Table of Contents
Advertisement
Quick Links
INSTALLATION, OPERATION & MAINTENANCE MANUAL
PSP125ABK / PSP200SSK
TOP DISCHARGE
Electric Submersible Pumps
Single Phase
115V
Read this manual carefully before installing, operating or servicing these pump models.
Observe all safety information. Failure to comply with instructions may result in personal
injury and/or property damage. Please retain these instructions.
KOD PSPK rev 01
Advertisement
Table of Contents
Related Manuals for Kodiak PSP200SSK
Summary of Contents for Kodiak PSP200SSK
- Page 1 INSTALLATION, OPERATION & MAINTENANCE MANUAL PSP125ABK / PSP200SSK TOP DISCHARGE Electric Submersible Pumps Single Phase 115V Read this manual carefully before installing, operating or servicing these pump models. Observe all safety information. Failure to comply with instructions may result in personal injury and/or property damage.
-
Page 2: Table Of Contents
SERVICING YOUR SUBMERSIBLE PUMP......................13 MAINTAINING YOUR PUMP ..........................14 CHANGING SEAL OIL ............................14 DIMENSIONAL DRAWING ............................. 15 MODEL: PSP125ABK CURVE ..........................16 MODEL: PSP200SSK CURVE ..........................16 EXPLODED VIEW OF PWP125ABK ........................... 17 EXPLODED VIEW OF PSP200SSK ..........................18 PSP SERIES PARTS LIST ............................ -
Page 3: Introduction
INTRODUCTION This Installation, Operation and Maintenance manual provides important information on safety and the proper inspection, disassembly, assembly and testing of the Kodiak Power submersible pump. This manual also contains information to optimize performance and longevity of your Kodiak Power submersible pump. -
Page 4: Safety
SAFETY Pump installations are seldom identical. Each installation and application can vary due to many different factors. It is the owner/service mechanics responsibility to repair, service, and test to ensure that the pump integrity is not compromised according to this manual. -
Page 5: Inspection
INSPECTION Review all safety information before servicing pump. The following are recommended installation practices/procedures for the pump. If there are questions in regards to your specific application, contact your local Kodiak Power distributor, or John Brooks Company Limited. PRE-INSTALLATION INSPECTION 1) Check the pump for damage that may have occurred during shipment. -
Page 6: Pump Installation
Proper lifting equipment (rope/chain) must be used. POSITIONING THE PUMP Kodiak Power, PSP Series pumps are designed to operate fully or partially submerged. Avoid running the pump dry for extended periods of time. Refer to data sheet for minimum submersion depth for your particular model. As a general rule, PSP Series top discharge pumps can pump down to a level above the suction screen. -
Page 7: Pump Rotation
PUMP ROTATION Two ways to check the correct pump rotation: 1. By looking at the impeller; the rotation of the impeller should be counter clockwise as shown in the picture below. 2. By looking from the top of the pump. Since the impeller cannot be seen, the best way to check the rotation is to check the kick back motion of the pump when the pump just starts. -
Page 8: Pump Operation
TYPICAL MANUAL DEWATERING INSTALLATION NOTE: Maximum recommended starts should not exceed 10 times per hour. Models PSP125ABK, PSP200SSK are provided with a 33’ (10 m) power cord. NEVER splice the power cable due to safety and warranty considerations. Always keep the plug end dry. -
Page 9: Stopping
STOPPING To stop the pump (manual and automatic mode), unplug it from the power source, turn off the breaker, or turn the power source off (generator). TYPICAL AUTOMATIC DEWATERING INSTALLATION NOTE: Maximum recommended starts should not exceed 10 times per hour. AUTOMATIC OPERATION Float switches (wired into the pump motor or piggy-back style) are available from the factory as an option. -
Page 10: Stopping
Use with approved motor control that matches motor input in full load amperes. “UTILLISER UN DÉMARREAR APPROUVÉ CONVENANT AU COURANT Á PLEINE CHARGE DU MOTEUR.” Kodiak Power has been evaluated for use with water or water based solutions. Please contact the manufacturer for additional information. -
Page 11: Single Phase Wiring Instructions
SINGLE PHASE WIRING INSTRUCTIONS FOR YOUR PROTECTION, ALWAYS DISCONNECT PUMP FROM ITS POWER SOURCE BEFORE HANDLING. Single phase pumps are supplied with a three prong grounded plug to help protect you against the possibility of electrical shock. DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE GROUND PIN. The three prong plug must be inserted into a mating three prong grounded receptacle. -
Page 12: Trouble Shooting
SERVICING YOUR SUBMERSIBLE PUMP Pump should be disconnected from the electric power supply before proceeding to do any service or maintenance. To service or repair your pump, please contact your local Kodiak Power distributor. Service should only be performed by a qualified electrician. -
Page 13: Maintaining Your Pump
MAINTAINING YOUR PUMP • Pump should be disconnected from the electric power supply before proceeding to do any service or maintenance. • Pump should be inspected at regular intervals. • More frequent inspections are required if the pump is used in a harsh environment. -
Page 14: Dimensional Drawing
DIMENSIONAL DRAWING Model PSP125ABK 1.0” 9.0” 5.5” PSP200SSK 2.0” 14.6” 6.5”... -
Page 15: Model: Psp125Abk Curve
MODEL: PSP125ABK CURVE MODEL: PSP200SSK CURVE... -
Page 16: Exploded View Of Pwp125Abk
EXPLODED VIEW OF PSP125ABK... -
Page 17: Exploded View Of Psp200Ssk
EXPLODED VIEW OF PSP200SSK... -
Page 18: Psp Series Parts List
PSP SERIES PARTS LIST Pump Model PSP125ABK PSP200SSK Pos. No. Part Description Item # Item # Strainer 201980 201967 Impeller nut 202890 Impeller, Cast Iron 202055 Impeller, Fiberglass Reinf. Plastic 202920 Pump Housing/Suction Cover 202155 202195 07-1 O-Ring (Kit Only) -
Page 19: Single Phase Wiring Diagram 115V (Psp125Ssk / Psp200Ssk)
SINGLE PHASE WIRING DIAGRAM 115V (PSP125ABK / PSP200SSK) -
Page 20: Warranty And Limitation Of Liability
Brooks Company Limited warrants for a period of one (1) year, that all products or parts thereof furnished by John Brooks Company Limited under the brand name Kodiak Power, hereinafter referred to as the “Product” are free from defects in materials and workmanship and conform to the applicable specification. -
Page 21: Notes
NOTES: Distributed by : Multi Pression L.C. inc. 1551, De Coulomb Street, suite 110, Boucherville, Quebec J4B 8J7 Phone : 1.866.641.6633 Fax : 450.641.2633 www.multipsi.com...
Need help?
Do you have a question about the PSP200SSK and is the answer not in the manual?
Questions and answers