Related Manuals for Edwards EMF20
Summary of Contents for Edwards EMF20
- Page 1 A462-26-880 Issue F Instruction Manual EMF3, EMF10 and EMF20 Oil Mist Filters Description Item Number EMF3 Oil Mist Filter A462-20-000 EMF10 Oil Mist Filter A462-26-000 EMF20 Oil Mist Filter A462-29-000...
- Page 2 This page has been intentionally left blank.
-
Page 3: Table Of Contents
Component parts of the EMF oil mist filters ................. 2 Dimensions (mm) ......................6 Fit the filter to the pump ....................8 © Edwards Limited 2008. All rights reserved. Page i Edwards and the Edwards logo are trademarks of Edwards Limited. - Page 4 A462-26-880 Issue F Tables Table Page Checklist of items ......................7 Page ii © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
-
Page 5: Introduction
Introduction Scope and definitions This manual provides installation, operation and maintenance instructions for the Edwards EMF Oil Mist Filters. You must use the EMF Oil Mist Filter as described in this manual. Read this manual before you install and operate your EMF series filter. Important safety information is highlighted as WARNING and CAUTION instructions;... -
Page 6: Component Parts Of The Emf Oil Mist Filters
Figure 1 - Component parts of the EMF oil mist filters Oil droplets Pump exhaust gas 1. Outlet 6. Inlet 11. Odour element 2. Odour element seal 7. Lower body (white) 12. Body half securing screws 3. Pressure relief valve assembly 8. -
Page 7: Applications
The EMF Oil Mist Filters are also suitable for use with chemicals that form azide compounds. If you have any doubt about the suitability of the filter for your application please contact your supplier or Edwards for advice. - Page 8 A462-26-880 Issue F This page has been intentionally left blank. Page 4 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
-
Page 9: Technical Data
For use with Edwards rotary pumps type EMF3 Speedivac 2, E2M1.5, E2M2 EMF10 RV3, RV5, RV8, E1M5, E2M5, E1M8, E2M8, E2M12 EMF20 RV12, E1M18, E2M18 © Edwards Limited 2008. All rights reserved. Page 5 Edwards and the Edwards logo are trademarks of Edwards Limited. -
Page 10: Dimensions (Mm)
A462-26-880 Issue F Figure 2 - Dimensions (mm) Oil Mist Filter Dimension EMF3 EMF10 EMF20 118.4 NW10 NW25 NW25 Page 6 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited. -
Page 11: Installation
Install the EMF filter on Speedivac 2 pumps Note: You can directly fit the EMF3 Oil Mist Filter to current models of the Speedivac 2 pump; however on early models (with Serial Numbers less than 26977), you will need to use two NW10 elbows (with the appropriate seals and clamps) to fit the filter. -
Page 12: Install The Emf Filter On Other Pumps
Figure 3 - Fit the filter to the pump 1. Filter 4. Adaptor 2. Centring-ring and O-ring 5. O-ring 3. Clamp 6. Pump Page 8 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited. -
Page 13: Operation
If you need to drain the filter very frequently, or if you want to reduce the amount of oil you use, fit an oil drain kit accessory: refer to Section © Edwards Limited 2008. All rights reserved. Page 9 Edwards and the Edwards logo are trademarks of Edwards Limited. - Page 14 A462-26-880 Issue F This page has been intentionally left blank. Page 10 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
-
Page 15: Maintenance
9. Refit the upper body (10) to the lower body (7) and secure with the screws (12) removed in Step 10. If fitted, reconnect your exhaust system pipeline to the filter outlet (1). © Edwards Limited 2008. All rights reserved. Page 11 Edwards and the Edwards logo are trademarks of Edwards Limited. - Page 16 A462-26-880 Issue F This page has been intentionally left blank. Page 12 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
-
Page 17: Storage And Disposal
Dispose of the EMF Oil Mist Filter, oil trapped in the filter and used filter elements safely in accordance with all local and national safety and environmental requirements. © Edwards Limited 2008. All rights reserved. Page 13 Edwards and the Edwards logo are trademarks of Edwards Limited. - Page 18 A462-26-880 Issue F This page has been intentionally left blank. Page 14 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
-
Page 19: Spares And Accessories
The majority of these centres employ Service Engineers who have undergone comprehensive Edwards training courses. Order spare parts and accessories from your nearest Edwards company or distributor. When you order, please state for each part required: Model and Item Number of your equipment... -
Page 20: Accessories
EMF Gravity Oil Drain Kit for RV3 to RV12, A505-01-000 E1/E2M2, 5, 8 and 12 pumps EMF Gas Ballast Oil Drain Kit for RV3 to RV12 pumps A505-23-000 Page 16 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
Need help?
Do you have a question about the EMF20 and is the answer not in the manual?
Questions and answers