Table of Contents
Advertisement
Quick Links
SFA Companies
E-mail: sales@bvahydraulics.com
!
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
SR05
MODEL NUMBERS: SR05 & SR10
10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419
*
Hydraulic Spreader
Instruction Manual
Fax: 816-891-6599
Website: www.bvahydraulics.com
SR10
SR05-M0 ver 07/08
Printed in China
Advertisement
Table of Contents
Related Manuals for BVA SR10
Summary of Contents for BVA SR10
- Page 1 SR05-M0 ver 07/08 Hydraulic Spreader Instruction Manual MODEL NUMBERS: SR05 & SR10 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 Fax: 816-891-6599 E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
-
Page 2: Product Description
Inspect before each use. Do not use if broken, bent, 4. Replace worn or damaged parts and assemblies with BVA cracked or otherwise damaged parts are noted. If any Hydraulics authorized replacement parts only. Lubricate component of this product has been or suspected to have as instructed in Maintenance Section. -
Page 3: Specifications
10,000 psi. refer repairs to qualified, authorized personal. • Do not connect a ram to a pump with higher Contact BVA Hydraulics tech service for authorized pressure rating. service center. • Do not subject ram to a shock loads, a load... -
Page 4: Basic Setup
Basic Setup The capacity of the maintenance kit can be significantly affected by the number of attachments used and the type of load applied. The approximate load capacity of each function setup is illustrated below. When two or more extension tubes are used together, be sure to position the shortest tube further away from the ram. -
Page 5: Operation
1. Inspect hoses and connections daily. Replace damaged 3. To bleed the air from pump reservoir, simply open the oil components immediately with BVA Hydraulics filler screw. Re-install after bleeding. Replacement Parts only. 2. Tighten connections as needed. Use pipe thread sealing compound when servicing connections. -
Page 6: Troubleshooting Guide
TROUBLESHOOTING GUIDE The following information is intended as an aid in determining if problem exists. Pump and ram should be repaired only by authorized BVA Service Center. For repair service, contact service center in your area. Symptom Possible Causes Corrective Action Erratic action •... -
Page 7: Limited Lifetime Warranty
• Damaged components, including but not limited to bent rams, dented or crushed ram walls, broken welds or couplers as well as worn out seals, o-rings and springs are the result of misuse and not covered by warranty and BVA Hydraulics will not provide any warranty credit for such damaged components. -
Page 8: Parts List
Release Valve Knob J0411 Serrated Saddle F040-90009-K03 Pump Handle J0412 Wedge Head (offset) F040-90107-K02 Oil Filler Screw J0413 Male connector F0400S-85 Seal Kit Note: To ensure safe and reliable performance, replace worn or damaged parts with BVA Hydraulics Authorized Replacement Parts only. - Page 9 H02-4-6001-104 Coupler, spreader H51-6-1002-207 Spreader base H51-6-1003-108 Spreader jaw axle H02-6-1008-105 Coupler cap H51-6-1004-100 Spring clip H02-4-6003-108 Dust cover 511-7-0240-406 O-ring SR05-M0 OIPM Note: To ensure safe and reliable performance, replace worn or damaged parts with BVA Hydraulics Authorized Replacement Parts only.
- Page 10 Load - Pressure Correlation For Model J50040 & J50100 Always monitor the force applied to workpiece by using a load cell and indicator or you may monitor pressure developed in the ram by using an inline pressure gauge, then calculate the applied force using the formula: where F = Force/ Load (lbs);...
- Page 11 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 E-mail: sales@bvahydraulics.com...
- Page 12 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 E-mail: sales@bvahydraulics.com...
Need help?
Do you have a question about the SR10 and is the answer not in the manual?
Questions and answers