by dust, please contact your module installer, retailer or ET solar immediately for technical support. Do not attempt to clean a module if the glass is broken. -
Page 13: Appendix 1: Electrical Ratings Of Et Solar Modules
PV product. No license is granted by implication or otherwise under any patent or patent rights. The information in this manual is based on ET Solar's knowledge and experience and is believed to be reliable, but such information including product specification (without limitations) and suggestions does not constitute a warranty, expressed or implied. - Page 14 www.etsolar.hk Sheet 2: solar cell type:158.75mm - 11 -...
- Page 15 www.etsolar.hk Sheet 3: solar cell type:156.75mm mono-si &poly-si Sheet 4: solar cell type:182mm For module specifications or datasheets, please download from: www.etsolar.hk - 12 -...
- Page 16 MANUFACTURE INFORMATION: ET SOLAR POWER HONGKONG LIMITED Room 01,21/F,XINGFA Commercial Building,9th Tobacco Factory Street,Mong Kok, HongKong. Tel: 86 510 85382358 Fax: 86 510 85382358 Mail: support@etsolar.hk www.etsolar.hk ET SOLAR INC. 4900 Hopyard Road,Suite 310,Pleasanton,CA 94588,USA E-mail: sales@etsolar.us - 13 -...
Need help?
Do you have a question about the ET-M672BH WB Series and is the answer not in the manual?
Questions and answers