Universal Remote Control UR5U-8820L Operating Instructions

Introduction
1
Operating Instructions For
CLIKR TM -5
The UR5U-8820 is designed to
CLIKR ™ -5
operate the Motorola, Scientific-Atlanta,
Pioneer, Pace Micro and Samsung digital
set tops, plus the majority of TV, VCR, DVD
Cable Remote Control
and AUDIO equipment on the market as
shown below.
CABLE : Cable Converters
UR5U-8820L
VCR : VCRs and TV/VCRs
AUX : Audio Receivers and DVRs, etc.
2 Replacing Batteries
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
Operations
3
DEFAULT STATE:
Component Default: CABLE
Channel Default: CABLE channel and
numbers through the CABLE. You have the
option of controlling your CABLE channel and
numbers through the TV or VCR. Refer to
section F for programming steps.
Volume Default: CABLE volume and mute
through the CABLE. You have the option of
Universal Remote Control, Inc.
controlling your CABLE volume and mute
through the TV, VCR or DVD. Refer to section
www.universalremote.com
G for programming steps.
OCE-0052D REV 02 (04/30/07)
Button Functions
4
TV : Televisions
DVD: DVD Players
5 Programming the Remote Control
There are two ways you can program your CLIKR TM -5 remote:
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Auto-Search Method scans through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, a component LED will light for
30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit setup
mode and you will need to start over.
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV, VCR, STEP5 Save the code. (Same as for 3-Digit Code
DVD or AUX) to be programmed and Programming Method - Section A).
[OK/SEL] button simultaneously for 3
Now, repeat the Auto-Search Method for those
seconds. The Component LED light will
Components you could not program earlier with the
turn on for 30 seconds indicating the unit
Pre-Programmed Method.
is ready to be programmed.
STEP3 Point the remote control toward the
C. Finding a Component Button's
Component and enter the 3-digit code
number assigned to your brand.
Setup Code Number
*Note : If the 3-digit code number you just entered
If you used the Auto-Search Method to program a
is correct, the Component will turn Off. If
Component, you may not know what the correct code
it did not turn Off, continue entering code
number is. Here is a way for you to identify the code
numbers listed for that brand until the
number, so you can record it for future reference.
Component turns Off.
STEP1 Press the [COMPONENT] button (TV, VCR, DVD
STEP4 After you've entered the correct code
or AUX) you want to verify and the [OK/SEL]
number and the Component has turned
button simultaneously for 3 seconds. The
Off, press the [POWER] button to turn the
Component LED light will turn on for 30 seconds.
Component back On. Now it's time to test
STEP2 Press the [INFO] button and count the number
the VOLUME and MUTE buttons for the
of times the Component LED light blinks. This
TV (or PLAY and STOP buttons for VCR
number indicates the first digit of the code,
and DVD) to make sure they all work. If
followed by the second and third, each
any of the functions do not work as they
separated by a one second pause when the
should, repeat from STEP 3 using the next
LED will turn off.
3-digit code number listed for that brand.
*Note : 10 blinks represents the number zero.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the same
Example : One blink, (pause), eight blinks, ( pause)
[COMPONENT] button one more time.
and three blinks, indicates code number 183.
The Component LED light will blink twice
D. AUX Function: Programming a 5
to confirm that the code was successfully
stored.
Component
Now, program the rest of your Components by
You can take advantage of the AUX function to program
repeating STEPS 1-5.
a 5 th Component such as a second TV, VCR, DVD or
Audio Component.
*Note : If the Pre-Programmed Method did not
work, or if the Code Tables do not list STEP1 Turn on the 5 th Component you want to
program (TV, VCR, DVD or Audio).
your Component brand, use the Auto-
Search Method as explained in Section B.
STEP2 Press the [AUX] button and the [OK/SEL] button
simultaneously for 3 seconds.The [AUX]
Component LED will turn on for 30 seconds.
B. Auto-Search Method
STEP3 Press the [COMPONENT] button you want to
STEP1 Turn on the Component you want to
setup. Point the remote control toward the
program (TV, VCR, DVD or AUX).
Component and enter the 3-digit code number
STEP2 Press the [COMPONENT] button (TV, VCR,
assigned to your brand.
DVD or AUX) to be programmed and
*Note : If the 3-digit code number you just entered is
[OK/SEL] button simultaneously for 3
the correct number, the Component will turn
seconds. The Component LED light will
Off. If it did not turn Off, continue entering
turn on for 30 seconds indicating the unit
code numbers listed for that brand until the
is ready to be programmed.
Component turns Off
STEP3 Point the remote toward the Component
STEP4 Test functions. (Same as for 3-Digit Code
and press the [CH ] or [CH ] button one
Programming Method - Section A). If any of
step at a time or keep it pressed. The
the functions do not work as they should, you
remote will emit a series of ON/OFF
need to find a new code.
commands. Release the [CH ] or [CH ]
button as soon as the Component turns Off.
STEP5 Once you have found the correct 3-digit code,
STEP4 Test functions. (Same as for 3-Digit Code save it by pressing the [AUX] button one more
Programming Method - Section A). If any time. The Component LED light will blink twice
of the functions do not work as they
to confirm the code was stored. Now when
should, repeat from STEP 3 using [CH ] or
you press the AUX button, all the buttons will
[CH ] buttons to find the correct code.
work with that 5 th Component.
E. Programming the System On/Off Button STEP2 Press the [VOL +] button.
STEP3 Press the [TV] button.
This allows you to program the System On/Off button so
The Component LED will blink twice to
it can send up to five power On/Off commands with one
confirm the programming.
button press.
To return to original state:
STEP1 Press the [CBL] button.
If you wish to restore the CBL volume control in CBL mode,
STEP2 Press the [SYSTEM ON/OFF] button and the
repeat the above steps but press [CBL] in STEP3 .
[OK/SEL] button simultaneously for 3 seconds.
The [CBL] button will turn on for 30 seconds.
H. Programming a 'Macro' button
STEP3 Press the first [COMPONENT] button you want
to store in the [SYSTEM ON/OFF] button and
In CABLE mode, the M button can be programmed to
then the [POWER] button. Repeat this for
act as a 'Macro' . This allows you to program from
other Components until you have stored all the
one up to three separate channels that can be
desired power commands into the [SYSTEM
accessed by simply pressing the programmed
ON/OFF] button.
Macro button.
STEP4 Press the [CH+] button to save the power
STEP1 Press the [CBL] button to select the CBL
commands you stored. The [CBL] button will
mode.
blink twice to confirm the commands have
STEP2 Press the [M] button and [OK/SEL] button
been saved.
simultaneously for 3 seconds. The [CBL]
button will turn on for 30 seconds.
F. Programming Channel Control
STEP3 Enter the 3 or 4-digit code for the channel
You can program the channel controls (Channel Up,
you want programmed first (for example,
Channel Down, Last and Numbers) from one Component
007) using the Number Pad, then press the
to operate in another Component mode. Default channel
[STOP] button. Then enter the code for the
control settings on the remote control are as follows:
next channel (for example, 050), then press
the [STOP] button. Repeat this process for
CBL : CBL T V : CBL VCR : CBL
the third channel. The [CBL] button will blink
DVD : DVD AUX : AUX
th
once for each channel entered.
If you wish to store the TV channel control in TV mode,
STEP4 Press the [CH+] button to store the channels
use the following steps.
that were selected. The [CBL] button will
STEP1 Press the [TV] button and the [OK/SEL] button
blink twice to confirm the storage of
simultaneously for 3 seconds. The [TV]
commands.
Component LED will turn on for 30 seconds.
To access the programmed channels, press the [M]
STEP2 Press the [VOL -] button.
button once. This will bring up the first channel. Press
STEP3 Press the [TV] button again.
once again and it will bring up the second channel.
The Component LED will blink twice to confirm
Press again and it will bring up the third channel.
the programming.
To return to original state:
I. Low Battery Warning
If you wish to restore the CABLE channel
When the batteries are low and need to be replaced
control in TV mode, repeat the above steps but
with fresh batteries, the Component LED lights will
press [CBL] in STEP3 .
blink 2 times in sequence whenever a [POWER]
button is pressed to turn on equipment.
G. Programming Volume Control
You can program the volume controls (Volume Up,
J. Memory Lock System
Volume Down and Mute) from one Component to
This remote control is designed to retain programmed
operate in another Component mode. Default volume
memory for 10 years even after batteries are removed
control settings on the remote control are as follows:
from the remote control.
CBL : CBL T V : TV VCR : TV
DVD : TV AUX : AUX
K. Record Your Component Set-up Codes
If you wish to store the TV volume control in CBL
TV Set-up Code Number:
mode, use the following steps.
VCR Set-up Code Number:
STEP1 Press the [CBL] button and the [OK/SEL]
button simultaneously for 3 seconds. The
DVD Set-up Code Number:
[CBL] Component LED will turn on for 30
AUX Set-up Code Number:
seconds.