Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Atlas Copco PHE 30 Series
Summary of Contents for Atlas Copco PHE 30 Series
- Page 2 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Removing the 1 Removing the gear lever (6): gear housing Switch gear lever to „0“ and break it off with aid of pliers (the lever is being destroyed). 2 Only applicable for PHE 30 RX 2: Remove the hammer switch (5) with aid of pliers (the switch is being destroyed).
- Page 3 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Dismantling the 1 Removing the rear thrust bearing (7): spindle Lever off the special locking ring (8) with (removing the a screwdriver and remove it (peel it off inner locking like a key ring). The thrust bearing can be ring) removed in the following component parts:...
- Page 4 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Dismantling the 1 Press the following parts from the spindle: spindle – washer (6) (inner parts) – pressure sleeve (5) – plunger (4) PHE 24 R – brake disk (2) (is pressed in). PHE 26 R 2 Remove the O-rings (3) and (7).
- Page 5 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Dismantling the 1 Remove the service cover (6). handle 2 Remove the strain relief (5). 3 Loosen the cable (4). 4 Lever off the six handle cover (Softgrip) holders with aid of a screwdriver (see illustration) and remove the softgrip (3) 5 Remove the screws of the handle cover (2).
- Page 6 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Removing the 1 Remove the air deflector plate (1). field 2 Lightly hit the edge of the housing with a plastic hammer and expel the field (3) from the motor housing (5). 3 Remove the centering ledges (2). 4 Remove the rubber shell (4).
- Page 7 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Lubrication At each maintenance the tool must be lubricated as shown in the lubrication chart. After having dismantled the entire tool remove the used grease completely and replace it by new grease. Please pay attention to the following lubrication chart: Illustration: PHE 24RX Bauteil...
- Page 8 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Assembly Note Please additionally secure all screwed connections in metal with screw locking device. Mounting the 1 Insert the rubber shell (4). field 2 Insert the centering ledges (2) in the field (3). 3 Insert the field (3) in the motor housing (5) by hitting it lightly on the rear.
- Page 9 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Assembling the 1 Insert the AVS-rubber (1). handle 2 Fasten the handle cover (2) with screws. 3 Fasten the mains cable (4). 4 Fasten the strain relief (5). 5 Fasten the service cover (6) with screws. After the high-voltage check, fit the Softgrips (3).
- Page 10 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Mounting the 1 Insert the guide ring (4) and the bolt (3) back gear shaft into the cylinder (2). and the cylinder 2 Insert the rolls (6) into the back gear shaft one after the other and fix it with grease. Mount the rolls (6) completely with the cage (from date of manufacture 06/96).
- Page 11 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Assembling the 1 Mount the disk springs (1) with the spindle bulgings head-on (see illustration) (mounting the 2 Mount the clutch (the ratchet (2) with outer parts) indentations against the toothing of the spindle wheel (3)).
- Page 12 Repair Instruction No. 169.2/94 PAGE PHE 24/26/30-Range Mounting the 1 Insert the spring (8) and the retaining SDS-plus disk (7). Reception 2 Depress the retaining disk (7) and insert the ball (6). PHE 24 R 3 Fit the retaining ring (5) and the sliding PHE 26 R sleeve (4).
Need help?
Do you have a question about the PHE 30 Series and is the answer not in the manual?
Questions and answers