Summary of Contents for Satisure B14WET01-1T1-US-W
- Page 1 Wireless Doorbell User Manual Please read this user manual before using and installation.
- Page 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - -...
- Page 3 Introduction Thank you for purchasing our product! Our new wireless doorbell use advanced technology to make sure detection signals more accurate. We dedicates to improve your living quality and simplify your lifestyle as development direction, We have been committed to researching and developing more high quality and competitive products.
- Page 4 Overview 1.Plug-in Receiver The receiver has an LED Indicator on the front, 3 buttons on the side, Up Button, Down Button and Volume Button. (2 buttons: Volume Button and Music Button). The AC plug and Speaker are on the back. AC Plug AC Plug Volume control...
-
Page 5: How Does It Work
How Does It Work Receiver Ding Built-in transmitter Dong transmitter Antenna doorbell- transformer Switch cabinet Doorbell-button Fuse shasten... -
Page 6: Technical Specification
Technical Specification Receiver working voltage AC100V-240V Sound pressure level < 110dB Receiver AC power consumption < 0.25 W (standby mode) Working frequency 433.92 MHz Operating temperature -20 °C-60 °C Wireless range 100-200M (in open area) transmitter working voltage 3-24V AC/DC... -
Page 7: Powering The Transmitter
Operating Instructions 1.POWERING THE INDOOR CHIME RECEIVE Plug the receiver into the outlet. The receiver will perform better if kept away from other electrical equipment (eg: TV, microwave.) 2.POWERING THE TRANSMITTER Connect the transmitter wire to the positive and negative terminals of the doorbell 3.SOUND VOLUME CONTROL Press the volume control button on the receiver to cycle through 5 volume levels, including MUTE mode. -
Page 8: Setting Ringtone
(2) Long press the Volume button for 5 seconds until a Ding-dong is heard and the LED indicator starts flashing toenter into pairing mode. (3)Press the transmitter button to send a signal to receiver.when the pairing ( ringtone sync ) is successful, the receiver will play the selected ringtone automatically. - Page 9 Volume Button Volume control Up Button Music button Down Button 6.RESET Press Down Button (or Music Button) for 5 seconds to reset receivers to default. When receiver sounds 'Ding Dong' with LED flashing that means the reset was successful. Then you can follow the STEP 4 to pair again.
-
Page 10: Transmitter Installation
Transmitter Installation Connect the power cord Circuit Boards transmitter Circuit Boards (+/-) power cord(+/-) Control lights Antenna... -
Page 11: Warranty And After-Sale Service
Problem Cause Solution Check if the Check if the transmitter transmitter is board LED is on broken？ The receiver does not Pair the transmitter Unsuccessful pairing respond to the and receiver again transmitter The receiver Push the Volume Button Mute mode is ON only lights to make a sound but NO sound... - Page 12 Chimes List 01 Ding-dong,Ding-dong 30 Electric piano 30 Electric piano 02 Ding-dong,Ding-dong 31 Starry night 31 Starry night 03 Ding-dong,Ding-dong 32 Marimba 32 Marimba 04 Ding-dong,Ding-dong 33 Alerting Ringtone 33 Alerting Ringtone 05 Corsica Doorbell 34 Electric Ringtone 34 Electric Ringtone 06 Ding-dong 35 Alerting Ringtone 35 Alerting Ringtone...
- Page 13 印刷要求： 1, 材质 : 128g 铜版纸， 双面印刷 2, 装订方式 : 风琴折 3, 印刷方式: 黑白印刷 4, 尺寸 : 80X80mm 5, 特殊要求 : /等比放大 8X8 产品型号 签 名 日 期 WET01 英语 版 本 设 计 曾发 2023.09.05 比 例 版本 更改记录 更改标识...
Need help?
Do you have a question about the B14WET01-1T1-US-W and is the answer not in the manual?
Questions and answers