Online LED Store LAMPHUS Cruizer Dual-Stacked Series Manual

www.online-led-store.com
US Toll Free: 1-855-LED-ONLINE (533-6654)
International: 1-909-212-0993
Fax: (909) 575-6722
E-mail: support@online-led-store.com
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE.
• Proper installation of this product requires the installer to have a good understanding of
automotive electronics, systems, and procedures.
• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle
components or other vital parts could be damaged by the drilling process. Check both sides of
the mounting surface before drilling begins. Also de-burr any holes and remove any metal
shards or remnants. Install grommets into all wire passage holes.
• If this manual states that this product may be mounted with suction cups, magnets, tape or
Velcro®, clean the mounting surface and dry thoroughly prior to apply adhesive for maximum
adhesion.
• Do not attempt to activate or control this device in a hazardous driving situation.
Mounting
CAUTION! Permanent mounting of this product will require drilling. It is
absolutely necessary to make sure that no other vehicle components could
be damaged by this process. Check both sides of the mounting surface
before starting. If damage is likely, select a different mounting location.
1. Select a desired mounting location. Make sure there is at least 6.5" of clearance in order
for the light to fit properly over the mounting location.
2. Place the Swivel Bracket over the desired mounting surface.
3. Mark the area where the mounting hole(s) is to be drilled. Confirm that no vehicle parts
could be damaged by the drilling process.
4. Using a drill bit of appropriate size, drill a mounting hole for the Mounting Bolt. Thoroughly
de-burr all hole(s).
5. Secure the Swivel Bracket onto the mounting surface using the included fasteners.
6. Affix the mounting base(s) on the light bar to the swivel bracket using the included
fasteners.
7. Adjust the light unit to the desired tilt angle prior to tightening the fasteners all the way.
8. Refer to Mounting Diagram for additional details.
Wiring
WARNING! All customer supplied wires that connect to the positive
terminal of the battery must be sized to supply at least 125% of the
maximum operating current and FUSED at the battery to carry that load. DO
NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
RED – To 10-30 VDC Power Source, for Bottom Row SPOT Lights
BLUE – To 10-30 VDC Power Source, for Top Row FLOOD Lights
BLACK – To Chassis Ground
Specifications by Model
Input Voltage: 12 – 30 VDC
Model Amperage @ 12 VDC
CRLB201 2.2
CRLB202 5.4
CRLB203
CRLB204 7.8
CRLB205 8.2
CRLB206 9.3
Output Wattage
36
72
7 108
144
180
216
Online LED Store © 2012-2018 All Rights Reserved
LAMPHUS Cruizer
®
LED Flood/Spot Off-Road Light Bar
(CRLB201, CRLB202, CRLB203, CRLB204, CRLB205, CRLB206)
SKU: ORZLEDLBR204, 207, 210, 212, 215, 218
• Do not install this product or route any wires in the deployment area of your air bag. Equipment
mounted or located in the air bag deployment area will damage or reduce the effectiveness of
the air bag, or become a projectile that could cause serious personal injury or death. Refer to
your vehicle owner's manual for the air bag deployment area. The User/Installer assumes full
responsibility to determine proper mounting location, based on providing ultimate safety to all
passengers inside the vehicle.
• This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a
combination of these lights. Do not stare directly into these lights. Momentary blindness and/or
eye damage could result.
Mounting Diagram
Dual-Stacked Series
™