Mr. Beams MB570 Installation Instructions

Installation Instructions
Path Light
MB570
Thank you
for purchasing the Mr Beams
Path Light. We are committed to eliminating
darkness using the latest in Light-Emitting Diodes
(LEDs). LEDs are the most efficient and durable
light sources available. We are certain that your
light will contribute to a safer environment and
provide light where you need it at a very
reasonable cost.
What is included per light:
• 2 Motion Sensor Path Lights
• 4 Screws & 4 Anchors
• 2 Stakes & 2 Brackets
What you need to install:
• 1 Small Screwdriver
• 3 C-Cell Alkaline Batteries
(per light)
Path Light Features:
Motion/Light Sensor: The Path Light instantly turns on
when it detects motion from up to 15 feet away. The light
sensor conserves battery life by preventing the light from
activating in daylight.
Auto Shut-off: Path Light shuts off automatically after 20
or 60 seconds (optional) if no motion is detected.
Bright LED: 35 Lumens covers up to 140 sq ft.
Durable, Weather Resistant: Tight seals and UV resistant
material allow the light to work in all weather conditions.
Glow Mode Option: Emits soft glow when darkness is
sensed for safety.
NOTE: Light sensor only allows light to activate in darkness. We recommend you test in a dark room or closet.
Mounting with Stake
2. Set auto shut-off to 20 sec or 60 sec.
Setting to 20 seconds will extend battery life.
3. Set "GLOW" to on if you want it to glow in
1. Remove rear cover of
darkness or off for no glow. Setting to off will
Path Light by removing 2
screws on back. extend battery life.
Mounting on Wall
1. Determine location for mounting light. Flip
rear cover upside down and use holes for thumb
screws as template to mark two holes for anchors
and/or screws (included). We recommend
mounting the screws parallel to the ground if
mounting on a vertical surface. Make sure that
screws are precise distance from each other as
defined by the distance of the thumb screw holes.
Replace rear cover and thumb screws.
Battery Caution:
1) Do not mix old and new batteries
2) Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium)
or (Nickel Metal Hydride) batteries
3) Do not dispose of batteries in fire
4)Batteries should be recycled or disposed of as per state and local guidelines
www.mrbeams.com
Tips:
®
•
Use only new alkaline C-Cell batteries with 1.5V rating.
•
Do not mix old and new batteries. If batteries are not new, it may cause the light to malfunction.
•
Install batteries with polarity in correct position.
•
Light may activate when batteries are inserted. Simply take light into a dark room. Allow
batteries to settle, then test activation.
If your light will not turn off, it means that it is time to replace the batteries.
•
LED Light
Stake
4. Insert 3 C-Cell batteries
into light. Replace cover.
Bracket
6. Insert Path Light into
5. Insert stake into ground
by twisting it and pushing mounting bracket.
it down or digging a hole.
7. Insert mounting
bracket into stake.
2. If using anchors, use 3/16" drill bit to drill
holes and insert anchors. Drive screws into an-
chors so that screw head potrudes 1/8" from the
surface. If using only screws, us 1/8" drill bit to
drill holes and insert screws so that screw head
protrudes 1/8" from the surface.
3. Slide light down so screws are securely held
by track.
* Visit our website to view installation video.
* 1 year limited warranty. Visit site for details.
600 Beta Drive, Unit 100, Mayfield Village, OH 44143
Motion & Light
Sensor
877.298.9082