Advertisement
Quick Links
STock Hub ReMovaL:
1. Set control knob to "FREE" or 4x2 position.
2. Remove cover mounting bolts and pull cover off.
3. Remove the bolt and washer from end of the axle shaft, if
applicable. Some models use a snap ring at end of axle shaft,
remove snap ring. Remove hub body mounting nuts and re-
move hub body. To dislodge and remove locking cones, place a
socket slightly larger than cones over cones against hub flange,
rap sharply with a hammer.
Bearing
Washer
Hub Nut
1,050(76,103)
Hub & Disc
dRive FLange ReMovaL:
NOTE - 1989 - Newer models equipped with "Automatic Differential Disconnect" are
not equipped with locking hubs. Drive flange must be removed to allow locking hub
installation.
5. If applicable, use a hammer and chisel (or straight slot screw driver) to knock off
flange cap. Remove bolt and washer from end of axle shaft.
6. Remove six flange mounting nuts. Follow procedure described in step #3 for
locking cone removal.
7. Install and tighten two 8mm bolts into threaded holes in flange. Tighten evenly until flange brakes are loose and can be removed.
SeRvice inSTRucTionS:
Hubs should be serviced at same time as wheel bearings. Clean and coat with oil. The hubs should never be packed with grease. We
recommend checking wheel bearing adjustment and locknut torque to be sure they are within vehicle manufacturer's specifications.
Engage hubs one mile monthly.
2121 bLounT Road PoMPano beacH, FL 33069 www.MiLeMaRkeR.coM 1-800-886-8647 © coPyRigHT MiLe MaRkeR inc
Lock Washer
Adjusting Nut
Lock Nut Gasket Cone Washer
Bolt
Free Wheeling Hub
MANuAl Hubs
ToyoTa Locking Hub
ModeL 11041-02 / 11039-02 / 11010-02 / 490 / 466
4. Automatic Hubs Only: After removing hub body from axle
hub, use a screw driver or needle nose pliers to remove
snap ring from the automatic hub. (See illustration) Using
a torx screw driver, remove screws that hold break drum
to the adjusting nut. Using a large spindle nut socket (hub
wrench) remove adjusting nut. This will complete the
automatic hub removal.
Brake Drum
Adjusting Nut
Gasket
Thrust Washer
Hub Body
Cone Washer
Brake Shoe
Thrust Plate
Snap Ring
Snap Ring
Inner Cam
Snap Ring
Snap Ring
Snap Ring Gasket
Washer
Ring
AuTOMATic Hubs
Washer
35 (360,26)
Cone Washer
Gasket
Flange
Outer Cam
Cover
Snap Ring Cap
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Mile Marker RECOVERYGEAR+ 11041-02
Summary of Contents for Mile Marker RECOVERYGEAR+ 11041-02
- Page 1 Hubs should be serviced at same time as wheel bearings. Clean and coat with oil. The hubs should never be packed with grease. We recommend checking wheel bearing adjustment and locknut torque to be sure they are within vehicle manufacturer’s specifications. Engage hubs one mile monthly. 2121 bLounT Road PoMPano beacH, FL 33069 www.MiLeMaRkeR.coM 1-800-886-8647 © coPyRigHT MiLe MaRkeR inc...
- Page 2 Marker will, as its option, repair or replace the product or necessary replacement parts at no charge to you, provided you remove the product from the vehicle and return it prepaid to Mile Marker Inc. if the product was purchased in the united states, the owner must contact our warranty department to get a Return Goods Authorization (RGA) Number before returning the product.
Need help?
Do you have a question about the RECOVERYGEAR+ 11041-02 and is the answer not in the manual?
Questions and answers