Lexus GS450h 2016 Pre-Delivery Service Manual
  1. Manuals
  2. Brands
  3. Lexus Manuals
  4. Automobile
  5. GS450h 2016
  6. Pre-delivery service manual
Lexus GS450h 2016 Pre-Delivery Service Manual

Lexus GS450h 2016 Pre-Delivery Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

2016 GS200t/350/450h/F Pre-Delivery Service Manual
Lexus Technician:
Before you perform Pre-Delivery Service (PDS) on this vehicle, be sure you:
• Read and understand this PDS Manual
• Read and understand all applicable PDS Technical Service Information Bulletins (TSIBs) and Repair Manual
information for this vehicle
• Read and understand the PDS Precautions in the TSIBs and on pages 0, 5 and 56.
• Attend the "Technical Introduction to Lexus Course L005" at the Lexus Area Office
When performing PDS on this vehicle:
• Use the PDS Manual when performing this service
• Check the Technical Information System (TIS) for any updated PDS TSIBs and applicable Repair Manual information.
• Verify that the Vehicle Identification Number (VIN) on repair order and vehicle match
• Lift vehicle and perform under vehicle safety/damage inspection
• Road test vehicle long enough to test hot engine and drive over rough road (Bott dots) to test for rattles/squeaks
The following TSIBs and Repair Manual information are available on TIS (on TIS, click on Check Sheet links):
Battery Maintenance for In-Stock Vehicles & Pre-Delivery
D/C Cut Fuse Installation during PDS
Enform Apps & Data Services Download & Installation Process
Floor Mat Installation during PDS
Front License Plate & Mounting Bracket Installation
Front Wheel Opening Extension Pad Installation during PDS
Hybrid System Electrical Safety Precautions
Long-Term Vehicle Storage Guidelines
Maintenance for HV & Auxiliary Batteries
Parking Assist Monitor System Initialization
Tire Positioning Before New Vehicle Delivery
Tire Pressure Warning System Initialization
VGRS/LDH System Initialization
Wheel Film for Brake Rotor Rust Prevention
XM Activation Confirmation during PDS
TPWS Operation Verification
1. Connect Techstream to DLC3.
2. Adjust all tires, except the compact spare tire*, to the standard tire inflation pressure as indicated on the tire
and loading information label on vehicle.
NOTE:
• To adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop
temperature, perform a Health Check using Techstream and select the "Compensation Tire Pressure"
check box. Compensation pressures will be displayed on the Health Check results screen.
• Adjust the tire pressure when the tires are cold.
To obtain PDS material:
Manual
• Download from TIS website or Lexus Customer Services website on Dealer Daily
Check Sheet
• Download and print from TIS website or Lexus Customer Services website on Dealer Daily
• Sheet is two-sided; back side has procedure tips
Other PDS TSIBs and Repair Manual information
• Download from TIS website
Contact your District Service & Parts Manager if you have any questions.
ENGINE = POWER switch on hybrid models
© 2015 Lexus, a Division of Toyota Motor Sales USA, Inc.
* If equipped
JBS 20151117

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GS450h 2016 and is the answer not in the manual?

Questions and answers

Related Manuals for Lexus GS450h 2016

Summary of Contents for Lexus GS450h 2016

  • Page 1 2016 GS200t/350/450h/F Pre-Delivery Service Manual Lexus Technician: Before you perform Pre-Delivery Service (PDS) on this vehicle, be sure you: • Read and understand this PDS Manual • Read and understand all applicable PDS Technical Service Information Bulletins (TSIBs) and Repair Manual information for this vehicle • Read and understand the PDS Precautions in the TSIBs and on pages 0, 5 and 56. • Attend the “Technical Introduction to Lexus Course L005” at the Lexus Area Office When performing PDS on this vehicle: • Use the PDS Manual when performing this service • Check the Technical Information System (TIS) for any updated PDS TSIBs and applicable Repair Manual information. • Verify that the Vehicle Identification Number (VIN) on repair order and vehicle match • Lift vehicle and perform under vehicle safety/damage inspection • Road test vehicle long enough to test hot engine and drive over rough road (Bott dots) to test for rattles/squeaks The following TSIBs and Repair Manual information are available on TIS (on TIS, click on Check Sheet links): Battery Maintenance for In-Stock Vehicles & Pre-Delivery...
  • Page 2 2016MY GS200t/350/450h/F Pre-Delivery Service Manual...
  • Page 3 PRECAUTIONS The GS 450h has unique operating modes, so always follow the precautions below when performing the PDS operation: • The GS 450h contains high voltage (up to 650 volts) AC and DC Systems. All high voltage wiring and connections are orange in color. Do not carelessly touch these orange colored wiring harnesses and connectors. • The hybrid system may start up and shut down suddenly whenever the “READY” light is illuminated. Be sure to put the vehicle in “P”, apply the parking brake, and push the “POWER” switch OFF in order to stop the hybrid system (the “READY” light turns OFF), before working in the engine compartment. • The hybrid transaxle, engine radiator, and inverter radiator may reach high temperatures during inspection. Carefully observe all caution labels and instructions on these components. • Be sure to keep the vehicle in “P” at all times unless otherwise instructed. When the selector lever is in “N”, the hybrid vehicle battery will not charge even if the gasoline engine is operating. • When leaving the vehicle, put the selector lever in “P”, apply the parking brake, and push the “POWER” switch OFF in order to stop the hybrid system (the “READY” light turns OFF). • Air vents are located on the sides of the rear seats to cool the hybrid vehicle battery. Do not block these air vents. • Do not splash water on the electric components in the engine compartment. READ AND UNDERSTAND TSIB “Hybrid System Electrical Safety Precautions.” GS200t/350/450h/F...

  • Page 4: Table Of Contents

    TABLE OF CONTENTS INSPECTION DETAILS A. ENGINE COMPARTMENT ............1 B. LOCKS AND LIGHTS ..............6 C. LEFT FRONT ................13 D. LEFT REAR ................39 E. CARGO AREA ................43 F. RIGHT REAR ................45 G. RIGHT FRONT ................46 H. FRONT BUMPER ..............49 I. UNDER VEHICLE (SAFETY/DAMAGE) ........50 J. ROAD TEST ................54 COMPLETION ..................64 INDEX ....................67 GS200t/350/450h/F...
  • Page 5 TABLE OF CONTENTS Gasoline Vehicle - GS350 Page F use boxes ......................- Battery ........................3 Engine oil level dipstick ..................2 Engine coolant reservoir ..................5 Engine oil filler cap ....................- Brake fluid reservoir ....................4 Washer fluid tank ....................4 Electric cooling fans .................... 56 Condenser ......................- Radiator ......................... - NOTE: Install protective fender covers prior to beginning the under-hood inspection. GS200t/350/450h/F...
  • Page 6 TABLE OF CONTENTS Gasoline Vehicle - GS200t Page F use boxes ......................- Battery ........................3 Intercooler coolant reservoir ................. 5 Engine oil level dipstick ..................2 Engine oil filler cap ....................- Engine coolant reservoir ..................5 Brake fluid reservoir ....................4 Washer fluid tank ....................4 Condenser ......................- Electric cooling fans .................... 56 Radiator ......................... - NOTE: Install protective fender covers prior to beginning the under-hood inspection. GS200t/350/450h/F...
  • Page 7 TABLE OF CONTENTS Gasoline Vehicle - GS F Page F use boxes ......................- Battery ........................3 Engine oil level dipstick ..................2 Engine coolant reservoir ..................5 Engine oil filler cap ....................- Brake fluid reservoir ....................4 Washer fluid tank ....................4 Electric cooling fans .................... 56 Condenser ......................- Radiator ......................... - NOTE: Install protective fender covers prior to beginning the under-hood inspection. GS200t/350/450h/F...
  • Page 8 TABLE OF CONTENTS Hybrid Vehicle - GS450h Page Engine oil level dipstick ..................2 Engine coolant reservoir ..................5 Engine oil filler cap ....................- Power control unit coolant reservoir ..............5 Brake fluid reservoir ....................4 Fuse box ........................ - W asher fluid tank ....................4 Electric cooling fans .................... 56 Condenser ......................- Radiator ......................... - NOTE: Install protective fender covers prior to beginning the under-hood inspection.
  • Page 9 TABLE OF CONTENTS Page Engine switch ....................... 9 Shift lever......................55 Meters ........................ 22 Multi-information display ..................27 Parking brake switches..................57 Turn signal lever ....................11 Windshield wiper and washer switch ..............20 Emergency flasher switch................... 12 Trunk opener ..................... 21 Hood lock release lever ..................2 Tilt and telescopic steering control switch* ............27 Air conditioning system..................28 Audio system ...................... 29 Trunk opener main switch .................. 48 * If equipped GS200t/350/450h/F...
  • Page 10 TABLE OF CONTENTS GS 200t GS 350 GS 450h GS F Page Audio remote control switches................30 Paddle shift switches .....................- Talk switch ......................30 Meter control switches ..................30 Vehicle-to-vehicle distance button*..............60 Cruise control switch* ..................60 LKA (Lane-Keeping Assist) switch* ..............58 Telephone switches ....................30 * If equipped GS200t/350/450h/F...
  • Page 11 TABLE OF CONTENTS Page Inside rearview mirror ..................36 Sun visors ......................36 Vanity mirrors ......................36 Interior light ......................35 Personal lights ....................35 Moonroof switches....................37 “SOS” button* .....................38 Garage door opener switches ................38 * If equipped GS200t/350/450h/F VIII...
  • Page 12 TABLE OF CONTENTS Page Driving position memory switches ...............16 Outside rearview mirror switches ................18 Door lock switches ....................17 Power window switches..................17 Window lock switch ....................17 GS200t/350/450h/F...
  • Page 13 TABLE OF CONTENTS Page Seat heater switches* ..................35 Seat ventilator switches* ..................35 Remote Touch ....................31 Intuitive parking assist switch* ................34 Rear sunshade switch ..................37 Driving mode select switch ................. 61 Snow mode switch....................57 TVD switch**......................- * If equipped ** GS F only - not shown here (located near Snow mode switch) GS200t/350/450h/F...
  • Page 14 TABLE OF CONTENTS GS 200t GS 350 GS 450h GS F Page VSC OFF switch ....................62 Heated steering wheel switch* ................34 Automatic high beam switch* ................12 Instrument panel light control switches............... 19 Odometer/Trip meter and trip meter reset button ..........19 HUD (Head-Up Display) switches* ..............19 Brake hold switch* ....................58 ASC (Active Sound Control) switch*..............63 * If equipped GS200t/350/450h/F...
  • Page 15 INSPECTION DETAILS GS200t/350/450h/F...

  • Page 16: A. Engine Compartment

    PAINT FINISH (PAINT DEFECTS, DAMAGE) Visually and by hand inspect all body panels (doors, trunk, fenders, engine hood, roof panel) for surface damage from shipment or for any abnormalities (surface rust, paint flaking, chips, dents or scratches). NOTE: Carefully inspect all painted surfaces in a well-illuminated area (800-lux illumination is recommended). EXTERIOR PARTS FOR FIT Visually and by hand check the following parts for proper installation, rust, fit, misalignment and loose items: a) Front and rear bumpers b) Window moldings (front, side and rear) c) Lexus emblems (front and rear) d) Outside rearview mirrors e) Exterior lights such as headlights, turn signal lights, side marker lights and tail light lenses f) Doors, engine hood and fuel filler door g) Moonroof h) Front/Rear door panel protector i) Outside door handle j) Radiator grille k) Vehicle name emblems GS200t/350/450h/F...

  • Page 17: Engine Oil Level Dipstick

    INSPECTION DETAILS - A. ENGINE COMPARTMENT ENGINE HOOD RELEASE LEVER Use the engine hood release lever to check that the latch operates properly. Ensure that the engine hood opens and closes smoothly. ENGINE OIL LEVEL (ENGINE NOT RUNNING) a) Remove the engine oil level dipstick and wipe it clean. Reinsert the dipstick and pull it out to check the oil level. The level should be between the two marks. Low Normal Excessive b) Check the oil for dirt or impurities. NOTE: If the oil level is low, add specified engine oil and check for oil leaks. GS200t/350/450h/F...

  • Page 18: Battery

    INSPECTION DETAILS - A. ENGINE COMPARTMENT BATTERY TERMINAL TIGHTNESS AND Gasoline vehicles CHARGE a) Check the electrolyte level. If the electrolyte level is low, check the battery case for leakage. b) Check the battery charge. Measure the open-circuit battery voltage between the terminals. If the voltage reading is less than 12.6 volts, recharge the battery. NOTE: Before measuring the voltage, turn off the engine and all electrical systems. Wait 60 seconds to remove the surface Hybrid vehicles charge. If the engine was running before measuring the voltage, wait 20 minutes after the engine stops to remove the surface charge. c) Check that the battery terminals are properly connected and that the clamp is firmly installed. Terminals Hold-down clamp d) Print out battery charge test. WIRING AND HOSES a) Check the hoses, hose connectors and various clamps for tightness. b) Visually inspect the condition of all harness connectors and terminals for proper installation and tightness. GS200t/350/450h/F...

  • Page 19: Brake Fluid Reservoir

    INSPECTION DETAILS - A. ENGINE COMPARTMENT BRAKE FLUID LEVEL GS 200t/350/450h Visually check the fluid level through the reservoir. If the fluid level is low, replenish the brake fluid reservoir with FMVSS No. 116 DOT 3 or SAE J1703 brake fluid and check for fluid leaks. Brake fluid level should be at the “MAX” line (within 0.2 inches [5.0 mm] below). NOTE: Refer to the Repair Manual for fluid specifications. GS F WASHER FLUID LEVEL Open the washer tank cap and visually check the washer fluid level in the washer tank. The fluid level should be filled to within 2 inches of the cap. GS200t/350/450h/F...

  • Page 20: Intercooler Coolant Reservoir

    INSPECTION DETAILS - A. ENGINE COMPARTMENT ENGINE COOLANT LEVEL / HYBRID Engine coolant (GS350 shown; GS200t & GS450h similar) SYSTEM POWER CONTROL UNIT COOLANT LEVEL* Visually check the coolant level through the coolant reservoir tank when the engine/hybrid system is cool. The coolant level is satisfactory if the level is between the “FULL” and “LOW.” Reservoir cap FULL / “F” line LOW / “L” line Engine coolant (GS F) Only use “Toyota Super Long Life Coolant.” CAUTION: To avoid burning yourself, do not remove the radiator cap when the engine/hybrid system is hot. Power Control Unit coolant (GS450h only) Intercooler coolant reservoir (GS200t only) * If equipped GS200t/350/450h/F...

  • Page 21: B. Locks And Lights

    INSPECTION DETAILS - B. LOCKS AND LIGHTS WIRELESS REMOTE CONTROL Inspect the five functions of the system. Locks the doors Unlocks the doors Opens the windows and moonroof Opens the trunk Sounds the alarm a) Locking the doors 1. Close all the doors. 2. Press on the electronic key to lock all the doors from outside the vehicle. NOTE: When is pressed to lock doors, a beep will sound and all turn signal lights will flash once. However, if any door is not closed securely, pressing will cause the buzzer to sound continuously until all doors are properly closed. b) Unlocking the doors 1. Press on the electronic key once to unlock the driver’s door.

  • Page 22: Theft Deterrent System

    INSPECTION DETAILS - B. LOCKS AND LIGHTS SMART ACCESS SYSTEM a) With electronic key inside the vehicle, touch the lock sensor (on the upper part of the outside door handle) and the trunk lock button. Check that the buzzer sounds and that the doors do not lock. b) Take the electronic key out of the vehicle and touch the lock sensor again. Check that the door locks. NOTE: Recognition signals for the lock operation will operate up to two consecutive times. c) From a distance of at least 2.3 ft. (0.7 m), approach the vehicle and pull the driver and passenger side door handles, and the trunk opener. Check that the doors unlock. NOTE: The doors cannot be unlocked for 3 seconds after they were locked. THEFT DETERRENT SYSTEM With the doors locked, check that the system operates properly. System Test: a) Open the windows. b) Lock the doors by smart access system, wireless remote control or mechanical key. Be sure to wait until the security light on the center panel starts flashing. c) Unlock one of the doors using the inside door lock. The system should activate the alarm (horn sounds, headlights, tail lights and emergency flasher blink, interior light illuminates).
  • Page 23 INSPECTION DETAILS - B. LOCKS AND LIGHTS DOOR LOCK SYSTEM AND ILLUMINATED ENTRY SYSTEM a) Check that all doors open and close smoothly using the inside and outside door handles. b) Check that the doors cannot be opened by using the inside and outside door handles when the lock button is in the locked position (except front inside door handles). c) For front inside door handles: Check that the front doors can be opened by using the inside door handles when the lock button is in the lock position. d) Check exterior key lock control system operation by mechanical key (with driver’s door). Locks all doors Closes the windows and moonroof (turn and hold) Unlocks the door (two-step unlock function): 1. Turn the key once to unlock the driver’s door. 2. Turn the key again to unlock all the doors. Opens the windows and moonroof (turn and hold) e) Check that the outer footlight illuminates when the door is opened. OUTER FOOTLIGHT GS200t/350/450h/F...

  • Page 24: Engine Switch

    INSPECTION DETAILS - B. LOCKS AND LIGHTS POWER SUPPLY CHANGEOVER AND Hybrid vehicles; gasoline similar ENGINE START/STOP Check for proper activation of the “START STOP/ ENGINE”/”POWER” switch. Power supply changeover a) Carry the electronic key in the vehicle and apply the parking brake. b) Without depressing the brake pedal, press the engine switch and change the power supply. OFF Press once: “ACCESSORY” mode Press twice: “IGNITION ON” mode Press three times: OFF c) In each mode, check that the power supply has changed properly. Engine start/stop a) Carry the electronic key in the vehicle and apply the parking brake. b) Check that the shift lever is in the“P” position. c) While depressing the brake pedal, press the “START/ STOP ENGINE” switch. Hybrid system start/stop a) Carry the electronic key in the vehicle and apply the parking brake.

  • Page 25: Exterior Lights

    INSPECTION DETAILS - B. LOCKS AND LIGHTS EXTERIOR LIGHTS Walk around the vehicle and check that the following lights illuminate: a) Headlights b) Parking lights and daytime running lights c) Side marker lights (front) d) Front/Side turn signal lights e) Stop/Tail lights* e) Rear turn signal lights f) Side marker lights (rear) g) License plate lights h) High-mounted stoplight i) Back-up lights j) Outer footlights HEADLIGHT AIM If headlight aim is not correct, see Repair Manual for headlight aim procedure. ADAPTIVE FRONT LIGHTING (AFS)* Check that the indicator light illluminates when the AFS is deactivated. * If equipped GS200t/350/450h/F...

  • Page 26: Turn Signal Lever

    INSPECTION DETAILS - B. LOCKS AND LIGHTS TURN SIGNAL, HEADLIGHT, HIGH BEAM, AUTOMATIC HIGH BEAM* AND EMERGENCY FLASHER INDICATOR LIGHTS a) Check that the turn signal indicator lights on the instrument panel illuminate when the turn signal lever is moved up or down. Right turn Move the lever partway and release to signal a lane change (Right) Move the lever partway and release to signal a lane change (Left) Left turn b) Check that the headlight or tail light indicator illuminates when the headlight switch is on. The side marker, parking, tail, license plate and instrument panel lights turn on The headlights and all lights listed above turn on. The headlights, daytime running lights, and all lights listed above turn on and off automatically (when the ...

  • Page 27: Emergency Flasher Switch

    INSPECTION DETAILS - B. LOCKS AND LIGHTS e) Check operation of the automatic high beam* switch. f) Check that the turn signal lights and turn signal indicator lights blink when the emergency flasher switch is on. * If equipped GS200t/350/450h/F...

  • Page 28: C. Left Front

    INSPECTION DETAILS - C. LEFT FRONT INTERIOR PARTS FOR DAMAGE AND FIT Visually inspect the following interior parts for dirt, damage, and proper fit and alignment: a) Instrument panel, dashboard and glove box b) Roof headliner, pillar, roof side garnish and sun visors c) Door trim and quarter trim panels d) Seat upholstery, floor carpeting and door scuff plates e) Console box f) Steering wheel FLOOR MATS Check that the floor mats are designed specifically for this car. Fix them securely in place onto the carpet. PRE-COLLISION SYSTEM* Check the multi-information display to confirm that the PCS feature is ON. * If equipped GS200t/350/450h/F...
  • Page 29 INSPECTION DETAILS - C. LEFT FRONT SYSTEMS CHECK & ENFORM DOWNLOAD a) Check all systems with Techstream tester. For details on this procedure, refer to the engine troubleshooting section of the Repair Manual b) Tire Pressure Warning System initialization - refer to TSIB. c) TPWS Operation Verification 1. Connect Techstream to DLC3. 2. Adjust all tires (except the compact spare tire*) to the standard tire inflation pressure, as indicated on the tire and loading information label on vehicle. NOTE: To adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature, perform a Health Check using Techstream and select the “Compensation Tire Pressure” check box. Compensation pressures will be displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold. 3. Techstream Tire Pressure Information - print out. d) Health Check - print out. e) Enform Apps & Data Services Download & Installation Process - see TSIB. SEAT BELT Check seat belt operation.
  • Page 30 INSPECTION DETAILS - C. LEFT FRONT SEAT ADJUSTMENT Check seat adjustment operation. a) Seat adjustment Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch Vertical height adjustment switch Seatback upper angle adjustment switch* Lumbar support adjustment switch* Pelvic support adjustment switch* Seat cushion length adjustment switch* Seatback side support adjustment switch* b) Head restraint adjustment Pull the head restraints up Down Push the head restraint down while pressing the lock release button. c) Angle adjustment* d) Side support adjustment* * If equipped GS200t/350/450h/F...

  • Page 31: Driving Position Memory System

    INSPECTION DETAILS - C. LEFT FRONT DRIVING POSITION MEMORY SYSTEM a) Set driving position: With the engine switch in ON mode and the shift lever in the “P” position, check the operation: 1. Adjust the driver’s seat, steering wheel, outside rearview mirrors and HUD* to the desired positions. 2. While pressing the “SET” button, press button “1,” “2” or “3” until the buzzer sounds. 3. Check all buttons (1, 2 and 3) to make sure that all memorized settings operate correctly. b) Register set driving positions to a key: With the shift lever in the “P” position, close the driver’s door and turn the engine switch to ON mode. 1. Register a driving position to the button “1”, “2” or “3.” 2. Do not carry more than one key (including a card key*) when registering. While pressing the button “1,” “2” or “3,” press the driver’s door lock switch (either lock or unlock switch) until a signal beeps. 3. Unlock the driver’s door using the entry function or wireless remote control, open the driver’s door, and check that the stored driving position is recalled. c) Power easy access system Check that the steering wheel and driver seat automatically adjust to allow the driver to enter and exit the vehicle easily. * If equipped GS200t/350/450h/F...

  • Page 32: Door Lock Switches

    INSPECTION DETAILS - C. LEFT FRONT POWER WINDOWS AND DOOR LOCKS a) With the engine switch in ON mode, operate the power window switch for each window. Check that the power window up and down operation is smooth. Closing One-touch closing Opening One-touch opening b) Check that the windows (other than the driver’s window) cannot be operated when the window lock switch is on. c) Check operation of the power door lock switches from the driver’s and passengers’ doors. Locks all doors Unlocks all doors d) With the doors closed, check that the power windows can be fully operated after the engine switch has been switched to ACCESSORY or OFF mode. NOTE: This feature is canceled after 45 seconds or if either front door is opened. GS200t/350/450h/F...

  • Page 33: Outside Rearview Mirrors

    INSPECTION DETAILS - C. LEFT FRONT OUTSIDE REARVIEW MIRRORS a) Check power outside rearview mirror operation with the engine switch in the ACCESSORY or ON mode. 1. Press the master switch “L” (left) and “R” (right) and press the control switch in the desired direction (up, down or side-to-side). Check that the mirrors operate smoothly. 2. Press the switch to fold the mirrors. Press again to extend them to the original position. b) Press the “AUTO” switch to set automatic mode (folding/ extending of the mirrors links to locking/unlocking of the doors). Check that the indicator illuminates. c) Check the operation of the mirror defoggers. Press the rear window and outside rearview mirror defogger switch with the engine switch in ON mode. GS200t/350/450h/F...

  • Page 34: Instrument Panel Light Control

    INSPECTION DETAILS - C. LEFT FRONT ODOMETER AND TRIP METER DISPLAY Check operation of the odometer and trip meter display switch. INSTRUMENT PANEL LIGHT CONTROL Check that the instrument panel light control switch operates properly. Darker Brighter HEAD-UP DISPLAY* a) Press the head-up display main switch (“HUD”) and check that the head-up display appears on the windshield on the driver’s side. b) Use the switches to change brightness and location of the head-up display. Check that both operate properly. Head-up display Display brightness will change automatically according to the brightness of the surrounding area. “HUD” button Display brightness adjustment switch Display brightness can be adjusted to the desired level. Display position adjustment switch “DISP” button * If equipped GS200t/350/450h/F...

  • Page 35: Windshield Wipers And Washer

    INSPECTION DETAILS - C. LEFT FRONT WINDSHIELD WIPERS AND WASHER With the engine switch in ON mode: a) Pull the lever toward you and check that washer fluid squirts onto the proper area of the windshield and that wipers are activated. Wipers will make one additional pass after a short delay. b) Check wiper speed operation on all settings. Check that the wiper blades wipe off the washer fluid cleanly. c) The wipers should not make any abnormal noise when Intermittent type* operating. NOTE: • Intermittent type - The frequency of the intermittent wiper can be adjusted by turning the knob. • Rain-sensing type - The sensitivity of the sensor can be adjusted by turning the knob. • Add washer fluid up to the proper level. “OFF” - Move lever up two levels Move lever up one level Rain-sensing type* Move lever down one level “HI” - Move lever down two levels AUTO mode on/off switch* * If equipped GS200t/350/450h/F...

  • Page 36: Trunk Opener

    INSPECTION DETAILS - C. LEFT FRONT Rain-Sensing Function* d) With the wiper switch lever in the “AUTO” position, splash the water on the windshield around the windshield sensor and check that the wipers operate. HEADLIGHT CLEANERS* With the engine switch in ON mode and the headlights on, pull and hold the lever to check that washer fluid splashes on the headlights. TRUNK OPENER SWITCH Check operation of the trunk opener switch. * If equipped GS200t/350/450h/F...

  • Page 37: Indicator And Warning Lights

    INSPECTION DETAILS - C. LEFT FRONT INDICATOR AND WARNING LIGHTS a) With the engine switch in ON mode, check that each warning and/or indicator light operates properly. b) With the engine switch in ON mode, check that the following warning and/or indicator lights come on and then go off after a few seconds: • Brake system warning • Charging system warning* • Malfunction indicator • SRS airbag warning • ABS warning • Electric power steering system warning • Slip indicator • PCS (Pre-Collision System) warning* • AFS OFF indicator* • Brake hold operated indicator* • Brake system warning • Tire pressure warning • Master warning • VSC OFF indicator • TRAC OFF indicator* • Brake hold standby indicator* • Eco driving indicator • Air bag ON/OFF indicator See illustrations on next page. Refer to “Warning Lights and Buzzers” on page 24 for details. 2016 GS F * If equipped GS200t/350/450h/F...
  • Page 38 INSPECTION DETAILS - C. LEFT FRONT Except F SPORT models 2016 GS200t/350 F SPORT models Except F SPORT models 2016 GS450h F SPORT models GS200t/350/450h/F...
  • Page 39 INSPECTION DETAILS - C. LEFT FRONT Warning Lights and Buzzers Light/Buzzer Function/Condition Brake system warning light Brake System Warning • Low brake fluid Light and buzzer • Malfunction in the brake system Indicates a malfunction in the parking brake Brake System Warning system Light The driver’s and front passenger’s seat belt...
  • Page 40 INSPECTION DETAILS - C. LEFT FRONT Light/Buzzer Function/Condition A buzzer sounds and the warning light comes on or flashes to indicate that the master warning system has detected a Master Warning Light malfunction. If the master warning light comes on, a message appears on the multi-information display.
  • Page 41 INSPECTION DETAILS - C. LEFT FRONT Light/Buzzer Function/Condition Low Fuel Level Warning Indicates remaining fuel is approximately Light 2.6 gal. (9.7 L, 2.1 lmp.gal.) or less Indicates a malfunction in: • Vehicle stability control Slip Indicator • Traction control • Hill-start assist control Warning Message (on the Multi- Information Display) The multi-information display shows warning of system malfunctions, incorrectly performed operations, or shows messages that indicate a need for maintenance.

  • Page 42: Multi-Information Display

    INSPECTION DETAILS - C. LEFT FRONT MULTI-INFORMATION DISPLAY GS 200t/350/450h The multi-information display provides information on vehicle driving conditions and warning messages. Switch menu, change displayed content, scroll up/ down the screen and move the cursor Press: Enter/Set Press and hold: Reset Return to previous screen Display top screen GS F Press and hold: Register current screen as top screen NOTE: Refer to the multi-information display section in the vehicle’s Owner’s Manual for a comprehensive list of the system’s functions and displays. TILT AND TELESCOPIC STEERING WHEEL Check steering wheel adjustment operation: Down Toward the driver Away from the driver BLIND SPOT MONITOR* Check the multi-information display to confirm that BSM and RCTA are ON.
  • Page 43 INSPECTION DETAILS - C. LEFT FRONT AIR CONDITIONING AND HEATER Warm up the engine and check for smooth operation of each control: Select the “MENU” button on the Remote Touch. Select “ ” to display the air conditioning screen. a) Select high fan speed and set the temperature to 85 °F (29.5 °C) with the “TEMP” controls. b) Select windshield defogger from the control panel and check that hot air flows out of the front defogger vents. c) Select downward air flow and check that hot air flows out With rear air conditioning of the foot vents. d) Check that the airflow volume changes when the fan speed button is pressed on the control panel. e) Select “AUTO” followed by “DUAL” or “3-ZONE” (indicator on) and set the temperature of the driver’s side to 65 °F (18.5 °C). f) Check that the displays of the airflow mode and the air flow volume changes automatically by changing the temperature in auto mode. g) Check that the temperature of the passenger side remained at 85 °F (29.5 °C). h) Select upper body air flow mode (center vents). i) Check that cool air flows out of the driver’s side center vent and hot air flows out of the passenger’s side center vent. j) Press the “DUAL” or “3-ZONE” button (indicator off) and check that cool air flows out of both center vents. Set the temperature to 72 °F (22.2 °C).

  • Page 44: Audio System

    INSPECTION DETAILS - C. LEFT FRONT CLOCK Check/set clock so it displays correct time. a) Press the “MENU” button on the remote touch. b) Select “Setup” and then “General” to display the General Settings screen. c) Select “Clock” and adjust clock settings. AUDIO SYSTEM a) With the engine switch in the ACCESSORY or ON mode, press the “RADIO” button and check for proper operation of both AM and FM stations. b) Preset all the station memory buttons to local broadcast frequencies. c) CD/DVD player should be inspected for proper operation. d) USB and AUX port should be tested for proper operation. XM ACTIVATION CONFIRMATION Refer to TSIB. GS200t/350/450h/F...

  • Page 45: Steering Wheel Switches

    INSPECTION DETAILS - C. LEFT FRONT STEERING WHEEL AUDIO SWITCHES GS 200t/350/450h With the engine switch in ON mode, check each of the highlighted switches. Volume control switch Check that audio volume changes when the volume button on the steering wheel is pressed. RADIO mode Selects a radio station CD mode Selects tracks, files (MP3 and WMA) and discs GS F DVD mode Selects chapter and fast forwards/rewinds ® iPod player mode Selects a track USB memory player mode Selects a file and folder ® Bluetooth audio mode:...

  • Page 46: Remote Touch

    INSPECTION DETAILS - C. LEFT FRONT LEXUS NAVIGATION SYSTEM* a) With the engine switch in ACCESSORY or ON mode, check that the initial “LEXUS” screen appears for a few seconds and then changes to the “CAUTION” screen. NOTE: “CAUTION” screen appears if map or destination screen was displayed during last use. b) Press the “MENU” button on the remote touch to check each icon. Push the “ENTER” button for each and check that the display changes. NOTE: After about 5 seconds, the “CAUTION” screen automatically switches to the last display screen. HD TRAFFIC* To confirm activation, press the “MENU” button, select “Info” then select “Traffic Incidents.” Is traffic information displayed? NOTE: If service is currently unavailable, this may mean HD Data is not received by the vehicle after vehicle startup. Consult TIS for further diagnosis and repairs. * If equipped GS200t/350/450h/F...

  • Page 47: Cup Holders

    INSPECTION DETAILS - C. LEFT FRONT CUP HOLDERS Check that the cup holders open and close smoothly and that they do not make noise during operation. Check that the cup holder insert may be removed and reinserted without problem. CONSOLE BOX Check that the console box opens and closes smoothly and that it does not make any noise during operation. Check that the tray slides forward/backward and can be removed. GS200t/350/450h/F...
  • Page 48 INSPECTION DETAILS - C. LEFT FRONT POWER OUTLETS (12V) With the engine switch in ACCESSORY or ON mode, check the power outlets using an electrical accessory designed for this use. AUXILIARY BOX Check that the auxiliary box opens and closes smoothly and that it does not make any noise during operation. GS200t/350/450h/F...

  • Page 49: Intuitive Parking Assist Switch

    INSPECTION DETAILS - C. LEFT FRONT INTUITIVE PARKING ASSIST* This procedure is performed by placing safety cones at 6 points: a) With the engine switch in ON mode, press the intuitive parking assist switch. b) Check that the indicator light illuminates. c) The safety cones gradually approach the vehicle. 1. Front center sensor - about 3.3 ft. (100 cm) 2. Rear center sensor - about 4.9 ft. (150 cm) 3. Corner sensors - about 2.0 ft. (60 cm) d) Check that the buzzer sounds and the indicator bar is displayed on the screens. Front corner sensor operation Front center sensor operation Rear corner sensor operation Rear center sensor operation HEATED STEERING WHEEL* With the engine switch in ON mode, check that the indicator light comes on when the button is pressed. * If equipped GS200t/350/450h/F...

  • Page 50: Interior Light

    INSPECTION DETAILS - C. LEFT FRONT INTERIOR LIGHTS Check operation of the following interior lights: Outer foot lights Shift lever light Front interior light Front personal lights Inside door handle lights Rear personal lights Rear interior light Ornament lights Door courtesy lights Power window switch lights Footwell lights SEAT VENTILATORS* AND HEATERS* With the engine switch in ON mode, check that the indicator lights come on when each button is pressed. * If equipped GS200t/350/450h/F...

  • Page 51: Inside Rearview Mirror

    INSPECTION DETAILS - C. LEFT FRONT SUN VISOR AND VANITY MIRROR a) Check that the sun visor is easy to use: Flip down Unhook and swing to the side Side extender b) Slide the cover of the vanity mirror and check that the light comes on. ANTI-GLARE INSIDE REARVIEW MIRROR Check the anti-glare function switch operates properly. Indicator illuminates when in ON mode. GS200t/350/450h/F...
  • Page 52 INSPECTION DETAILS - C. LEFT FRONT MOONROOF With the engine switch in ON mode, check for smooth operation and any unusual noise. a) Open and close the moonroof Open: The moonroof stops slightly before the fully open position. Press switch again to fully open. Close: Lightly press either side of the moonroof switch to stop the moonroof partway c) Check the tilt function - up and down. Tilt up Tilt down d) The sun shade can be opened or closed manually; however, it will automatically open with the moonroof. REAR SUNSHADE CONTROL* With the engine switch in ON mode, check that the rear sunshade raises and lowers smoothly. * If equipped GS200t/350/450h/F...

  • Page 53: Sos" Button

    INSPECTION DETAILS - C. LEFT FRONT HomeLink GARAGE DOOR OPENER ® Check the HomeLink garage door opener by pressing each ® of the three buttons and observing that the indicator light illuminates. Final operational check requires programming. HomeLink indicator light ® Garage door operation indicators HomeLink icon - Illuminates while HomeLink ® ® operating Buttons SAFETY CONNECT ®* Inspect the Safety Connect LED (located in the overhead console) for a green activation status indicator. If green LED is not illuminated, press the SOS button once, wait for voice prompt, and press the button again within 5 seconds. If successful, tones will be heard followed by voice prompt saying “Activation is complete. Good-bye.” Green light will illuminate after call has ended. If the green light does not illuminate, please refer to TIS for troubleshooting procedures. “SOS” button LED light indicators Microphone NOTE: Vehicles may arrive with hanger requesting inspection to...

  • Page 54: D. Left Rear

    INSPECTION DETAILS - D. LEFT REAR CHILD PROTECTOR LOCK Check that the rear door cannot be opened by the inside door handle but can be opened by the outside door handle when the child protector is in the locked position. SIDE WINDOW SUNSHADE* Pull the tab and hook the shade on the anchors. Check that the side window sunshade can be raised and lowered smoothly. POWER WINDOW With the engine switch in ON mode, operate the power window switch. Check that the power window opens and closes smoothly. SEAT BELT Check seat belt operation. a) Check that the belt extends and retracts smoothly. b) Check that the belt is not twisted. c) Check that the buckle locks securely and releases smoothly. d) Check that the adjustable seat belt anchor operates properly and that it securely locks in position. * If equipped GS200t/350/450h/F...

  • Page 55: Rear Seat Head Restraints

    INSPECTION DETAILS - D. LEFT REAR REAR SEAT HEAD RESTRAINTS Check that the head restraints operate smoothly. AUXILIARY BOX* Check that the auxiliary box opens and closes smoothly and that it does not make noise during operation. POWER OUTLET (12V)* With the engine switch in the ACCESSORY or ON mode, check the power outlet using an electrical accessory designed for this use. POWER OUTLET (120V AC)* With the engine switch in the ACCESSORY or ON mode, check the power outlet using an electrical accessory designed for this use. * If equipped GS200t/350/450h/F...

  • Page 56: Trunk Storage Extension

    INSPECTION DETAILS - D. LEFT REAR ARMREST Check that the center armrest operates smoothly. TRUNK STORAGE EXTENSION Check that the armrest door can be locked and unlocked using the mechanical key. REAR CONSOLE BOX a) Auxiliary box Pull up the lever to release the lock. Check that the cover opens and closes smoothly. b) Rear cup holders Pull down armrest and push in and release to extend cup holders. Check that the cup holders open and close smoothly and that they do not make noise during operation. GS200t/350/450h/F...

  • Page 57: Rear Air Conditioning System

    INSPECTION DETAILS - D. LEFT REAR REAR AIR CONDITIONING SYSTEM* Check that the rear air conditioning controls on rear center console operate smoothly. REAR SEAT HEATERS* With the engine switch in ON mode, check that the indicator light changes each time a button is pressed. REAR AUDIO CONTROLS* Check that the rear audio controls operate properly. REAR SUNSHADE CONTROL* With the engine switch in ON mode, check that the rear sunshade raises and lowers smoothly. * If equipped GS200t/350/450h/F...

  • Page 58: E. Cargo Area

    INSPECTION DETAILS - E. CARGO AREA TRUNK a) Check that the trunk unlocks using the exterior button. b) When out of range, check that the trunk cannot be unlocked by pressing the trunk opener button when all the doors are locked by power door lock switch, wireless remote control, smart access system or key. c) Check that the trunk light comes on when the trunk is opened. TOOLS, JACK AND JACK HANDLE GS 200t/350/450h Check that the tools, jack and jack handle are properly installed. Jack handle Parking brake release tool Screwdriver Towing eyelet Wheel nut wrench Spare tire Jack GS F Jack handle Emergency tire puncture repair kit Parking brake release tool...

  • Page 59: Fuel Filler Door

    INSPECTION DETAILS - E. CARGO AREA TRIM APPEARANCE AND LUGGAGE CARPET FIT Inspect the luggage trim and luggage carpet for proper installation and appearance. TRUNK CLOSER SWITCH* 1. Check that the trunk closes automatically when the power trunk closer switch is pressed. 2. Press the switch while trunk lid is closing and check that the trunk lid opens again. FUEL FILLER DOOR Check that the fuel door opens and closes smoothly. * If equipped GS200t/350/450h/F...

  • Page 60: F. Right Rear

    INSPECTION DETAILS - F. RIGHT REAR SIDE WINDOW SUNSHADE* Check that the side window sunshade can be raised and lowered smoothly. POWER WINDOW With the engine switch in ON mode, operate the power window switch. Check that the power window up and down operation is smooth. AUXILIARY BOX* Check that the auxiliary box opens and closes smoothly and that it does not make noise during operation. SEAT BELT Check seat belt operation. a) Check that the belt extends and retracts smoothly. b) Check that the belt is not twisted. c) Check that the buckle locks securely and releases smoothly. d) Check that the adjustable seat belt anchor operates properly and that it securely locks in position. CHILD PROTECTOR LOCK Check that the rear door cannot be opened by the inside door handle but can still be opened by the outside door handle when the child protector is in the locked position. POWER WINDOW AND DOOR LOCKS a) With the engine switch in ON mode, operate the power window switch. Check that the power window up and down operation is smooth.

  • Page 61: G. Right Front

    INSPECTION DETAILS - G. RIGHT FRONT DRIVING POSITION MEMORY SYSTEM a) With the engine switch in ON mode and the shift lever in the “P” position, check the operation: 1. Adjust the passenger’s seat to the desired position. 2. While pressing the “SET” button, press button “1,” “2” or “3” until the buzzer sounds. 3. Check all buttons (1, 2 and 3) to make sure that all memorized settings operate correctly. b) Power easy access system* Check that the adjusted lumbar support, side support*, etc. will return to its original position when the front passenger door is opened. * If equipped GS200t/350/450h/F...
  • Page 62 INSPECTION DETAILS - G. RIGHT FRONT SEAT ADJUSTMENT GS 200t/350/450h Check seat adjustment operation. a) Seat adjustment Seat position adjustment switch GS F Seatback angle adjustment switch Seat cushion (front) angle adjustment switch Vertical height adjustment switch Seatback upper angle adjustment switch* Lumbar support adjustment switch* Pelvic support adjustment switch* Seat cushion length adjustment switch* Seatback side support adjustment switch* b) Head restraint adjustment Pull the head restraints up Down Push the head restraint down while pressing the lock release button c) Angle adjustment* d) Side support adjustment* * If equipped GS200t/350/450h/F...

  • Page 63: Glove Box

    INSPECTION DETAILS - G. RIGHT FRONT SEAT BELT Check seat belt operation. a) Check that the belt extends and retracts smoothly. b) Check that the belt is not twisted. c) Check that the buckle locks securely and releases smoothly. d) Check that the adjustable seat belt anchor operates properly and that it securely locks in position. SUN VISOR AND VANITY MIRROR a) Check that the sun visor is easy to use: 1. Flip down, unhook and swing to the side. 2. Check side extender operation. b) Slide the cover of the vanity mirror and check that the light comes on. GLOVE BOX Check that the glove box opens and closes smoothly and that it does not make any noise during operation. Open (push button) Unlock with mechanical key Lock with mechanical key LUGGAGE SECURITY SYSTEM Check that the luggage security system operates properly. GS200t/350/450h/F...

  • Page 64: H. Front Bumper

    INSPECTION DETAILS - H. FRONT BUMPER FRONT LICENSE PLATE & MOUNTING BRACKET INSTALLATION Refer to TSIB. GS200t/350/450h/F...

  • Page 65: I. Under Vehicle (Safety/Damage)

    INSPECTION DETAILS - I. UNDER VEHICLE (SAFETY/DAMAGE) BEFORE LIFTING VEHICLE WHEEL LUG NUT TORQUE (Should be checked if wheels have been taken off) Using a torque wrench, tighten all wheel lug nuts to the specified torque in the order of the numbers in the illustration to the left. Torque specifications: 76 ft-lbf (103 N•m, 10.5 kgf•m) INSTALL WHEEL CENTER CAPS Install the wheel center caps on the wheels. TIRES Visually inspect all tires for damage and/or defects. GS200t/350/450h/F...
  • Page 66 INSPECTION DETAILS - I. UNDER VEHICLE (SAFETY/DAMAGE) AFTER LIFTING VEHICLE REMOVE WHEEL FILM Visually inspect rotors for rust. NOTE: For the best rotor rust prevention, retain wheel film on vehicle until just prior to customer delivery. If leakage is found, see Repair Manual. CHASSIS INSPECTION FOR LEAKAGE OR DAMAGE a) Visually and by hand check the following components for proper installation, clamping, connection and damage: • Brake lines, hoses and protectors • Fuel lines, hoses and protectors • Steering linkage and dust boots • Drive shaft boots • Parking brake cable b) Visually check the entire underside of the body for proper rust-resistant coating. GS200t/350/450h/F...
  • Page 67 INSPECTION DETAILS - I. UNDER VEHICLE (SAFETY/DAMAGE) CHECK AND TIGHTEN ALL CHASSIS BOLTS OF COMPONENTS THAT ARE REPLACED DUE TO REPAIRS Check that all chassis bolts and nuts and suspension components are tight. See the Repair Manual for proper bolt torque specification. a) Front and rear suspensions b) Steering linkages c) Front/Rear cross members d) Front/Rear brakes e) Drive shaft(s)* f) Axle shafts FLUID LEAKS Visually check the following components for fluid leakage: a) Engine (cylinder head and around the head cover) b) Front brake system and lines c) Radiator and hoses d) Fuel lines and hoses e) Front differential*, transaxle* f) Front shocks g) Rear brake system and lines h) Rear shocks i) Rear differential*...

  • Page 68: Exhaust System

    INSPECTION DETAILS - I. UNDER VEHICLE (SAFETY/DAMAGE) EXHAUST SYSTEM Visually check for leaks and damage to the exhaust pipes and mufflers. Ensure they are properly installed. Softly hit cold pipes with fist. RUBBER BODY PLUGS Install the rubber body plugs into the torque box holes. NOTE: Plugs are shipped with the vehicle and put in the glove compartment. GS200t/350/450h/F...

  • Page 69: J. Road Test

    INSPECTION DETAILS - J. ROAD TEST BOTT DOT ROAD TEST LAYOUT As part of the PDS road test, the vehicle must be driven over a rough road surface or over Bott Dots in order to check for squeaks and rattles. If a rough surface is not available for this road test, Bott Dots should be installed on the dealership property where vehicles can be safely driven 5 to 10 mph. (See Bott Dots installation instructions below, as recommended and provided by TMC Quality Division.) Bott Dots are available at industrial supply outlets. GS200t/350/450h/F...

  • Page 70: Shift Lever

    INSPECTION DETAILS - J. ROAD TEST A comprehensive road test is vital in order to ensure that a perfect automobile is delivered to a Lexus customer. We recommend that you map out a specific road test course that includes a variety of road conditions including stop and go, highway speed and rough road surfaces.

  • Page 71: Electric Cooling Fans

    INSPECTION DETAILS - J. ROAD TEST PARKING ASSIST MONITOR* To initialize, see Repair Manual. With the engine switch in ON mode, and the shift lever in the “R” position, check that the rearview monitor system is displayed. ENGINE OPERATION WHILE DRIVING a) Check engine performance over a broad range of driving conditions including acceleration, cruising and deceleration. b) Make sure engine operation is smooth and responsive. c) Make sure that all the gauges operate properly. ENGINE OPERATION COLD AND HOT ELECTRIC COOLING FANS a) Check that the engine cooling fans rotate smoothly. CAUTION: The engine cooling fans are controlled depending on engine coolant temperature. Do not touch the fans when the engine is hot. b) Turn the air conditioning on and build up sufficient pressure. Check that the electric cooling fans turn on and rotate smoothly. CAUTION: The electric cooling fans are controlled depending on air conditioning refrigerant pressure. Do not touch the fans when the “A/C” switch is turned on.

  • Page 72: Parking Brake

    INSPECTION DETAILS - J. ROAD TEST PARKING BRAKE Check effort required to set the parking brake. Check for pull or any abnormal noise. a) Manual mode: Set the parking brake Press and hold switch and check that the parking brake indicator comes on. Release the parking brake Operate the parking brake while depressing the brake pedal and check that the parking brake indicator goes off. b) Automatic mode: With the vehicle stopped and the engine switch in ON mode, check that the brake warning light goes off when the shift lever is moved from the “P” position (and goes back on when it is moved into “P’). NOTE: When vehicle is in ON mode, the parking brake indicator light comes on until parking brake is released. When not in ON mode, or if the engine switch is turned off, the indicator stays on for approximately 15 seconds. SNOW MODE Check that the indicator light illumintates on the multi- information display when the switch is pressed. GS200t/350/450h/F...

  • Page 73: Brake Hold

    INSPECTION DETAILS - J. ROAD TEST BRAKE HOLD* a) Check that the green standby indicator light comes on when the brake hold system is activated. b) Check that the yellow brake hold indicator light comes on while the system is holding the brake. LKA (LANE-KEEPING ASSIST)* Check that the indicator light illuminates and a message is displayed on the multi-information display when the switch is pressed and released. The color of the LKA indicator signifies the following: White - LKA system is operating Green - Steering wheel assistance of the lane departure control function or lake-keeping assist function is operating Orange (flashing) - Lane departure alert function is operating EV DRIVE MODE* Check that EV drive mode operates properly and that the indicator illuminates on the multi-information display when the button is pressed. * If equipped GS200t/350/450h/F...
  • Page 74 INSPECTION DETAILS - J. ROAD TEST CHECK BLIND SPOT MONITOR WITH REAR CROSS TRAFFIC ALERT FUNCTION* STEERING OPERATION AND OFF-CENTER a) Check steering for smooth turning operation and any unusual noise. b) Check that the steering wheel is correctly aligned when driving on a level road surface. NOTE: For details about adjustment and inspection, refer to the Repair Manual. AIR CONDITIONING AND HEATER FUNCTIONS SQUEAKS AND RATTLES Check for squeaks and rattles in the following: a) Instrument panel b) Doors c) Trim d) Body e) Other TRANSAXLE OPERATION...

  • Page 75: Vehicle-To-Vehicle Distance Button

    INSPECTION DETAILS - J. ROAD TEST CRUISE CONTROL* a) Check the cruise control functions: • ON-OFF • SET • CANCEL • RESUME b) Check that the preset speed is canceled by: • Depressing the brake pedal • Using cancel switch and “ON-OFF” button For details regarding the operation of the cruise control, refer to the Owner’s Manual. Dynamic Radar Cruise Control System* c) Press the “ON-OFF” button and check that the indicator in the instrument cluster comes on and “RADAR READY” appears on the multi-information display. (Vehicle-to-vehicle distance control mode) d) Press the “ON-OFF” button for 1.5 seconds or more to check that dynamic radar cruise control changes to conventional (fixed speed) cruise control. (Indicator in the instrument cluster will change.) Vehicle-to-vehicle distance button Display Set speed Indicators Cruise control switch e) Check that the vehicle-to-vehicle distance setting is changed from “Long” to “Medium” to “Short” and then...

  • Page 76: Driving Mode Select

    INSPECTION DETAILS - J. ROAD TEST DRIVING MODE SELECT Check that the driving modes operate properly. Vehicles without AVS (GS 200t/350) Normal mode Press switch to change the driving mode to normal mode if eco or sport mode is already selected. Eco driving mode When not in eco drive mode, turn switch to the left and check that the “ECO” light illuminates. Sport mode When not in sport mode, turn switch to the right and check that the indicator light illuminates. Vehicles with AVS (GS 200t/350/450h) Normal mode/Customized mode Press switch to toggle between Normal and Customized mode. Check that the “CUSTOMIZE” indicator illuminates on the display when customized mode is selected. Eco drive mode When not in eco drive mode, turn switch to the left...

  • Page 77: Vsc Off Switch

    INSPECTION DETAILS - J. ROAD TEST TRAC AND/OR VSC SYSTEM GS 200t/350/450h a) Disabling the TRAC system Check that the indicator light illuminates or a message is shown on the multi-information display when the switch is quickly pressed and released. Push again to turn the system back on. b) Turning off the TRAC and VSC systems Check that the VSC OFF indicator light illuminates and a message is shown on the multi-information display when the switch is pressed and held for more than 3 seconds. GS F GS F - Expert mode c) Expert mode (GS F only) Press the VSC off switch when in SPORT S+ mode to select expert mode; check that the “EXPERT” indicator light illuminates along with the TRAC OFF and VSC OFF indicators. To cancel expert mode, press the VSC OFF switch again or change driving mode to a mode other than SPORT S+. GS200t/350/450h/F...
  • Page 78 INSPECTION DETAILS - J. ROAD TEST ABNORMAL NOISE OR VIBRATION Check for vibration or abnormal noise while the vehicle is in motion. a) Wind noise b) Power train (engine, transaxle, rear differential*) c) Road noise (tires) d) Other ASC (ACTIVE SOUND CONTROL) The ASC system can be operated when in sport mode. SPORT S mode: Sounds are output from the rear SPORT S+ mode: Sounds are output from the front and rear Disable: Press the ASC switch and check that the indicator on switch turns off. BRAKE LIGHTS AND BACKUP LIGHTS CHECK HORN TURN OFF RADIO, AIR CONDITIONING, SEAT HEATERS, LIGHTS OWNER’S MANUALS AND PORTFOLIO a) Place the Quick Guide booklet(s) in the glove box.

  • Page 79: Completion

    COMPLETION COMPLETION GS200t/350/450h/F...
  • Page 80 I have attended the "Technical Introduction to Lexus Course L005" at the Lexus Area Office. I have read and understand the PDS Manual, PDS precautions, and applicable PDS TSIBs. I have lifted the vehicle and performed under vehicle safety/damage inspection. I have road tested vehicle long enough to test hot engine and driven over rough road/Bott dots to test for rattles/squeaks.
  • Page 81 COMPLETION BATTERY MAINTENANCE FOR IN-STOCK VEHICLES & PRE-DELIVERY Refer to TSIB. MAINTENANCE FOR HV/AUXILIARY BATTERY BEFORE DELIVERY Refer to TSIB. LONG TERM VEHICLE STORAGE GUIDELINES Refer to TSIB. FLOOR MAT INSTALLATION DURING PDS Refer to TSIB. GS200t/350/450h/F...

  • Page 82: Index

    INDEX Exterior lights Power supply changeover Technical Service Information Bulletins Available on TIS Floor mats Power window 17,39,45 SEE LIST ON FRONT COVER Fuel door Pre-collision system Glove box Rubber body plugs Manual Glove box portfolio Safety Connect Active sound control HD traffic Seat adjustment 15,47 Adaptive front lighting Headlight aim Seat belt 14,39,45,48 Air conditioning 28,42 Headlight cleaners Seat heaters/ventilators Anti-glare inside rearview mirror 36 Headlights Seat heaters, rear Armrest Head restraints 15,40,47 Shift lock override Audio system 29,42...

Table of Contents