Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Desa ReDDY HeaTeR RV125EDI
Summary of Contents for Desa ReDDY HeaTeR RV125EDI
- Page 1 DDY H PORTABLE FORCED AIR HEATER OWNER’S MANUAL 125 SIDE PFA/PV 004 Model RV125EDI IMPORTANT Read and understand this manual before assembling, starting or servicing heater. Improper use of heater can cause serious injury. Keep this manual for future reference.
-
Page 2: Table Of Contents
CONTENTS SECTION Safety Information ... 3 Introduction ... 4 Product Identification ... 4 Unpacking ... 4 Assembly ... 5 Theory of Operation ... 6 Fuels ... 6 Ventilation ... 7 Operation ... 7 Storage ... 8 Preventative Maintenance Schedule ... 8 Troubleshooting ... -
Page 3: Safety Information
SAFETY INFORMATION IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock, and carbon monoxide poisoning. Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, and/or nausea. -
Page 4: Introduction
Outlet Lower Shell Fuel Cap Figure 1 - RV125EDI 1. Remove all packing items applied to heater for shipment. 2. Remove all items from carton. 3. Check items for shipping damage. If heater is damaged, promptly inform dealer where you bought heater. -
Page 5: Assembly
ASSEMBLY This heater is furnished with wheels, handles, and an interrupter. These items and the mounting hardware are found in the shipping carton. Tools Needed • Medium Phillips Screwdriver • 3/8" Open or Adjustable Wrench • Hammer 1. Slide axle through wheel support frame. Install wheels on axle. IMPORTANT: When installing wheels, point extended hub of wheels toward wheel support frame (see Figure 2). -
Page 6: Theory Of Operation
THEORY OF OPERATION Clean Heated Air Out FUELS The Fuel System: The air pump forces air through the air line. The air is then pushed through the burner head nozzle. This air causes fuel to lift from the tank. A fine mist of fuel is sprayed into the combustion chamber. The Air System: The motor turns the fan. -
Page 7: Ventilation
VENTILATION A standard 4 inch (10.16 cm) draft regulator is required only if total vertical and horizontal length of the vent pipe exceeds 20 feet (6.1 meters). Regulator, vent pipe, and fittings are not supplied with the heater. Purchase these items at a local hardware store. -
Page 8: Storage
OPERATION Continued STORAGE PREVENTATIVE MAINTENANCE SCHEDULE To Stop Heater 1. Unplug power cord from outlet. To Restart Heater 1. Wait 2 minutes after stopping heater. 2. Repeat steps under To Start Heater, page 7. 1. Drain fuel tank. Locate drain plug on underside of fuel tank. Remove drain plug to drain all fuel. -
Page 9: Troubleshooting
TROUBLE- SHOOTING Never service heater while it is plugged in, operating, or hot. Severe burns and electrical shock can occur. OBSERVED FAULT Heater ignites, but flame-out control shuts off heater after a short period of time. Heater will not ignite, but motor runs for a short period of time. -
Page 10: Service Procedures
SERVICE PROCEDURES Upper Shell Removal 1. Remove screws along each side of heater using 5/16" nut-driver. These screws attach upper and lower shells together. 2. Lift upper shell off. 3. Remove fan guard. IMPORTANT: Remove fan from motor shaft before removing motor from heater. -
Page 11: Air Output, Air Intake, And Lint Filters
Air Output, Air Intake, and Lint Filters 1. Remove upper shell (see page 10). 2. Remove filter end cover screws using 5/16" nut- driver. 3. Remove filter end cover. 4. Replace air output and lint filters. 5. Wash or replace air intake filter (see Preventative Maintenance Schedule, page 8). -
Page 12: Fuel Filter
Fuel Filter 1. Remove upper shell (see page 10). 2. Remove fan (see page 10). 3. Loosen flare nut using 3/4" open-end wrench. Push fuel tube down, away from burner head. Fuel filter is located inside of fuel tube. 4. Lift out fuel filter. 5. -
Page 13: Nozzle
Nozzle 1. Remove upper shell (see page 10). 2. Remove fan (see page 10). 3. Remove spark plug wire from spark plug. 4. Remove spark plug from burner head using 13/16" open-end wrench. 5. Loosen flare nut using 3/4" open-end wrench. Push fuel tube down. -
Page 14: Pump Rotor
Pump Rotor (Procedure if rotor is binding) 1. Remove upper shell (see page 10). 2. Remove filter end cover screws using 5/16" nut- driver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nut- driver. -
Page 15: Specifications
SPECIFICATIONS WIRING DIAGRAM ACCESSORY Purchase this accessory from your local dealer. Input Rating (BTU/Hr) Fuel Fuel Tank Capacity (U.S. Gallons/Imperial Gallons) Fuel Consumption (Gallons Per Hr/Imperial Gallons Per Hr) Electric Requirements Amperage (Normal Run) Hot Air Output (CFM/CMM) White Spark Plug Orange Ignitor Motor... -
Page 16: Illustrated Parts Breakdown And Parts List
ILLUSTRATED PARTS BREAKDOWN 28 43... -
Page 17: Wheels And Handles
This list contains replaceable parts used in your heater. When ordering parts, be sure PARTS LIST to provide the correct model and serial numbers (from the model plate), then the part number and description of the desired part. NO. PART NO. DESCRIPTION 098511-76 Upper Shell... -
Page 18: Burner Head Assembly
BURNER HEAD ASSEMBLY KEY PART NO. NO. DESCRIPTION M23103 Nozzle M10659-1 Nozzle Seal M10809-1 Nozzle Seal Spring M8882 Nozzle Seal Sleeve M51098-01 Burner Head Body M5976 Male Connector 079685-01 Male Connector 079722-01 Fuel Tube/Fuel Filter Assy. M10962-2 Spark Plug MOTOR AND PUMP ASSEMBLY KEY PART... - Page 19 NOTES...
-
Page 20: Warranty And Repair Service
DESA International, or any alteration or repair by others in such manner as in DESA International's judgement affects the Product materially and adversely, shall void this Warranty.