Table of Contents
Advertisement
Owner's/Operator's Manual
TO THE OWNER/OPERATOR OF THIS IMPLEMENT
Please read this manual "before" unpacking or using this implement for the first time.
This manual provides you with the necessary instructions to safely install and use your
purchase. Do not let other people use this attachment without first being instructed
how to safely use it.
Save this manual for future reference!
X-treme Duty
XC7 & XCT
Brush Cutters
For safe operation, read these
rules and instructions carefully
to avoid accidents that could
result in Death or Serious Injury.
MTL Attachments
1906 Old Hwy 100
Tallapoosa, GA 30176
404-433-5364
Advertisement
Table of Contents
Related Manuals for MTL XCT
Summarization of Contents
Information
Record Product Information
Section to log serial number, date, dealer, and purchase details for future reference.
Safety
Importance of Safety
Emphasizes operator responsibility for safe operation and potential hazards.
Orientation
Introduces the physical layout and components of the brush cutter.
Operator Safety Training
Safety Warning Classifications
Explains DANGER, WARNING, CAUTION, and NOTICE symbols used in the manual.
Safe Operation Practices
Details essential safety tips for operating the brush cutter.
Using Your Implement
Skid Steer Requirements
Specifies minimum lift capacity, weight, and cab protection for the skid steer.
Unpacking Your Shipment
Instructions on how to safely remove the attachment from its shipping pallet.
Connecting Cutter to Skid Steer
Step-by-step guide for attaching the brush cutter to the skid steer coupler.
Pre-Operation Procedures
Pre-Operation Walk-around Inspection
Checklist for essential checks before each use to ensure safety and functionality.
Cutter Boom Controls
Explains how to operate the cutter's boom functions via skid steer controls.
Engaging Cutter the First Time
Initial startup steps, including checking hydraulic oil and purging air.
Operation Guidance
Starting the Cutter
Procedures for safely starting and engaging the brush cutter's drive hydraulics.
Stopping the Cutter
Instructions on how to safely disengage and stop the brush cutter.
Getting Familiar with the Attachment
Advice on understanding the attachment's behavior and operating safely.
Cutting Techniques
Adjusting Cutter Height & Level
How to set the cutter's deck elevation and tilt for optimal cutting.
Before Cutting
Pre-cutting checks of the work area and determining a safe cutting pattern.
Cutting Tips
Cutting Ground Level Vegetation
Specific techniques for cutting vegetation at ground level.
Cutting Above Ground Level Vegetation
Techniques for cutting taller vegetation using tilt and lift functions.
Maintaining Your Attachment
Lubrication Check & Add
Procedures for checking and adding grease to the bearing housing.
Maintenance Schedules
Before Every Use
Daily checks including fasteners, decals, and hydraulic oil levels.
Every Week
Weekly inspection of blades for condition and sharpness.
After Every Season
End-of-season checks for wear, cleaning, and proper storage.
Blade Holder Procedures
Blade Holder Removal & Installation
Step-by-step guide for safely removing and installing the blade holder.
Blade Procedures
Blade Removal & Replacement
Instructions for safely removing, inspecting, and replacing cutter blades.
Blade Installation
Process for installing new or sharpened blades, including torque specifications.
Blade Installation Images
Visual aids showing the correct installation of blades and hardware.
Hydraulic System
Hydraulic System Safety
Safety warnings and procedures related to hydraulic leaks and pressure release.
Hardware and Specifications
Hardware Torque
Table providing torque specifications for various bolt sizes and grades.
Parts Information
Parts Information Required
Details the information needed when ordering replacement parts.
Hydraulic Components
Lists specific hydraulic drive motors, lines, and couplers used in the attachment.
Component Parts
XC7 & XCT Cutter Parts - Bearing Housing
Exploded view and part list for the bearing housing assembly.
Troubleshooting
Cutter Bogs Down
Identifies causes like leveling issues or dull blades and provides resolutions.
Vibration Felt When Running Cutter
Addresses causes such as unbalanced blades or loose mounts and suggests fixes.
Blades Get Dull Too Quickly
Explains dulling due to contact with objects or wrong cutting height.
Blades Breaking
Discusses breaking due to shock loads from hitting solid objects.
Hydraulic Oil Level Goes Down
Points to leaks in the cutter motor, plumbing, or skid steer system.
Blades Do Not Spin When Flow is Activated
Covers issues like no oil flow, loose connectors, or drive shaft failure.
Limited Warranty
Warranty Exclusions
Lists parts and conditions not covered by the manufacturer's warranty.
Warranty Statement
Outlines the terms and conditions of the limited warranty, covering repairs and replacements.
Terms and Conditions
General Terms
Covers website usage, disclaimers, and acceptance of terms.
Warranty Disclaimer
Explicitly states MTL's warranty limitations and exclusions.
Blade Sharpening Recommendation
Advises using high-grade grinding discs for sharpening blades.
Need help?
Do you have a question about the XCT and is the answer not in the manual?
Questions and answers