Related Manuals for Mono ML
Summary of Contents for Mono ML
- Page 1 English Original Instructions Installation, Operation and Maintenance Instructions MM / ML Range OMMP/014/01 Rev 5, December 2009...
-
Page 2: Spares & Service Contact Details
(08) 9479 0400 Darwin (08) 8984 3099 (08) 8947 0540 Tasmania 0417 345 814 (03) 6330 2051 E-mail ozsales@mono-pumps.com Mono New Zealand Spares & Service +64 (0)9 829 0333 E-mail info@mono-pumps.co.nz Monoflo USA Spares & Service +1 713 466 7999 E-mail inquire@monoflo.com... - Page 3 If there is any doubt as to the essential that a dry run protection device be fitted. suitability of the equipment please contact Mono This must shut the pump down immediately should a Pumps Limited before commencing with installation dry run situation occur.
- Page 4 The use of replacement parts that are not When fitting drives, couplings, belts, pulleys and manufactured by or approved by Mono Pumps Limited guards to a pump or pump unit it is essential that may affect the safe operation of the pump and it may...
-
Page 5: Ec Declaration Of Conformity
Mr C. Q. Griffiths - Engineering Services Manager. for Mono Pumps Limited, Martin Street, Audenshaw, Manchester England, M34 5JA Index Issued – December 2009... -
Page 6: Section 1, Page 1 Issued - October 2009
In common with other items of process plant a pump described above, confirmation of the installation must be installed correctly to ensure satisfactory and must be agreed with Mono Pumps Limited. All the safe operation. The pump must also be maintained pipework should be independently supported. - Page 7 DUTY CONDITIONS work on. Pumps should only be installed on duties for which Mono Pumps Limited have specified the materials of PRESSURE RELIEF VALVES AND NON-RETURN construction, flow rates, pressure, temperature, VALVES speed etc.
- Page 8 DIRECTIONS OF ROTATION of the seal. This should be provided in line with the seal manufacturers instructions. BEFORE THE DIRECTION OF ROTATION IS CHANGED, MONO PUMPS LIMITED MUST BE 2.4. GUARDS CONSULTED SO THAT THE SUITABILITY OF THE PUMP CAN BE CONFIRMED WHEN In the interests of safety, and in accordance with the OPERATING ON THE NEW DUTY.
- Page 9 Installation, Operation & Maintenance Instructions WARNING/CONTROL DEVICE BP LC2 / Mobilgrease XHP 222 or their equivalent must be used for replenishment. Prior to operating the pump, if any warning or control devices are fitted these must be set in accordance PUMP UNITS with their specific instructions.
- Page 10 Installation, Operation & Maintenance Instructions Acid wash @ 50°C for 20 mins 2.13 ACCESS PORTS Water rinse @ 80°C for 20 mins Where access ports are fitted then the following CIP flow rates (hence pump speeds) should be steps must be followed prior to removal: maximised to achieve highest level of cleanability.
- Page 11 The use of replacement items that are not approved becomes difficult to achieve. by or manufactured by Mono Pumps Limited may affect the safe operation of the pump and it may 2.15.3...
- Page 12 Installation, Operation & Maintenance Instructions RECOMMENDED LIFTING POINTS CHOKE CHOKE 120° CHOKE CHOKE 120° CHOKE CHOKE 120° CHOKE CHOKE Section 1, Page 7 Issued – August 2009...
- Page 13 NOTE: Weights are for guidence purpose only. Please refer to the documetation issued with your pump or spares. M Range Pump Weight (kg) Model Motorised MM/ML All wear parts are less than 5kg Section 1, Page 8 Issued – October 2009...
-
Page 14: Diagnostic Chart
Diagnostic Chart NO DISCHARGE 1. 2. 3. 7. 26. 28. 29. LOSS OF CAPACITY 3. 4. 5. 6. 7. 8. 9. 10. 22. 13. 16. 17. 21. 22. 23. 29 IRREGULAR DISCHARGE 3. 4. 5. 6. 7. 8. 13. 15. 29. PRIMING LOST AFTER START 3. -
Page 15: Section 3, Page 1
Drawing Reference Numbers DRG. DESCRIPTION BODY NAMEPLATE 1050 MECHANICAL SEAL BARREL STATOR END COVER ROTOR COUPLING SHAFT SEAL HOUSING 6650 SEAL COLLAR P100232S TAPER PLUG S110870P SEAL RING A112161F CAP SCREW A112201F CAP SCREW A111101F CAP SCREW K113242F BOLT N113102F R101082F DRIVE SCREW W113252F... - Page 16 Dimantling & Assembly Diagrams Section 4, Page 1 Issued – November 2002...
-
Page 17: Section 4, Page 2
Dimantling & Assembly Diagrams Section 4, Page 2 Issued – December 2000... - Page 18 Dimantling & Assembly Diagrams Section 4, Page 3 Issued – December 2000...
- Page 19 Dimantling & Assembly Diagrams Section 4, Page 4 Issued – December 2000...
- Page 20 Dimantling & Assembly Diagrams Section 4, Page 5 Issued – December 2000...
- Page 21 Dimantling & Assembly Diagrams Section 4, Page 6 Issued – December 2000...
- Page 22 Dimantling & Assembly Diagrams Section 4, Page 7 Issued – December 2000...
- Page 23 Dimantling & Assembly Diagrams Section 4, Page 8 Issued – December 2000...
- Page 24 Dimantling & Assembly Diagrams Section 4, Page 9 Issued – December 2000...
- Page 25 Dimantling & Assembly Diagrams Section 4, Page 10 Issued – December 2000...
- Page 26 Dimantling & Assembly Diagrams Section 4, Page 11 Issued – December 2000...
-
Page 27: Exploded Views
Exploded Views Section 4, Page 12 Issued – December 2000... - Page 28 PO Box 71-021, Fremlin Place, Avondale Auckland 7, New Zealand T. +64 (0)9 829 0333 E. info@mono-pumps.co.nz Asia Mono Pumps Ltd, No. 500 YaGang Road Lujia Village, Malu, Jiading District Shanghai 201801, P.R. China T. +86 (0)21 5915 7168 E. monoshanghai@nov.com...
Need help?
Do you have a question about the ML and is the answer not in the manual?
Questions and answers