NorthStar 952X Installation Manual
Gps chart navigators
Hide thumbs
Also See for 952X:
- Operator's manual (206 pages) ,
- Installation manual (80 pages) ,
- Addendum operator's manual (12 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Troubleshooting
Related Manuals for NorthStar 952X
Summarization of Contents
Introduction to Northstar 951/952 Installation
Servicing the Unit
Explains the process for returning the Northstar 951/952 unit for factory repair or service.
Returning a Unit for Service
Details the procedure for obtaining an RMA and shipping the Northstar 951/952 unit for repair.
Installing the Northstar 951/952 Unit
Safety Considerations for Installation
Highlights critical safety precautions and warnings during the installation process.
Ordering Information for Parts
Provides contact details for ordering spare parts or replacement components for the unit.
System Overview
Provides a general overview of the Northstar 951/952 unit and its components.
Installation Considerations and Best Practices
Covers essential factors for a proper installation, including bench-testing and antenna placement.
Using DGPS with AN150 and 8410 ACU
Details the connection and setup for DGPS systems using the AN150 antenna and 8410 ACU.
Using the AN205-P DGPS Antenna
Explains mounting requirements for the AN205-P combination GPS/DGPS antenna.
Choosing a System Location
Provides guidance on selecting an optimal mounting location for the 951/952 unit.
Flush and Yoke-Mounting Procedures
Details the recommended drilling dimensions and clearance for flush and yoke mounting the unit.
Wiring the Northstar 951/952 Unit
Covers the electrical power requirements and internal fuse protection for the unit.
Installing the Antenna
Details antenna choices, mounting locations, wiring, and troubleshooting for AN150 and AN205-P antennas.
Powering Up the Northstar 951/952 Unit
Guides on inserting chart cartridges, powering on the unit, and initial system checks.
Testing and Troubleshooting the Northstar 951/952
Covers installation testing, common problems, and specific troubleshooting for display, system, and antenna issues.
Troubleshooting GPS/DGPS Antenna Installation
Provides detailed steps for troubleshooting GPS and DGPS antenna signals and connections.
Interfacing the Northstar 951/952 with Other Equipment
Interfacing the Unit Overview
Introduces NMEA 0183 and RS-232 interfaces for connecting the unit to marine electronics.
Connector Pin Wiring Details
Lists wire designations for the interface connector, accessed via the PORT SETUP OPTIONS screen.
Interface Connector Pin Assignments
Details the pin assignments for the unit's interface connector, including NMEA and RS-232 ports.
200 PPNM Output Functionality
Explains the open-collector transistor output for 200 pulses per nautical mile.
Configuring NMEA Output Ports
Guides on programming NMEA 0183 sentences for output from the unit's ports.
NMEA Port Setup Options
Details options for output format, talker ID, and LL precision for NMEA ports.
Setting the NMEA Output Format
Explains how to select NMEA output formats like NMEA 0180, 0183 V2.1, and DATAMARINE CDX.
About NMEA 0183 and RAY 0183 Standards
Explains the NMEA 0183 standard for marine electronics communication and the RAY 0183 format.
Displaying NMEA Output Sentences
Shows how to view and select available NMEA 0183 sentences for output from the unit.
Controlling NMEA Output Sentences
Guides on enabling or disabling specific NMEA 0183 sentences for transmission.
Choosing the NMEA 0183 Talker ID
Explains how to set the talker ID to identify the unit as a GPS or Loran navigator.
Setting NMEA 0183 Lat/Lon Precision
Allows adjustment of output precision for latitude/longitude in NMEA 0183 sentences.
Changing the NMEA Output Rate
Allows adjustment of the NMEA data output interval from 1 to 999 seconds.
Changing NMEA 0183 Waypoint ID
Enables display of waypoint names instead of numbers for compatibility with other devices.
Setting the NMEA 0183 Checksum
Provides the option to disable the NMEA 0183 checksum for compatibility with older devices.
Selecting Independent NMEA Output Datum
Allows adjustment of output position for NMEA 0183 ports to specific geodetic datums.
Connecting to Other Northstar Units
Details how to connect two units to transfer waypoints and routes using the Waypoint Database Sharing Kit.
Connecting the Two Units
Explains the procedure for connecting two Northstar units for data transfer, including required parts.
Assembling the Data Transfer Cable
Provides steps for preparing and assembling the cable for connecting two Northstar units.
Connecting Cable Ends to Units
Details how to connect the assembled cable ends to the 941/951/952 units.
Connecting to External Differential Correction Sources
Explains how to connect external Northstar beacon receivers (8800, 8400, 8401) to the 951/952 via RS-232.
Connecting to Northstar 800 Series Loran
Details how to connect a Northstar 800 series loran for TD data and waypoint transfer.
Northstar 800 Series Port Connections
Specifies wiring for connecting Northstar 800 ports A and B to the 951/952 ports.
Connecting Other Devices to the Northstar 951/952
Details connections for Yeoman chart plotters, radar devices, and alarm honk configuration.
Setting the Anchor-Watch Alarm to Honk
Provides step-by-step instructions to configure the anchor-watch alarm for audible honking.
Setting All Alarms to Honk
Guides on configuring the unit to produce a honking sound for all system alarms.
Configuring the RS-232 Port
Covers RS-232 settings for SC-104 corrections, PC connections, diagnostics, and port off.
RS-232 Diagnostic Option
Explains the diagnostic option for factory use only, advising against its activation.
Using the RS-232 Port Off Setting
Describes the 'port off' setting for disabling RS-232 input/output functions when not needed.
Ordering Software Updates for Northstar 951/952
Information for dealers and end users on obtaining and installing software updates.
Appendix A: Technical Specifications
951/952 Power and GPS Receiver Specifications
Details power source, consumption, GPS receiver type, sensitivity, accuracy, and dynamics.
951/952 Interfacing Capabilities
Lists NMEA I/O ports, RS-232 port, waypoint transfer, and software upload capabilities.
Physical and Environmental Features
Describes the display screen characteristics and operating temperature/humidity ranges.
IEC Compliance Standards
Lists standards for immunity to electromagnetic environment and rain testing for the Northstar 951.
Internal DGPS Receiver Specifications
Provides details on signal processing, frequency range, tuning resolution, and acquisition time.
Data Processing and Power Requirements
Details data processing methods like demodulation and power consumption of the unit.
AN150 Active GPS Antenna Specifications
Lists height, diameter, and weight for the AN150 Active GPS Antenna.
8410 Antenna Coupling Unit Specifications
Provides specifications for the 8410 ACU, including height, diameter, weight, and whip antenna.
Combination GPS/DGPS Antenna Specifications
Lists specifications for the combo antenna: frequency, polarization, impedance, and power handling.
Need help?
Do you have a question about the 952X and is the answer not in the manual?
Questions and answers