Advertisement
Table of Contents
- 1 Table of Contents
- 2 For the Installer
- 3 Sample bin and Machine Combinations
- 4 For the Installer
- 5 FOR the INSTALLER: Location
- 6 For the Plumber
- 7 For the Installer
- 8 For the Electrician
- 9 Initial Start up
- 10 Cleaning & Sanitizing
- 11 Sensor Maintenance
- 12 Air Cooled Maintenance
- 13 Bearing Maintenance
- 14 Auger Maintenance
- 15 REMOVAL and REPLACEMENT: bin Controls
- Download this manual
See also:
Installation Manual
Advertisement
Table of Contents
Related Manuals for Scotsman NME654AS-1
Summarization of Contents
Introduction and Troubleshooting
What to Do Before Calling for Service
Provides troubleshooting steps for when the ice machine is off or not making ice.
Installer Guidelines
NME Dispenser Applications
Details kits and compatibility for using NME models with various ice and ice-beverage dispensers.
Installation Limitations
Specifies environmental limits for air temperature, water temperature, and water pressure for installation.
Specifications: Ice Machine
Lists model numbers, dimensions, electrical, ice type, condenser, and refrigerant charge for the ice machines.
Installation Location and Bin Setup
Optimal Installation Location
Guidance on selecting a location with adequate space for service, air circulation, and avoiding adverse conditions.
Storage Bin Installation
Instructions for tipping, leveling, and positioning the storage bin before placing the ice machine on top.
Ice Machine Placement and Securing
Steps for lifting, aligning, and securing the ice machine onto the storage bin, including removing shipping blocks.
Water Quality and Limitations
Recommendations for water treatment, filtration, and conductivity limits for optimal ice production and machine life.
Plumbing Requirements
Water Inlet Connections
Details on connecting cold potable water using copper tubing and installing a hand valve for both air and water-cooled models.
Drainage Connections
Instructions for connecting drains for air-cooled and water-cooled models, including tubing pitch and vent requirements.
Water Cooled Model Drains
Specific requirements for connecting a separate condenser drain for water-cooled ice machines.
Storage Bin Drainage
Guidance on installing a gravity-type drain for the storage bin, with insulation recommended.
Electrical Installation and Checks
Electrical Connections and Safety
Details on connecting power, checking the nameplate, grounding, and ensuring compliance with electrical codes.
Final Installation Check List
A comprehensive checklist for installers to verify correct installation of the ice machine and bin.
Initial Start Up Procedure
Pre-Start Inspection Checklist
Steps to inspect the machine for proper installation, loose parts, and unobstructed fan movement before powering on.
Machine Startup Sequence
Procedure for turning on the machine, checking water flow, observing component operation, and verifying ice production.
Water Level Adjustment
Guidance on checking and adjusting the water level in the reservoir using the float arm for correct ice making.
Cleaning and Sanitizing Procedures
In-Place Ice Making System Cleaning
Detailed steps for cleaning the ice making system using a specific cleaner, including draining and rinsing.
Sanitizing the Ice Making System
Instructions for sanitizing the ice making system using a bleach solution, following similar steps to cleaning.
Storage Bin Cleaning and Sanitizing
Steps for washing, rinsing, and sanitizing the interior of the ice storage bin after ice removal.
Sensor Maintenance
Ice Level Sensor Cleaning
Procedure for cleaning the bin control sensors located at the base of the ice chute to ensure proper function.
Water Level Probe Cleaning
Instructions for removing and cleaning the water level probe in the reservoir to remove mineral build-up.
Air Cooled Condenser Maintenance
Condenser Cleaning Process
Steps to clean the air-cooled condenser by removing panels, using vacuum or coil cleaner, and checking for internal clogging.
Bearing Maintenance Procedures
Bearing Inspection and Lubrication
Guidance on checking bearing grease levels and lubricating the bearing using specific Scotsman parts.
Auger Maintenance
Auger and Evaporator Cleaning
Steps for removing and cleaning the auger and evaporator, especially in areas with high mineral content water.
Removal and Replacement Procedures
Bin Controls (Ice Level Sensors)
Detailed steps for removing and reinstalling the ice level sensors and their electrical connections.
Reservoir Removal and Reassembly
Instructions for disconnecting and removing the water reservoir, including the float assembly and water sensor.
Need help?
Do you have a question about the NME654AS-1 and is the answer not in the manual?
Questions and answers