Related Manuals for System One S1-M
Summarization of Contents
General Information and Precautions
Caution on Cable Usage
Warning about using specified cable which can cause performance issues and void warranty.
Important Installation Notes
Responsibility disclaimer for improper cable use or external interference. Correct interference at source.
Equipment Location Guidelines
Master Station Placement
Guidelines for locating the Master Station, including height, wall depth, and tiling considerations.
Room Station Placement
Recommendations for Room Station placement, avoiding feedback, height, fixing, and environmental considerations.
Component Installation Locations
Front Door/Gate Station Location
Location recommendations for front door/gate stations, including height and weather protection.
Power Supply Location
Guidance on locating the power supply for easy access and effective heat dissipation.
Antenna Placement
Advice on positioning AM and FM antennas for optimal radio reception, especially with foil insulation.
Auxiliary Input Jack Setup
Description of auxiliary input jacks for external audio sources and their types.
Auxiliary Boards and Cable Routing
Auxiliary/Lock Output Board Details
Details on optional boards for controlling door locks, gates, lights, and their installation.
Cable Routing Guide
Guidance on routing intercom cables, avoiding electrical wiring, and antenna wire placement.
Cable Selection and Power Supply
General Cable Information
Information on system wiring (8-wire vs 6-wire), cable types, and cable tagging recommendations.
Power Supply Cable Extension
Guidelines for extending power supply cable length and calculations for power supply cable resistance.
Cable Resistance Example
Illustrative example calculating maximum cable lengths based on power supply cable resistance.
Antenna and Input/Output Board Connections
AM Aerial Connection
Instructions for connecting the AM aerial cable from the Master to the loop antenna.
FM Aerial Connection
Instructions for connecting the FM aerial cable from the Master to the highest point in the roof.
Optional Auxiliary Input Jacks
Details on the two types of Input Jacks available and their connection methods.
Optional Auxiliary/Lock Output Boards
Requirements for auxiliary/lock output boards, including hook-up wire and cable resistance.
Room Station Only Systems Diagrams
Star Wired System Diagram
Diagram showing the star wiring configuration for Room Station only systems.
Loop Wired System Diagram
Diagram illustrating the loop wiring configuration for Room Station only systems.
Master Station Installation
Timber Frame Wall Installation (Not Lined)
Instructions for installing the Master wall box in a timber frame wall before lining.
Timber Frame Wall Installation (Already Lined)
Steps for installing the Master wall box in an already lined timber frame wall.
Master Station Installation in Brick Walls
Brick Cavity Wall Installation
Procedure for installing the wall box for the Master Station in a brick cavity wall.
Fitting Master Back Housing and Brackets
Detailed steps for fitting the Master Station's back housing and mounting brackets.
Master Station Wiring and Brackets
Tamper Switch and Lid Brackets
Diagrams showing exploded and assembled views of mounting brackets for tamper switch and lid.
Connecting Intercom Wiring
Step-by-step guide for stripping and connecting intercom cables to the Master termination PCB.
VM102 Master Cable Termination Variations
Valet Cable with Auxiliary Output
Diagrams for VM102 Master terminations using Valet Cable with an Auxiliary Output Board.
Cat 5 Cable without Auxiliary Output
Diagrams for VM102 Master terminations using Cat 5 Cable without an Auxiliary Output Board.
Cat 5 Cable with Auxiliary Output
Diagrams for VM102 Master terminations using Cat 5 Cable with an Auxiliary Output Board.
VM102 Master 6-Wire Cable Terminations
6 Wire Cable without Auxiliary Output
Diagrams for VM102 Master terminations using 6 Wire Telephone Cable without Auxiliary Output Board.
6 Wire Cable with Auxiliary Output
Diagrams for VM102 Master terminations using 6 Wire Telephone Cable with Auxiliary Output Board.
Master Station Terminal Functions
TC 2 Terminal Function
Explanation of the TC2 terminal's function, applicable only to Secure Masters (VM102-S).
TAMP 3K3 Terminals
Details on using TAMP 3K3 terminals for tamper switches with end of line resistors.
13.8V O-P Terminals
Description of 13.8V O-P terminals for powering auxiliary devices.
LOAD RES Terminals
Information on using LOAD RES terminals, including load resistor values and track cutting.
VR102 Room Station Installation
Room Stations in Timber Frame Walls
Instructions for installing VR102 Room Stations in timber frame walls, including cutout and fixing.
VR102 Room Station Installation and Load Resistor
Room Stations in Cavity Brick Walls
Procedure for installing VR102 Room Stations in cavity brick walls, similar to timber frame installations.
Load Resistor for Room Station Only Systems
Guidance on fitting a load resistor for Room Station Only systems and its placement.
VR102 Room Station Cable Terminations (Valet Cable)
Without Auxiliary Output Board
Diagram showing Valet Cable terminations for VR102 Room Station without Auxiliary Output Board.
With Auxiliary Output Board
Diagram showing Valet Cable terminations for VR102 Room Station with Auxiliary Output Board.
VR102 Room Station Cable Terminations (Cat 5 Cable)
Without Auxiliary Output Board
Diagram showing Cat 5 Cable terminations for VR102 Room Station without Auxiliary Output Board.
With Auxiliary Output Board
Diagram showing Cat 5 Cable terminations for VR102 Room Station with Auxiliary Output Board.
VR102 Room Station Cable Terminations (6 Wire Cable)
Without Auxiliary Output
Diagram showing 6 Wire Telephone Cable terminations for VR102 Room Station without Auxiliary Output.
With Auxiliary Output
Diagram showing 6 Wire Telephone Cable terminations for VR102 Room Station with Auxiliary Output.
VF103 Door Station Installation
Door Station in Brick Wall
Instructions for installing VF103 Door Stations in brick walls, including wall box and fascia mounting.
VF103 Door Station Cable Terminations
Using Valet Cable
Diagram showing Valet Cable terminations for VF103 Door Station, including relay connections.
Using Cat 5 Cable
Diagram showing Cat 5 Cable terminations for VF103 Door Station, including relay connections.
VR102 Room Station Cable Terminations (Cat 5)
Without Auxiliary Output Board
Diagram showing Cat 5 Cable terminations for VR102 Room Station without Auxiliary Output Board.
With Auxiliary Output Board
Diagram showing Cat 5 Cable terminations for VR102 Room Station with Auxiliary Output Board.
VR102 Room Station Cable Terminations (6 Wire)
Without Auxiliary Output
Diagram showing 6 Wire Telephone Cable terminations for VR102 Room Station without Auxiliary Output.
With Auxiliary Output
Diagram showing 6 Wire Telephone Cable terminations for VR102 Room Station with Auxiliary Output.
Voltage Output Wiring
Wiring Voltage Outputs
Explanation of 12V DC lock and chime voltage outputs, including warnings about load resistance.
Lock Output Functionality
Details on using the LK terminal for automatic gates or door strikes, and programming considerations.
Electric Lock Powering Options
Powering Lock from Door Station
Diagram and warning for powering an electric lock directly from the Door Station.
Powering Lock from Separate Supply
Diagram and note for powering an electric lock from a separate supply via a relay.
Specific Output Operation Scenarios
Operating Automatic Gates
Diagram showing how to operate automatic gates using the LK terminal and a relay.
Lock Operation Triggered by Chime
Diagram for operating a lock via a relay triggered by the chime function.
Alternative Door Station Wiring
4 and 5 Wire Operation
Explanation of 5-wire operation where the TC line may be omitted.
Diode Placement for 5-Wire Operation
Diagram showing diode placement for 5-wire operation when the TC line is omitted.
4-Wire Operation with Capacitors
4-Wire Operation Explanation
Explanation of 4-wire operation where COM2 and TC lines may be omitted.
Capacitor Placement for 4 Wire Operation
Diagram showing capacitor placement to compensate for 4-wire operation.
VF102 Door Station Installation
VF102 Cable Termination (Valet Cable)
Diagram showing Valet Cable terminations for VF102 Door Station, including optional relay.
VF102 Door Station Cable Terminations
Using Cat 5 Cable
Diagram showing Cat 5 Cable terminations for VF102 Door Station.
Using 6 Wire Telephone Cable
Diagram showing 6 Wire Telephone Cable terminations for VF102 Door Station.
Auxiliary Input Jack Type B Installation
Installation in Timber Frame Walls
Instructions for installing the Auxiliary Input Jack Type B in timber frame walls.
Installation in Cavity Brick Walls
Instructions for installing the Auxiliary Input Jack Type B in cavity brick walls.
Connection to Audio Source
Guidance on connecting audio sources like CD players or computers to the Input Jack Type B.
Input Jack Type B Connection Diagrams
8 Wire Systems Diagram
Diagram for connecting Input Jack Type B in 8-wire systems, showing jumper settings.
6 Wire Systems Diagram
Diagram for connecting Input Jack Type B in 6-wire systems, showing jumper settings.
Accessory Installation Procedures
Wireless Audio Transmitter Installation
Instructions for connecting and powering the Wireless Audio Transmitter.
Auxiliary Output Board Installation
Steps for fitting an Auxiliary Output Board to the Master Station.
Auxiliary Output Board at Room Station
Steps for fitting an Auxiliary Output Board to a Room Station.
Auxiliary Output Board Applications
Electric Door Strike Application
Diagram showing application of Auxiliary Output Board for an electric door strike.
Automatic Gates Application
Diagram illustrating application of Auxiliary Output Board for automatic gates.
Power Supply Installation
Power Supply Current Rating
Guide to calculating power supply current rating based on system components and their consumption.
Connection to Master System
Instructions for connecting the power supply to the Master Station, including polarity.
Power Supply Connection for Room Station Only Systems
Acceptable Loop Wiring (Figure A)
Diagram A illustrating acceptable loop wiring for power supply connection in Room Station only systems.
Unacceptable Loop Wiring (Figure B)
Diagram B showing unacceptable loop wiring for power supply connection in Room Station only systems.
VM102 Master Station Radio and Clock Adjustments
Setting the Clock
Procedure for setting the clock on the VM102 Master station.
Setting the Radio
Instructions for tuning and setting presets for the FM radio on the VM102 Master.
VM102 Master Station Programming
Master Station Coding
Procedure for allocating single or double digit numbers to the Master Station for select calling.
VM102 Master Station Configuration
Keypad Backlighting Control
Information on toggling the keypad backlighting on and off on the VM102 Master.
Selecting Six Wire Operation Mode
Steps to select 6-wire mode on Room Stations and ensuring the Master remains in 8-wire mode.
VM102 Master Station Adjustments
Preset Intercom Audio Level Settings
Procedure for adjusting preset intercom audio levels, speaker volume, and chime levels.
Microphone Gain Adjustment
Guide to adjusting microphone gain using a trim-pot, including resistance measurement.
VR102 Room Station Programming
Room Station Coding
Procedure for allocating single or double digit numbers to Room Stations for select calling.
VR102 Room Station Configuration
Keypad Backlighting
Information on toggling keypad backlighting on and off for VR102 Room Stations.
Selecting Six Wire Mode
Procedure for selecting 6-wire mode on VR102 Room Stations, noting omitted music lines.
VR102 Room Station Adjustments
Microphone Gain Adjustment
Guide to adjusting microphone gain on VR102 Room Stations using a trim-pot and resistance measurement.
VF103 Door Station Programming and Adjustments
VF103 Door Station Adjustments
Details on adjusting speaker volume, chime volume, and microphone gain on VF103 Door Stations.
Voltage Output Wiring
Wiring Voltage Outputs
Explanation of 12V DC lock and chime voltage outputs, including warnings about load resistance.
Lock Output Functionality
Details on using the LK terminal for automatic gates or door strikes, and programming considerations.
VF102 Door Station Programming and Adjustments
VF102 Door Station Adjustments
Details on adjusting speaker volume, chime volume, and microphone gain on VF102 Door Stations.
Input Jack Type B and Wireless Transmitter Setup
Input Jack Type B Setup
Instructions for setting up the Input Jack Type B and jumper configurations for 6 or 8 wire systems.
Wireless Audio Transmitter Setup
Guide to setting up the Wireless Audio Transmitter by tuning the intercom radio to specific FM frequencies.
System One Terminal Functions
TC1 Master Station Terminal Function
Description of TC1 terminal function at Master Station for security voice and communication.
TC2 Master Station Terminal Function
Description of TC2 terminal function at Master Station, not for security voice.
TC Room and Door Station Terminal Function
Description of TC terminal function at Room and Door Stations for communication and chime.
VLC Terminal Function
Explanation of VLC terminal function, including voltage levels for different buttons.
Terminal Function Details
VLC Input/Output Voltage Levels
Table detailing VLC output voltage levels with reference to 1/2 supply for various buttons.
SHLD Terminal Function (Master Station)
Description of SHLD terminal function at Master Station for shields and interference protection.
SHLD Terminal Function (Other Stations)
Description of SHLD terminal function at other stations for continuity and termination.
COM1 and COM2 Terminal Functions
Explanation of COM1 and COM2 terminals for balanced audio, communication, chime, and security voice.
MUS1 and MUS2 Terminal Functions
Explanation of MUS1 and MUS2 terminals for balanced audio, music, and monitoring.
Master Station Terminal Descriptions
AUX Terminal Function
Description of AUX terminal function for activating programmed relays on output boards.
Master Station Power and Battery Terminals
Details for BATT, 13.8V IP, and 13.8V OP terminals at the Master Station.
Master Station Antenna and Load Resistor Terminals
Description of FM, AM antenna, and Load Resistor terminals at the Master Station.
Master Station Security Output Terminals
Explanation of STR-, STR+, SIR-, SIR+, and TAMP 3K3 terminals for security features.
New Room Station Features
Digital Volume Control
Description of digital volume control on new Room Stations and disabling audible tone.
Microphone Gain Adjustment
Explanation of fixed microphone gain and how to decrease it by cutting a link.
Back Housing Options
Information on new surface mount or recess mount back housing options for Room Stations.
Fascia Options
Details on Room Stations being supplied without fascias, which are sold separately.
Keymat Update
Notes on the updated keymat with extra volume keys and a key symbol for lock output.
New Door Station Features
Room Station Assembly Overview
Diagram showing the assembly of a Room Station, including PCB, keymat, and metal plate.
Door Station Models and Wiring
Description of new S1-FD and S1-FDC Door Station models, including camera and colour options.
Wiring with Camera
Wiring details for Door Stations with cameras, including extra coax and TC2 terminal usage.
Door Station Features and Options
Door Station LED Lighting
Explanation of white LEDs for subject lighting and how to disable them.
Mounting Orientation
Information on configuring door station mounting orientation for vertical installation.
Door Station Speaker
Details on the mylar cone speaker fitted to Door Stations for outdoor conditions.
Door Station Microphone Gain
Explanation of fixed microphone gain for Door Stations and how to decrease it.
Door Station Back Housing
Information on recess mount back boxes for Door Stations and availability of surface mount options.
Door Station Fascias
Notes on Door Stations being supplied with fascias, and limited colour variations.
Desktop Station Introduction
Desktop Station Placement
Description of the desktop station designed for desktop placement rather than wall mounting.
Auxiliary Audio Input
Details on the auxiliary audio input for listening to music from MP3 players or PCs.
Desktop Station Wiring
Wiring specifications for the desktop station using Cat5 cable and RJ45 wall plate.
New Master Station Features
New Master Station Models
Availability of S1P Master Station models with or without LCD display.
New Master Station AM/FM Radio
Details on the single PCB module for AM/FM radio and the new alarm function.
New Master Station Back Housing
Description of the modified plastic back box for the new Master Station front.
Master Station Video and Wiring Features
Master Station Video Display
Information on the S1P-MV LCD display accepting video from cameras and activation times.
Using Display for Alternative Video Source
Procedure for using the video display with alternative sources like TV tuners or DVD players.
Master Station Wiring Updates
Notes on wiring changes for Cat5 cable colour coding and TC2 terminal usage for video display.
New Master Station Control Features
Digital Volume Control
Description of the digital volume control on the new Master Station with audible feedback.
Microphone Gain Reference
Reference to Room Station section for details on Master Station microphone gain.
Lock Control
Information on the lock output terminal and relay contacts on the Master Station.
Keymat Changes
Details on keymat changes including Volume Up/Down keys and the CLEAR button.
Need help?
Do you have a question about the S1-M and is the answer not in the manual?
Questions and answers