Lexicon MPX 1 V1.10 - UPGRADE Manual page 2

The following general safety precautions must be observed during all phases of operation, service and repair of this
instrument. Failure to comply with these precautions, or with specific warnings elsewhere in these instructions
violates safety standards of design manufacture and intended use of the instrument. Lexicon assumes no liability
for the customer's failure to comply with these requirements.
GROUND THE INSTRUMENT
To minimize shock hazard the instrument chassis and cabinet must
be connected to an electrical ground. The instrument is equipped
with a three-conductor AC power cable. The power cable must either
be plugged into an approved three-contact electrical outlet or used
with a three-contact to two-contact adapter with the grounding wire
(green) firmly connected to an electrical ground (safety ground) at
the power outlet. The power jack and mating plug of the power cable
meet International Electrotechnical Commission (IEC) safety stan-
dards.
DO NOT OPERATE IN AN EXPLOSIVE
ATMOSPHERE
Do not operate the instrument in the presence of flammable gases
or fumes. Operation of any electrical instrument in such an environ-
ment constitutes a definite safety hazard.
KEEP AWAY FROM LIVE CIRCUITS
Operating personnel must not remove instrument covers. Compo-
nent replacement and internal adjustments must be made by quali-
fied maintenance personnel. Do not replace components with power
cable connected. Under certain conditions, dangerous voltages may
exist even with the power cable removed. To avoid injuries, always
disconnect power and discharge circuits before touching them.
DO NOT SERVICE OR ADJUST ALONE
Do not attempt internal service or adjustment unless another person,
capable of rendering first aid and resuscitation, is present.
DO NOT SUBSTITUTE PARTS OR MODIFY
INSTRUMENT
Because of the danger of introducing additional hazards, do not
install substitute parts or perform any unauthorized modification to
the instrument.
DANGEROUS PROCEDURE WARNINGS
Warnings, such as the example below, precede potentially danger-
ous procedures throughout this manual. Instructions contained in the
warnings must be followed.
WARNING
Dangerous voltages, capable of causing death, are present in
this instrument. Use extreme caution when handling, testing
and adjusting.
3 Oak Park
Bedford MA 01730-1441
781-280-0300
Fax: 781-280-0490
© Lexicon, Inc. 1997
SAFETY SUMMARY
General definitions of safety symbols used on equipment or in
manuals.
WARNING
CAUTION
NOTE:
Electrostatic Discharge (ESD) Precautions
The following practices minimize possible damage to ICs
resulting from electrostatic discharge or improper inser-
tion.
• Keep parts in original containers until ready for use.
• Avoid having plastic, vinyl or styrofoam in the work
area.
•. Wear an anti-static wrist-strap.
• Discharge personal static before handling devices.
• Remove and insert boards with care.
• When removing boards, handle only by non-conduc-
tive surfaces and never touch open-edge connectors
except at a static-free workstation.*
• Minimize handling of ICs.
•. Handle each IC by its body.
• Do not slide ICs or boards over any surface.
• Insert ICs with the proper orientation, and watch for
bent pins on ICs.
• Use anti-static containers for handling and transport.
*To make a plastic-laminated workbench anti-static, wash with
a solution of liquid detergent, and allow to dry without rinsing.
SAFETY SYMBOLS
Instruction manual symbol: the product will be
marked with this symbol when it is necessary
for the user to refer to the instruction manual in
order to protect against damage to the instru-
ment.
Indicates dangerous voltage. (Terminals fed
from the interior by voltage exceeding 1000
volts must be so marked.)
The WARNING sign denotes a hazard. It calls
attention to a procedure, practice, condition or
the like which, if not correctly performed or
adhered to, could result in injury or death to
personnel.
The CAUTION sign denotes a hazard. It calls
attention to an operating procedure, practice,
condition or the like which, if not correctly
performed or adhered to, could result in dam-
age to or destruction of part or all of the
product.
The NOTE sign denotes important informa-
tion. It calls attention to procedure, practice,
condition or the like which is essential to
highlight.
CAUTION