BedJet 6002NA V2 User Manual
  1. Manuals
  2. Brands
  3. BedJet Manuals
  4. Temperature Controller
  5. 6002NA V2
  6. User manual

BedJet 6002NA V2 User Manual

Bed climate comfort system with remote control & bluetooth app
Hide thumbs

Advertisement

Table of Contents

USER MANUAL – MODELS 6002NA/V1/V2/ & 7002xx
QUESTIONS? EMAIL US AT INFO@BEDJET.COM OR CALL 401-404-5250
WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE!
®
Bed Climate Comfort System
with Remote Control & Bluetooth App
This device is for residential home use only. It is not intended to be
used in commercial, industrial, or human medical settings.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE,
INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL
SAFETYINFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
SAVE THESE INSTRUCTIONS
Revision 1.6 www.bedjet.com
P a g e | 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 6002NA V2 and is the answer not in the manual?

Questions and answers

Related Manuals for BedJet 6002NA V2

Summary of Contents for BedJet 6002NA V2

  • Page 1 USER MANUAL – MODELS 6002NA/V1/V2/ & 7002xx QUESTIONS? EMAIL US AT INFO@BEDJET.COM OR CALL 401-404-5250 WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! ® Bed Climate Comfort System with Remote Control & Bluetooth App This device is for residential home use only. It is not intended to be used in commercial, industrial, or human medical settings.

  • Page 2: Letter From The President

    WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! Letter from the President: Thank you for your purchase of the BedJet. We wanted you to know who we are. Our company is not a division of a massive multinational consumer appliance company or funded by big corporate capital.

  • Page 3: Important Instructions

    5. Do not operate device unattended. Turn off or unplug when not in use. 6. DO NOT OPERATE MORE THAN ONE BEDJET ON SAME BEDROOM AC-POWER CIRCUIT WITHOUT ADJUSTING DUAL MODE SWITCH LOCATED ON REAR OF DEVICE TO “DUAL ZONE ON, LOW POWER”...
  • Page 4 14. This device has hot and arcing or sparking parts inside. Do not use the BedJet in areas where gasoline, paint, or flammable liquids are used or stored. It must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres.
  • Page 5 USER MANUAL – MODELS 6002NA/V1/V2/ & 7002xx QUESTIONS? EMAIL US AT INFO@BEDJET.COM OR CALL 401-404-5250 WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! c) During use check frequently to determine if your plug outlet or faceplate is HOT! d) If so, discontinue use of the heater and have a qualified electrician check and/or replace the faulty outlets.

  • Page 6: Manufacturer Information

    USER MANUAL – MODELS 6002NA/V1/V2/ & 7002xx QUESTIONS? EMAIL US AT INFO@BEDJET.COM OR CALL 401-404-5250 WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! THIS DEVICE IS A DOUBLE INSULATED PRODUCT: SERVICING OF DOUBLE-INSULATED PRODUCTS In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated product, nor is a means for grounding to be added to the product.

  • Page 7: Product Overview

    The BedJet ® base unit is intended to be installed underneath the bed, or at the foot of the bed. The BedJet product cools and heats your bed while keeping all electricity safely out of your bed where it belongs.

  • Page 8: Pre-Installation Checklist

    QUESTIONS? EMAIL US AT INFO@BEDJET.COM OR CALL 401-404-5250 WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! Pre-Installation Checklist Before attempting installation of the BedJet, please verify the following standard parts list from your BedJet package: Adjustable height mattress mount Air Nozzle with qty.
  • Page 9 WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! Proper Assembly Required: The BedJet is required to be installed onto a bed for proper operation. All parts included are required to be fully assembled and installed onto the BedJet as part any operation. Do not operate the BedJet without the included Air hose and Air Nozzle installed onto the BedJet.

  • Page 10: System Overview

    BedJet Status Display: Located on top of the BedJet, the Status Display gives information on current mode setting of the BedJet. This is not a control panel. Controlling the BedJet is performed via the wireless remote or Bluetooth smartphone/tablet App.
  • Page 11 BEDJET REMOTE CONTROL SYNC TO BEDJET: The wireless remote control needs to be paired to your BedJet in order to correctly operate. This is normally done at the factory prior to delivery. If BedJet is powered on (verified by Power LED on BedJet display) and wireless...
  • Page 12 Installations where only one BedJet is used on the same household branch AC Circuit and one BedJet device is installed on the bed should set the Dual Zone Switch OFF to HIGH power 1500W to enjoy the full power heating comfort of the system. Users with single or twin size beds should set the Dual Zone Switch to LOW Power.

  • Page 13: Maintenance

    Use the following instructions for a single zone BedJet installation. A single zone BedJet installation is a single BedJet installed on any size bed, resulting in heating or cooling of the entire bed as a single temperature zone. Settings on medium or low may allow only half sections of the bed to be heated or cooled if desired (see Step #3).
  • Page 14 USER MANUAL – MODELS 6002NA/V1/V2/ & 7002xx QUESTIONS? EMAIL US AT INFO@BEDJET.COM OR CALL 401-404-5250 WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! 3) Determine best Air Nozzle location near the bottom of the bed per your personal heating and cooling zone preferences on the chart below and limitations of your bedframe.
  • Page 15 Add Height Links if Air Nozzle flops off mattress too easily. 9) Place BedJet on the floor near the bottom of the bed directly beneath the Mattress Mount, the intake should be facing towards the bed.
  • Page 16 13) Familiarize yourself with turning on and off the various operating modes while the Status Display of BedJet is visible before the BedJet is pushed under the Bed. 14) The ideal BedJet final installation location is under the bed. This product is designed to be an extension of your bed and has been electrically approved as safe for this installation.
  • Page 17 The BedJet is articulated bed frame approved. It will work fine underneath adjustable bed frames, provided care is taken to make sure that the BedJet and Air Hose are installed in a location where the full range of frame articulation will not crush either component. This may require fully extending the Air Hose to move BedJet further away from the Air Nozzle/Mattress mount location than shown here.
  • Page 18 Utilize the Bluetooth linked BedJet App from your smartphone or tablet computer to unlock advanced features.  The BedJet main power switch (under the power cord) must be turned ON for the remote control to function. Once the power switch is ON, the BedJet will beep once to indicate successful boot-up of the internal microcontroller.
  • Page 19 Ambient bedroom air temperature must generally be below 79 °F (26 °C) for cooling mode to be effective. For night sweats, also try using the BedJet App to set the BedJet heat mode to its lowest temperature settings. For most this will provide some cooling while also helping dry the bed.
  • Page 20 This condition results from use a top sheet that is not compatible with the BedJet, or use of no top sheet at all and just a loose knit blanket. At 100% airflow your bed should have nearly all of your bedding ballooning slightly off the bed and air flow will be felt exiting at the very top of the bed from under the top sheet.
  • Page 21 Auto-Shutoff by 1 additional minute, to maximum of 10 minutes.  Do not continuously re-cycle the BedJet into Turbo-Heat mode while in bed.  Do not place body parts directly into or in front of Air Nozzle in TurboHeat mode ...
  • Page 22 12 hours. You can even program the BedJet to wake you up in the morning with a cool blast of air! Real time information is displayed on the App on Air Flow power setting, Air Flow temperature, and time remaining to Auto-shutoff.
  • Page 23 Download the BedJet App from the Google Play Store. Once the BedJet is powered on, run the BedJet App and press the blue window on the bottom left of main screen that says “Pair”. On following screen press Search, the local BedJet device should show up on the list. Press the device ID and the pairing should begin.
  • Page 24  Ambient bedroom temperature sensing and programmable actions based on room temp.  BedJet v2 operating firmware can be updated via smartphone link to keep your BedJet up to date with the latest improvements.
  • Page 25 When operating with a BedJet, the AirComforter looks wonderfully puffy, luxurious and down filled, but it’s actually only filled with conditioned air from the BedJet, making it one of the softest and lightest comforters ever created! The AirComforter sheet can be used in the following configurations: Single BedJet: One BedJet is installed on the bed and the BedJet’s heating and cooling power is...

  • Page 26: Specifications

    WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! Specifications The BedJet has been designed to operate as a safe extension of your bed. This product has been rigorously tested by an accredited 3 party testing lab to be qualified as a safe electric appliance. The BedJet complies with the following safety and product standards: ...

  • Page 27: Troubleshooting

    WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! Troubleshooting Use this guide to address problems with your BedJet Product. If problems cannot be resolved, please contact Customer Service at info@bedjet.com or +1.401.404.5250. Do not return any product requiring service without first obtaining Return Authorization Number (RMA) and shipping instructions.
  • Page 28 USER MANUAL – MODELS 6002NA/V1/V2/ & 7002xx QUESTIONS? EMAIL US AT INFO@BEDJET.COM OR CALL 401-404-5250 WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! Diagnose & Fix Issue Possible Causes Action Every LED light on BedJet  ...
  • Page 29 USER MANUAL – MODELS 6002NA/V1/V2/ & 7002xx QUESTIONS? EMAIL US AT INFO@BEDJET.COM OR CALL 401-404-5250 WE ARE HERE TO HELP – PLEASE CALL US FOR ADVICE! Diagnose & Fix Continued Issue Possible Causes Action BedJet is on but  Check to make sure Air Nozzle and ...
  • Page 30 God (such as a flood) is not covered. BEDJET LLC does not have any obligations if our inspection reveals that the product has been altered, modified, damaged, subjected to or involved in an accident, disassembled, repaired or attempted to be repaired by someone other than us, or used in a manner in consistent with its intended purpose.

Table of Contents

Save PDF