Table of Contents
Related Manuals for Hydrotek SS Series
Summary of Contents for Hydrotek SS Series
- Page 1 OPERATION & MAINTENANCE MANUAL IMPORTANT: CAUTION! TO REDUCE RISK OR INJURY, READ OPERATING INSTRUCTIONS CAREFULLY BEFORE USING ULTIMATE LINE POWER WASHERS CN SERIES CP SERIES CW SERIES HP SERIES HX SERIES SC SERIES SS SERIES © Hydro Tek . 1/2007...
- Page 2 XBTIJOH!BDDFTTPSJFT HYDRO TWISTER ® SURFACE CLEANERS The ANT3C Contractor Series HYDRO The ANT38 HYDRO TWISTER is a unique surface TWISTERS are the proven choice for cleaner with a 38” cleaning path. The impressive size and professional surface cleaning with three construction allows the operator to maneuver and clean options for your cleaning needs.
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..........................4 Statement of Warranty SAFETY WARNINGS ........................... 5-6 Electrical Precautions Fire Precautions Ventilation Precautions Spray Injection Precautions Personal Hazard Precautions OPERATING INSTRUCTIONS ......................7-8 Before Start Up Operation Shut Down & Antifreeze Protection SYSTEM INFORMATION ......................... 9 Chassis and Trailer Assembly Power System .......................... -
Page 4: Introduction
INTRODUCTION NO- NONSENSE GUARANTEE: INTRODUCTION: Hydro Tek Systems, Inc. (Hydro Tek) promises to repair THANK YOU: The employees and management of Ultimate and Proline washers if defective in materials or HYDRO TEK SYSTEMS, INC. thank you for selecting workmanship for one year from the date of original retail our products. -
Page 5: Safety Warnings
To locate service, call the factory and grounded. Do not modify the plug provided with the ask for technical services or go to www.hydrotek.us product, do not cut off the ground pin - if it will not fit the 3.You may also ship the defective part freight prepaid... -
Page 6: Ventilation Precautions
IMPORTANT SAFETY WARNINGS: SAVE THESE INSTRUCTIONS 2. Fill the diesel burner fuel tank with #2 diesel fuel or persons. Use only 48" long wands on machines produc- kerosene. NEVER use gasoline. Do not confuse gaso- ing over 3000 psi. Also, only use straight wands or line and fuel oil tanks. -
Page 7: Operating Instructions
OPERATING INSTRUCTIONS BEFORE START UP: power switch on. If unit is equipped with auto-start, keep all power switches off when left unattended. 1. Read all instructions before using this product. (Unit will only turn on when trigger gun is pulled.) Unit 2. -
Page 8: Washing Techniques
OPERATING INSTRUCTIONS long - More Than Five Minutes - friction created by the with the chemical system on the equipment; either down movement of the water will begin to heat the water at a stream or high pressure depending on the system you rapid rate. -
Page 9: System Information
SYSTEM INFORMATION CHASSIS & TRAILER ASSEMBLY: generator. A dedicated breaker of sufficient ampere rating should To maintain the appearance of the machine use stainless be installed by an electrician. Refer to the chart above for steel cleaner on the stainless steel panels. electrical requirements: (208 Volt is acceptable, but unit Check tire air pressure. -
Page 10: Pumping System
SYSTEM INFORMATION GENERATOR: completely thawed UNLOADER AND PRESSURE RELIEF Some self-contained Hot Water Units are equipped with VALVE: The unloader valve is preset at the a 115 volt generator to power the diesel factory to govern the proper output pressure of burner. -
Page 11: Heating System
SYSTEM INFORMATION and follow all safety instructions on the detergent label. clean more effectively. Do not use deionized water through WATER SUPPLY: An adequate water supply must be the coil on a hot water machine or coil corrosion will result. maintained to the pump at all times. -
Page 12: Pressure Delivery System
SYSTEM INFORMATION DIAGNOSTIC LIGHT: The burner diagnostic light on the battery on the SS/SM Series. The engine has a 15 to the rocker switch, (if equipped), can help in determining 16 amp charging system which keeps the battery charged problems with the burner. The red light indicates that which runs the burner. - Page 13 SYSTEM INFORMATION your machine was designed for. The orifice, or hole, of the sure washer. The sand is mixed with the water at the sand nozzle will begin to get larger as the nozzle becomes worn. head in a tungsten carbide nozzle. For optimum performance, replace the spray nozzle to A vacuum is created in the sand nozzle which draws a maintain the full output pressure of your machine.
-
Page 14: Gun/Wand Assembly - Trigger Gun, Wand, & Quick Coupler Nozzles - Spray Nozzles And Steam Nozzle Accessories - Wet Sandblaster, Turbo Nozzle, Hoses And Reels, Wands, Injectors
SYSTEM INFORMATION age of both discharge and inlet hoses. To keep the hose damaged. Not recommended for solids or gravel over .25" from unreeling, lock the drum in place and secure the gun diameter. Do not run dry or run flammable fluid into the or the end of the hose or it may drag on the road. -
Page 15: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE PROBLEM PROBABLE CAUSE* REMEDY Power System: Gasoline or Diesel Engine Driven Engine will not start or crank over. Battery dead. Charge or replace battery, add electrolyte if battery is new. Dirty battery connection. Clean connections. Battery cables disconnected. Connect or replace damaged cables. - Page 16 TROUBLE SHOOTING GUIDE PROBLEM PROBABLE CAUSE* REMEDY Inlet injection will not siphon chemical. Check valve in strainer clogged. Clean or replace. Rinse after each use. Chemical valve not open or clogged. Open chemical valve or clean. Strainer not submerged in solution. Submerge strainer and replenish chemical.
-
Page 24: Service/Maintenance Information
MAINTENANCE INFORMATION PREVENTATIVE MAINTENANCE: equipment. Contact your Hydro Tek dealer for mainte- nance. A small investment in preventative maintenance will While your pressure washer has been produced with add many hours to the life of your pressure washer. quality materials and craftsmanship, you as the owner have Perform maintenance more often under severe conditions.
Need help?
Do you have a question about the SS Series and is the answer not in the manual?
Questions and answers