Related Manuals for Unitor AG-PRO 4
Summary of Contents for Unitor AG-PRO 4
-
Page 1: Spare Parts List
Instruction manual & spare parts list AG-PRO 7 AG-PRO 5 AG-PRO 4 AG-PRO SERIES AIR DRIVEN ANGLE GRINDERS Revision date 05/2008... - Page 2 1.General Safety and Operation Instruction 1. Unpacking When unpacking this product, carefully inspect for any damage that may have occurred during transit. Make sure any loose fittings, bolts, etc., are tightened before putting this product into service. 2. This product is a part of a high-pressure system and the following safety precautions must be followed at all times along with any other existing safety rules.
- Page 3 16. Keep all nuts, bolts and screws tight and ensure equipment is in safe working condition. 17. Do not put hands near or under moving parts. 18. Speed Adjustment The grinder should never be used to set torque. Use a torque wrench to set the torque. Are equipped with regulators for speed adjustment.
- Page 4 2. Information of Vibration Level (1)The vibration level at the handle is about¡G 1.792 ~ 5.706 (2)Reference standard¡GEN 28662-1. 3. Information of Temperatures (1)The temperatures at the handle (8 hours/Operation) is ¢J. 4.Safety Information Rated rotational speed of the spindle is 5000 ~ 70000 R.P.M. 5.
-
Page 5: Maintenance Instruction
6. Explanations Of Warning Signs used For This Tool The operator’s Eye protection must be Hearing protection must Instruction must be read used or safety glasses be worn before work starts worn Direction of rotation Engine oil Fuel Reverse function 7. - Page 6 Disconnect the grinder from the air supply before lubricating. 1. Disconnect the die grinder from the air supply. 2. Turn the die grinder upside down. 3. Simultaneously (at the same time), pull the trigger and pour a teaspoon of oil in the air inlet. Then, push the forward and reverse button in both directions.
- Page 7 General Trouble shooting Guide Symptom Possible Cause(s) Corrective Action Tool runs slowly or 1. Grit or gum in tool. 1.Flush the tool with air tool oil, gum solvent, or will not operate an equal mixture of SAE # 10 motor 011 and kerosene.
- Page 8 UNITOR AG-PRO 4 B SPECIFICATIONS： ＊GRINDING WHEEL ----------------- 4” ＊FREE SPEED --------------- 13,600 RPM ＊AIR PRESSURE --------------- 90 PSI ＊HOSE SIZE -------------------------- 3/8” ID ＊AIR INLET -------------- 1/4” PT(NPT) PARTS NO. DESCRIPTION Q‘TY PARTS NO. DESCRIPTION Q‘TY 752281 HANDLE (LEVER TYPE)
- Page 9 UNITOR AG-PRO 4 B Revision date 05/2008...
- Page 10 UNITOR AG-PRO 5 SPECIFICATIONS： ＊GRINDING WHEEL ----------------- 5” ＊FREE SPEED --------------- 10,900 RPM ＊AIR PRESSURE --------------- 90 PSI ＊HOSE SIZE -------------------------- 3/8” ID ＊AIR INLET -------------- 1/4” PT(NPT) PARTS NO. DESCRIPTION Q‘TY PARTS NO. DESCRIPTION Q‘TY 752281 HANDLE (LEVER TYPE)
- Page 11 UNITOR AG-PRO 5 Revision date 05/2008...
- Page 12 UNITOR AG-PRO 7 SPECIFICATIONS： ＊GRINDING WHEEL ----------------- 7” ＊FREE SPEED ----------------- 7,600 RPM ＊AIR PRESSURE --------------- 90 PSI ＊HOSE SIZE -------------------------- 1/2” ID ＊AIR INLET -------------- 3/8” PT(NPT) PART NO. DESCRIPTION Q‘TY PART NO. DESCRIPTION Q‘TY 752380 HANDLE (LEVER TYPE)
- Page 13 UNITOR AG-PRO 7 Revision date 05/2008...
-
Page 14: Spare Parts List
Fraser/surrey Gaspe Gros Caouna Halifax Hamilton Harbour Grace Holyro od Kitimat Long Pond Marytown Montreal N anaimo New Westminster Bc Pictou/halifax Pointe Aux Pic.quebec Port Alfred Port Cartie r Port Colborne Port Hawkesbury Port Mellon Port M oody Instruction manual Port Of Quebec Port Weller Powell River Prince Rupert Roberts Bank Saint Jo hn Sarnia, Ontario Sept Iles Seven Islands S orel Souris/...
Need help?
Do you have a question about the AG-PRO 4 and is the answer not in the manual?
Questions and answers