Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bemo N50
Summary of Contents for Bemo N50
- Page 1 Original operating instructions of the Seaming Machine for BEMO standing seam profiles types: N65 / N50 / VF65 Type II (esma) Read carefully and keep for future use! Date of issue Version Imprint: BEMO SYSTEMS GmbH Max-Eyth str. 2 18.02.2019...
-
Page 2: Table Of Contents
OPERATION ................................20 ..............................20 AFETY INSTRUCTIONS ............................20 EFORE THE SEAMING PROCESS 7.2.1 Preparation of BEMO-sheets ........................... 20 7.2.2 Security of the seaming machine ........................21 7.2.3 Use of the seaming machine on roofs ......................21 7.2.4 Use of the seaming machine on facades ......................21 7.2.5... - Page 3 ................................27 ERVICE ADDRESS STORAGE ................................28 DISPOSAL ................................29...
-
Page 4: Important Basic Information
The seaming machine for BEMO standing seam profiles Operating instructions Plastic roller set (4 rollers) for coated BEMO standing seam profiles Figure 1 If parts or components are not included in the scope of delivery or the machine is damaged, please contact us immediately (see service address below). -
Page 5: Legal Notices
BEMO SYSTEMS GmbH. BEMO SYSTEMS GmbH is not liable for damages resulting from the fact that the Operating instructions have not been observed or only partially observed. -
Page 6: Security
Chapter Security Security 2.1 Symbols used in the operating instructions The following symbols and signal words are used in this operating manual. These symbols should make the reader aware of the text of the safety note next to it. Symbol Signal word Definition Consequences... - Page 7 Chapter Security Symbols used in the operating instructions (continued) STOP! This symbol indicates a prohibition. This symbol requires to wear safety shoes. NOTICE! NOTICE! This symbol requires to wear a helmet. This symbol requires to wear hearing protection. NOTICE! WUFA_vers02.doc 7 of 29...
-
Page 8: General Safety Instructions For Power Tools
Chapter Security 2.2 General safety instructions for in any way. Do not use any adapter power tools plugs together with earthed equipment. Unmodified plugs and matching outlets will reduce the risk of electric shock. WARNING! Avoid body contact with earthed or Read all safety warnings and grounded surfaces such as pipes, radi- all instructions. -
Page 9: Careful Handling And Use Of Power Tools
Chapter Security Avoid accidental starting. Ensure the Disconnect the plug from the switch is in the off position before you power source before making connect it to the power supply, accom- adjustments, changing modate or carry it. accessories, performing Carrying power tools with your finger on maintenance and cleaning or the switch or plugging in power tools that moving the equipment away. -
Page 10: Service
This will ensure that the safety of the pow- er tool is maintained. only original parts of BEMO SYSTEMS GmbH for repair and mainte- nance. Use of accessories or spare parts that are not intended for this purpose may result in electric shock or injury. -
Page 11: Device-Specific Safety Instructions
The machine may only be operated, the machine. maintained and repaired by qualified Always use only the handles to personnel trained by BEMO System reach the machine when it is GmbH. This staff must be specifically switched on! informed of the hazards that occur. The... -
Page 12: Residual Risks
Chapter Security Make sure that the working area is always sufficiently illuminated. Never To identify the power tool, the housing work without lighting or at twilight. must not be drilled. The protective insulation will be broken. If the machine gets jammed, turn off it Use adhesive labels. -
Page 13: Description Of The Machine
230V / 50 Hz (110 V / 60 Hz) Motor with on/off switch and speed control Handles for mounting and dis- mounting of the seaming machine on the BEMO standing seam Lever The support rollers Setting angle The clamping screw of setting angle... -
Page 14: Intended Use
The seaming machine is determined for the close of the standing seam profile Chapter Intended use 3.2 types N65 / N50 / VF65 for sheet metal Machine is operated by untrained roofs and facades of the BEMO SYSTEM artisans or amateurs. -
Page 15: Duty To Take Care And Requirements For The Seaming Machine Operator
Failure to follow these operating / as- sembly instructions NOTICE! Ear Protection must be worn! NOTICE! Visit the training by BEMO SYSTEMS GmbH NOTICE! Read these operating instruc- tions and the installation instruc- tions for the BEMO standing... -
Page 16: Technical Data
The vibra- tion load could be underestimated if the BEMO standing machine is used regularly in such a way. Profiles allowed for the seam profiles N65 / work N50 / VF654 Note: For an accurate estimation of the vibration 4.1 Noise and vibration information... -
Page 17: Transport
Chapter Transport Transport Seaming machine must be transported to the place of use in the transport box. WARNING! The seaming machine must al- ways be transported in the transport box. Never transport the transport box to the place of use as a floating load. WUFA_vers02.doc 17 of 29... -
Page 18: Putting Into Operation
Steel rollers are mounted on the machine maximum speed. at delivery as standard. For the use of the machine with coated BEMO Systems GmbH standing seam profiles, the four steel rollers (1) must be disassembled and the plastic rollers (4) must be used as fol- lows: ... -
Page 19: Height Adjustment Of The Support Rollers
Chapter Putting into operation 6.3 Height adjustment of the support rollers Depending on the height of the standing seam profiles it may be necessary to ad- just the support rollers (5) in the height on both sides of the seaming machine. Figure 4: Height adjustment of the support rollers ... -
Page 20: Operation
Operation 7.2 Before the seaming process 7.1 Safety instructions 7.2.1 Preparation of BEMO-sheets The BEMO sheets must be prepared ac- Ear Protection must be worn! cordingly before seaming. For this pur- pose, the first 20-30 cm must be pre- seamed with the BEMO hand seaming tool The seaming machine may only before seaming with the seaming machine. -
Page 21: Security Of The Seaming Machine
Chapter Operation 7.2.2 Security of the seaming machine WARNING! The seaming machine must never be used on roofs and facades without supervision and security. Under no circum- stances should the machine fall from the roof / facade. 7.2.3 Use of the seaming machine on roofs ... -
Page 22: Placing Of The Seaming Machine On The Standing Seam
Open the lever (4) on the seaming ma- chine. Figure 9: Opening of the lever on the seaming machine Place the open machine on BEMO standing seam, so that support rolls (5) have contact with the sheet and the seaming rolls (10) are enclosing the big eye (11). -
Page 23: Connection Of The Seaming Machine
Chapter Operation WARNING! The machine runs automatically after switching on. Do not walk nearby the sheets and never place them on the machine. Make sure that the work area is free of tripping hazards. CAUTION! Always grab the seaming ma- chine on two handles. - Page 24 Chapter Operation is pulled, non-stable supply network, etc.), the machine stops. After the supply voltage has been restored, the machine must be switched off and switched on again. The machine is then ready for operation Figure 15 If necessary, the machine must be operated with both hands for the subsequent seaming operation, i.e.
- Page 25 Chapter Operation Figure 17: Opening of the lever on the seaming machine WUFA_vers02.doc 25 of 29...
-
Page 26: Maintenance And Cleaning
When coal is used, the machine switches off automatically. For Check the machine regularly for wear. this purpose please contact BEMO In the case of wear and tear please SYSTEMS GmbH. contact BEMO SYSTEMS GmbH. Only In order to maintain the protective... - Page 27 Chapter Maintenance and cleaning after use over a longer period of time (1 year), the machine must be sent to BEMO SYSTEMS GmbH for inspection and thorough cleaning. 8.4 Service address Telephone: +49 (0)7904 29899 60 Email: sales@bemo.com BEMO SYSTEMS GmbH Address: Max-Eyth str.
- Page 28 Chapter Storage Storage Regular cleaning and proper storage are important for the service life of the seaming machine. The clean, dry and oiled seaming machine must be stored in the transport box. WUFA_vers02.doc 28 of 29...
- Page 29 Chapter Disposal 10. Disposal Recycling of raw materials instead of waste disposal. Equipment, accessories and packaging should be treated in an environmentally compatible way for re-use. The plastic parts are marked for the recycling process. Do not dispose of power tools in household waste.
Need help?
Do you have a question about the N50 and is the answer not in the manual?
Questions and answers