Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ROXX E.SHOW D
Summary of Contents for ROXX E.SHOW D
- Page 1 User Manual E.SHOW T/D USER MANUAL...
-
Page 2: Table Of Contents
1.1. General Preventive Measures 1.2. Regulations for equipment that connects to power mains 1.3. Technical warnsigns and explanation 2. Introduction 2.1. About us 2.2. E.SHOW T/D 3. General Product Information 3.1. Scope of delivery 3.2. Control Functions 3.3. Features 4. Installation & Setup 4.1 Physical Installation and Rigging... - Page 3 User Manual 7. Technical Data / Diagrams 7.1 Technical drawings and measurements 7.2 IP Rating 7.3 Technical Data 7.4 DMX-Charts 7.5 RDM Templates 8. Troubleshooting 9. Manufacturer´s Declaration...
-
Page 4: Safety Informations
1.1.1. Please read, understand and follow the instructions. 1.1.2. Store the instructions and information in a safe place. Best solution is the ring binder provided by ROXX. 1.1.3. Follow all safety warnings. Under no circumstances remove safety warnings or other information from the equipment. -
Page 5: Regulations For Equipment That Connects To Power Mains
User Manual 1.1.20. Observe all disposal laws applicable in your country. Especially for the packaging. 1.1.21. Plastic bags are not a toy! Keep away from children! 1.1.22. Please note that changes or modifications which are not approved by the party responsible for compliance will void the user’s authority to operate the device. -
Page 6: Technical Warnsigns And Explanation
User Manual 1.3. Technical warnsigns and explanation In order to prevent the risk of an electric shock, under no circumstances remove the cover/back or open the unit in any way! No user serviceable parts are inside. Service, maintenance and repairs should only be done by qualified service personnel or the manufacturer. -
Page 7: Introduction
Each one reaching an exceptionally good light quality with high CRI / TLCI and a massive light luminosity. The E.SHOW T- and D-Versions both impress with their homogeneous light and their enormous output. The E.SHOW T (Tungsten) produces high quality white light with 3.200 Kelvin and 11.000lm. The E.SHOW D (Daylight) convinces with an 13.500lm luminous flux @ 5.600 Kelvin. -
Page 8: General Product Information
3.2. Control Functions • 1/2/4CH Mode, 3CH Strobe Mode • Stand Alone Quick Light Function with Timer • Master & Slave (by DMX and Wireless DMX) ® • Wireless DMX (Lumenradio CRMX • ROXX App - Bluetooth 5.0 3.3. Features... -
Page 9: Installation & Setup
Please take care that supporting surfaces are loadable and stable. Hanging: On the bottom the yoke provides 2 Camlock QuickRelease connectors. Here it´s possible to click in the ROXX Omega Bracket ST (optional accessory) equiped with any suitable clamp. Open... -
Page 10: Connections
Manual Pendant Light*: The sophisticated and attractive design of the ROXX E.SHOW T/D makes the luminaire predestinated for the use as a pendant light, e.g. for exhibition booths, galas,… The position of the safety eyelet and the lamp body balancing makes that possible in a perfect way. -
Page 11: Ac Power
Manual 4.2.1. AC Power The E.SHOW T/D operates on any 100–260 V, 50/60 Hz AC mains power supply with a maximum power consump- tion of 220W. Connect the fixture to AC power using the supplied cable or a similar one with Neutrik powerCON TRUE1 NAC3FX-W or a compatible type, to ensure the correct ingress protection (IP). -
Page 12: Wireless Connection
DMX Settings. E.SHOW T/D can act as a fully operative CRMX Receiver and be paired to an active wireless transmitter (CRMX) simultanously as being connected to a cabled DMX. The device will prioritize cabled DMX input over wireless DMX and over Bluetooth. - Page 13 User Manual 4.2.2.2. Wireless Connection CRMX Enabled • CRMX(TX) The indicator infront of "CRMX Operation Mode (TX)" shows that the fixture is now working in wireless DMX 4 CH Linked transmit mode. Receive Reset Next "(TX)"= CRMX operating mode Disconnect (5 ) is set to transmit BLE (Bluetooth)
- Page 14 BLE (Bluetooth) Enabled + Paired DMX). CRMX Enabled CRMX(TX) Operation Mode No indicator infront of "BLE", 4 CH Linked fixture is not paired to ROXX Receive Reset App. Next Disconnect ( 5 ) BLE (Bluetooth) Enabled, not paired Enabled CRMX...
-
Page 15: Operation
Once the fixture is connected to AC power, the boot process starts and the following information will appear on the display: “Ready to ROXX”, the product name and the current software version. After this process, the fixture is ready for operation, and starts in the previous- ly enabled mode. - Page 16 User Manual Display Off Pressing ESC + arrow down simultaneously the display backlight function will set to off and the display will turn off immediately. Once a control is pressed the display backlight will turn on. BLE enabled / disabled Pressing ESC + Arrow Up simultaneously the Bluetooth will enabled or disabled.
-
Page 17: Configuration
User Manual 5.4 Configuration Home Screen After boot process the fixture is ready for operation and starts in the previously enabled mode. At home screen the following information will appear, depending on the current operating mode: DMX Adress Operating Mode (DMX Mode, Quick Light or Standalone Mode) Next available DMX address depending on the fixtures DMX footprint External Data protocol (CRMX, DMX, BLE). -
Page 18: Stand Alone
User Manual Level 1 Level 2 Menu DMX Mode DMX Mode 1CH - 8bit Stand Alone 2CH - 16bit Slave 3CH Strobe - 8bit Settings 4CH - 16bit (default) System Info 5.4.3 Stand Alone* Press ENTER to access to main menu (level 1). While using the UP / DOWN arrows, please select the menu item “Stand Alone”... -
Page 19: Slave Mode
User Manual To select “Timer” please press ENTER to access to main menu (level 1). While using the UP / DOWN arrows, please select the menu item “Stand Alone” and confirm by pressing ENTER. Select the item menu “Timer” by using the up/down controls and press ENTER. Now you can activate / deactivate the Timer function, select “Fade In”, “Dwell Time”... - Page 20 User Manual Main Menu Menu level 2 Menu level 3 Menu level 4 Description CRMX <on/off> On=CRMX enabled / Off= CRMX disabled Receive= CRMX module as Receiver Operating Mode <receive/transmit> Transmit= CRMX module as Transmitter Yes= pair with CRMX devices. CRMX must be activated on all devices and the pairing must be Transmit Link <no/yes>...
- Page 21 User Manual Main Menu Menu level 2 Menu level 3 Menu level 4 Description The LED responds abruptly to it´s DMX values Dimmer Response The LED responds similar to a halogen fixture Halogen with soft changes at brightness. 800 Hz 1200 Hz 2000 Hz LED Frequency...
-
Page 22: System Info
Main Menu Menu level 2 Menu level 3 Menu level 4 Display installed firmware version Firmware Version vx.xx 101xxxxxxxx (E.SHOW T) Serial Number 100xxxxxxxx (E.SHOW D) 0X6a6a0101xxxx (E.SHOW T) Display unique RDM ID for identification RDM UID 0X6a6a0100xxxx (E.SHOW D) -
Page 23: Accessories
User Manual 6. ACCESSORIES 6.1 Lenses Available lenses for ROXX E.SHOW black with order numbers: Narrow Medium Wide Elliptical Narrow Elliptical Wide Art.: 11207001 Art.: 11207101 Art.: 11207201 Art.: 11207301 Art.: 11208201 Lens matrix: SHOW TW+ SHOW FC SHOW T... -
Page 24: More Accessories
User Manual 6.2 More accessories Accessory Holder 8-way barndoor Gel-frame Honey comb Art.: 11907401 Art.: 11907501 Art.: 11907701 Art.: 11907601 Omega Bracket ST Softbox by DoPchoice Snapgrid by DoPchoice Full anti-glare shield Art.: 90900002 Art.: 11908301 Art.: 11908301 Art.: 11208401 Touring case 8 Art.: 11908001... -
Page 25: Technical Data / Diagrams
User Manual 7. TECHNICAL DATA / DIAGRAMS 7.1 Technical drawings and measurements... -
Page 26: Ip Rating
Manual 7.2 IP Rating ROXX products conform to officially classified IP standard levels. E.SHOW T/D is rated to IP65 when using the covers for the housing parts. IP stands for Ingress Protection and IP65, according to classified standard, means shielded against dust and high-pressure jets of water from any side. -
Page 27: Technical Data
5.600K (E.SHOW D) 49,87 lm/W (E.SHOW T) Efficancy (max) 61,55 lm/W (E.SHOW D) CRI/RA TLCI Rf 95 / Rg 102 (E.SHOW T) TM-30-15 Rf 94 / Rg 103 (E.SHOW D) 10.743lm (E.SHOW T) Luminous flux 13.222lm (E.SHOW D) 1.664 lx (E.SHOW T) illuminance Lux @ 5m (narrow lens) 1.989 lx (E.SHOW D) - Page 28 User Manual 7.3 Technical Data Electrical Data AC power, max. 90 – 285V 50/60Hz AC Power, nominal 100 – 260V 50/60Hz Electrical Protection Overload protection with automatic recover Max Inrush Current Max power consumption 220W Typical power consumption 160W Standby power 6,7W Max power thru @ 100 V Max power thru @ 230 V...
-
Page 29: Dmx-Charts
DMX CHART 7.4 DMX-Charts 1 CH Mode - 8bit 3 CH Strobe Mode - 8bit 2 CH Mode - 16bit 4 CH Mode - 16bit / Default Mode 1 CH MODE - 8bit Function Value Setting Dimmer 000-255 0 - 100% 2 CH MODE - 16bit Function Value... - Page 30 DMX CHART 4 CH MODE - 16bit / Default Mode Function Value Setting Dimmer 000-255 0 - 100% Dimmer-fine 000-255 0 - 100% 000 - 019 Shutter close 020 - 024 Shutter open 025 - 064 Strobe 1 (fast slow) 065 - 069 Shutter open 070 - 084...
- Page 31 DMX CHART 110-114 LED Frequency 3600Hz (hold 3s) 115-119 LED Frequency 12kHz (hold 3s) 120-124 LED Frequency 25kHz (hold 3s) 125-129 No function 130-134 Fan Auto (hold 3s) 135-139 Fan Silent (hold 3s) Device Settings 140-144 Fan Studio (hold 3s) 145-149 Fan Off (hold 3s) 150-154...
-
Page 32: Rdm Templates
0100 xxxx (E.SHOW D) * Note: During RDM identifying process E.SHOW T/D flashes white 100% to 50% alternately. RDM functions For easy identifying ROXX E.SHOW T/D during RDM process the unit will jump from white 100% to 50% color every second. Function... -
Page 33: Troubleshooting
Bluetooth is disabled at your mobile Please eanble Bluetooth at your mobile device device settings. Please use same Bluetooth Pin to connect ROXX. APP with the fixture. Current BLE Pin can be read Mobile device has wrong Bluetooth Pin out inside fixture´s wireless DMX settings. -
Page 34: Manufacturer´s Declaration
ROXX GmbH, Hansestr. 91, 51149 Köln Email: info@roxxlight.com or the ROXX authorized reseller in your country, from where you purchased your product. Correct Disposal of this product This is for the European Union and European countries with electrical waste collection systems. When this label is shown on the product or brochure it means that the item cannot be disposed with household waste. - Page 35 User Manual CE Compliance The equipment marketed by ROXX GmbH complies (where applicable) with the essential requirements and other specifications of the following Directives: • 2014/53/EU (RED) • 2014/30/EU (EMC) • 2014/35/EU (LVD) • 2011/65/EU (RoHS) The complete EU- and UK-Declaration of Conformity can be found at www.roxxlight.com/support, or you can also request it at info@roxxlight.com...
Need help?
Do you have a question about the E.SHOW D and is the answer not in the manual?
Questions and answers