Table of Contents
Advertisement
NX Blowers
Installation, Operation and Maintenance
Installation, Operation and Maintenance
EN
Instalación, operación y mantenimiento
ES
Installation, fonctionnement et entretien
FR
Installation, Betrieb und Wartung
DE
Installazione, funzionamento e manutenzione
IT
Save These Instructions
Authorized Hibon Distributor, Service & Repair Facility
120 – 10293 276 ST, Acheson, Alberta, Canada T7X 6A5
T: 780.962.1827 F: 780.962.1830 E: sales@fraserwoods.ca
www.fraserwoods.ca
80446693
Revision B
August 2013
Advertisement
Table of Contents
Related Manuals for Hibon NX 8
Summarization of Contents
1. INTRODUCTION
1.1 Scope and definitions
Defines the scope of the manual and key terms for the NX Blowers.
1.2 Description
Explains the components and basic design of the NX Blowers, including operating principle.
1.3 Applications
Outlines suitable and unsuitable applications for NX Blowers based on gas type and conditions.
2. TECHNICAL DATA
2.1 Operating and storage conditions
Lists environmental limits for operating and storing the NX Blowers, including temperature and humidity.
2.2 Mechanical data
Provides dimensional and mass specifications for different NX Blower models.
2.3 Performance
Details performance metrics like pressure, speed, and power for NX Blowers across various conditions.
2.4 Noise and vibration data
Specifies the noise levels and vibration characteristics of NX Blowers for user safety and system design.
2.5 Lubrication data
Details the types of oils, capacities, and specifications for proper lubrication of NX Blowers.
2.6 Materials of construction
Lists the materials used for various components of the NX Blowers, relevant for chemical compatibility.
2.7 Item Numbers
Explains how to identify and order different NX Blower configurations based on shaft orientation and mounting.
2.8 Connections
Provides detailed dimensions for inlet and outlet connections, and mounting points for NX Blowers.
3. INSTALLATION
3.1 Installation safety
Provides essential safety warnings and precautions that must be followed during the installation of NX Blowers.
3.2 System design and safety
Outlines critical system design requirements for safe and correct blower operation, including pressure limits.
3.3 Unpack and inspect
Instructions for safely unpacking and visually inspecting the NX Blower upon arrival for damage or missing parts.
3.4 Prepare, locate and connect the blower
Covers general considerations and procedures for positioning and connecting the blower into the system.
3.5 Fill the blower with oil
Instructions on how to correctly fill the blower with the specified lubricating oil for optimal performance and longevity.
3.6 Fit the drive/transmission
Guidance on installing the drive or transmission system, including pulley diameter and safety guards.
3.7 Check the direction of rotation
Procedure to verify the correct rotation direction of the blower after the drive system is connected.
3.8 Commissioning the blower
Steps to commission the blower, including initial run and performance checks before normal operation.
4. OPERATION
4.1 General operational safety
Crucial safety precautions to observe during the operation of the NX Blowers to prevent injury or damage.
4.2 Start-up
Step-by-step instructions for safely starting up the NX Blower, including checking oil levels.
4.3 Shut-down
Procedure for safely shutting down the NX Blower, ensuring all systems are stopped before closing valves.
5. MAINTENANCE
5.1 Safety information
General safety guidelines and precautions that must be followed before and during maintenance of the blower.
5.2 Maintenance plan
Outlines the recommended maintenance schedule, frequency, and corresponding sections for NX Blowers.
5.3 Check the oil levels
Instructions for checking the oil levels in the drive and non-drive head plates using sight-glasses.
5.4 Inspect the system installation
Guidance on inspecting system pipelines, connections, and the drive/transmission for maintenance integrity.
5.5 Change the oil
Detailed steps for draining and refilling the oil in both the drive and non-drive head plates.
5.6 Overhaul the blower
Recommendation for professional overhaul services, including bearing replacement, for the blower.
5.7 Fault finding
A guide to common symptoms, their possible causes, and troubleshooting actions for NX Blowers.
6. STORAGE AND DISPOSAL
6.1 Storage
Instructions for preparing and storing the blower, including precautions for short and long-term storage.
6.2 Disposal
Guidelines for safely disposing of the blower, used oil, and contaminated materials according to regulations.
7. SERVICE AND SPARES
7.1 Introduction
Information on the availability of Ingersoll Rand spares, accessories, and global service networks.
7.2 Service
Details the comprehensive services offered by Ingersoll Rand Service Centres, including repair and testing.
7.3 Spares and repair kits
Lists available spare parts and repair kits for the NX Blowers, including part numbers.
Need help?
Do you have a question about the NX 8 and is the answer not in the manual?
Questions and answers