Related Manuals for Treif PRIMUS 400
Summarization of Contents
Before You Continue
Using These Operating Instructions
Explains how the operating instructions are structured and how to use them effectively for orientation.
Conventions
Details typographical conventions and warning systems used throughout the manual for clarity.
Manufacturer Address
Provides the official contact address and details for TREIF Maschinenbau GmbH.
Limitation of Liability
Outlines the manufacturer's limitations of liability regarding machine use and operation.
Copyright
States the copyright protection for the operating manual and its content.
Sale
Specifies that the operating manual is an integral part of the machine during sale.
Safety
Intended Use
Defines the specific purpose and authorized use of the machine.
Foreseeable Misuse
Identifies potential improper uses of the machine that are not permitted.
Owner of the Machine
Details the responsibilities and obligations of the machine owner.
Personnel
Covers personnel qualifications, responsibilities, and required protective equipment.
Information Signs on the Machine
Lists and describes the various safety and information signs found on the machine.
Placement of the Information Signs
Illustrates the specific locations of safety and information signs on the machine.
Placement of Rating Plate and Electrical Wiring Diagram
Indicates the locations of the machine's rating plate and electrical wiring diagram.
Safety Instructions
Provides general and machine-specific safety instructions for safe operation.
Safety Layout
Designates the location of key safety elements and features on the machine.
Product Information
The Machine at a Glance
Provides a general overview and identification of the machine's main components.
The Control Panel
Details the components and functions of the machine's control panel interface.
Technical Information
Presents detailed technical specifications and data for the machine models.
Dimensional Drawing
Includes diagrams showing the physical dimensions and measurements of the machine.
Transport and Installation
Safety Information About Transport
Highlights critical safety precautions to prevent accidents during machine transport.
Transport and Unpacking
Describes the procedures for safely unloading, unpacking, and inspecting the machine.
Installation and Connection
Provides instructions for the correct electrical connection and installation of the machine.
Set-up
Safety Instructions for Set-up
Outlines safety precautions to be observed during the machine setup process.
Dismantling the Blade
Details the step-by-step procedure for safely removing the machine's blade.
Installing the Blade
Provides instructions for the correct and safe installation of the machine's blade.
Start-up
Safety Instructions for Start-up
Details essential safety measures before starting the machine.
Start-ups
Explains different start-up procedures, including initial, restart, and post-emergency stop.
Functional Test of the Safety Switches
Guides on performing functional tests to ensure safety switch operation before use.
Switch-off
Describes the procedures for safely switching off the machine for various scenarios.
Operation
Safety Instructions for Operation
Provides crucial safety guidelines and warnings for operating the machine.
Initialisation
Explains the sequence for initializing the machine after power-on.
Product Length
Offers advice on handling products longer than the machine's insertion chamber.
Inserting and Cutting Product
Details the process of inserting products and performing slicing operations.
Slice Product Half with Previously Set Slice Thickness
Describes how to slice a product in half using a pre-set thickness.
Menu “Basic Slice Thickness”
Guides on how to preset and save the basic slice thickness for the machine.
If a Malfunction Occurs
Provides a troubleshooting guide with causes and remedies for common machine malfunctions.
Visualisation
General Information About the Display and Accessing Visualisation
Explains how to use the machine's display and navigate its menus for operation and setup.
Main Menu
Details the primary menu structure and available cutting modes for operating the machine.
Menu Bar
Describes how to access additional menu pages and functions via the menu bar.
Menu “Basic Slice Thickness”
Guides on preset basic slice thickness for consistent cutting and its configuration.
Menu “Statistics”
Shows machine data like slice counts, on-time, and blade wear for monitoring.
Additional Information on the Display
Provides details on various information and error messages shown on the machine's display.
Cleaning
Safety Instructions for Cleaning
Details essential safety precautions to be followed during cleaning procedures.
Cleaning Position for Blade
Explains how to move the blade to the correct position for safe cleaning.
Preparation for Complete Cleaning
Outlines the necessary steps to prepare the machine for thorough cleaning.
Instructions for Cleaning
Provides the requirements and methods for successful and safe machine cleaning.
Cleaning Schedule for Daily Cleaning
Presents a step-by-step schedule for performing daily cleaning of the machine.
Completion Work After the Cleaning
Details the final steps to be performed after cleaning is completed.
Maintenance
Safety Instructions for Maintenance
Highlights critical safety precautions for performing maintenance and repair work.
Personal Protective Equipment
Lists the necessary personal protective equipment for maintenance personnel.
Maintenance Overview
Provides a schedule of maintenance tasks and their recommended intervals.
Visual Inspection of Seal
Guides on performing a visual inspection of the seal in the knife drive area.
Sharpening the Blade
Explains the procedure for blade sharpening and where to send blunt blades.
Help and Service
Your Service Partner
Provides information on TREIF's service offerings and how to contact them.
If Any Fault Occurs
Offers a troubleshooting guide for common faults and their remedies.
Disposal
Decommissioning
Details the steps for safely shutting down and preparing the machine for disposal.
Disposal
Provides information on environmentally compliant disposal procedures for the machine.
Appendix
Proof of Training
A form to record and confirm that personnel have read and understood operating instructions.
Maintenance Record
A logbook for recording performed maintenance tasks and function checks.
Need help?
Do you have a question about the PRIMUS 400 and is the answer not in the manual?
Questions and answers