Anker Soundsync Manual

Welcome

With this Soundsync, you can:

• Enable your non-Bluetooth speakers to play music from your Bluetooth-enabled devices such as smartphones or tablets.
• Enable your non-Bluetooth devices such as a traditional MP3 player, TV or PC to transmit audio wirelessly to your Bluetooth speaker.

At a Glance

1. 3.5mm AUX input/output port
2. SPDIF Transmitter port (input from TV)
3. SPDIF Receiver port (output to speaker)
4. Micro USB charging port
5. Power/Multi-function button
6. Battery/Status indicator
7. TX (transmitter) / RX (receiver) switch

Charging

• Use the provided or certified cable to prevent any damage.
• Fully charge your Soundsync before the first use.
• Disconnect your Soundsync from the charger when fully charged. Do not charge for extended periods.

	Flashing red	Low battery
	Steady red	Being charged
	Off	Fully charged

Connecting

SPDIF mode
SPDIF (Sony/Philips Digital Interface) is a type of digital audio interconnect used in consumer audio equipment to output audio over reasonably short distances. The signal is transmitted over a coaxial cable with RCA connectors or an optical cable with TOSLINK connectors.

AUX mode

• Although SPDIF mode is the default mode, Soundsync will automatically switch to AUX mode when a 3.5mm audio cable is plugged in.
  

Powering On/Off

	Press and hold for 2 seconds	Powered on		Flashing blue
		Powered off		Flashing red

Transmit Mode (TX)

To enter Transmit mode, turn the TX/RX switch to the TX position.
Connect Soundsync to a non-Bluetooth multimedia device (such as TV, PC) via a 3.5mm audio cable or an optical cable. The audio source from the device can be transmitted to a Bluetooth headphone or speaker via Soundsync.

	Press twice	Enter/Exit Bluetooth pairing mode
	Rapidly flashing blue
	Slowly flashing blue	Connected to one device (TX mode)
	Steady green	Connected to two devices

Connect to two Bluetooth headphones/speakers at a time

• This function is only available in TX mode.
• You can play music on two headphones/speakers at a time.

1. Pair your Soundsync with the first Bluetooth headphone/speaker via Bluetooth. Once successfully connected, turn off both your Soundsync and the first Bleutooth headphone/speaker.
2. Turn on the Bluetooth on your second headphone/speaker. Press and hold the multi-function button for 2 seconds or press twice to enter Bluetooth pairing mode.
3. Place your Soundsync next to the second headphone/speaker and wait for 30 seconds for connection. Once successfully connected, turn off your Soundsync.
4. Turn your first headphone/speaker on, then turn on your Soundsync and wait for another 30 seconds. Both headphones/speakers will have sound if successfully connected.

• If the connection fails, reboot your Soundsync or repeat the steps above.
  

Receive Mode (RX)

To enter Receive mode, turn the TX/RX switch to the RX position.
Connect your Soundsync to a non-Bluetooth headphone, speaker, or car stereo etc. Via a 3.5mm audio cable. Then pair your Soundsync with a Bluetooth-enabled smartphone or tablet via Bluetooth. The music from your Bluetooth-enabled device then can be transmitted to the nonBluetooth headphone, speaker or car stereo etc.

RX Mode

	Press twice
	Flashing red and blue alternately	Enter/Exit Bluetooth pairing mode (Receiver mode)
	Steady blue	Connected to one device (RX mode)
	Steady green	Connected to two devices

Connect to two smartphones/tablets at a time

• This function is only available in RX mode.
• Soundsync can only receive audio source from one smartphone/tablet at a time.

1. Connect the first smartphone/tablet to your Soundsync, turn off Bluetooth on your first smartphone/tablet once connected.
2. Press the multi-function button twice to enter Bluetooth pairing mode. Pair the second smartphone or tablet with your Soundsync.
3. When the second smartphone/tablet is successfully connected to Soundsync, turn on the Bluetooth on your first smartphone/tablet again, and find "Anker Soundsync" on the Bluetooth list to connect.

RX Mode

Press

Play/Pause (Only available in RX mode)

Specifications

Specifications are subject to change without notice.

DC input	5V 1.5A
Battery type	350mAH Rechargeable Lithium Battery
Charging time	2 hours
AUX play time (Receiver mode)	Approximately 17 hours
AUX play time (Transmitter mode)	Approximately 25 hours
SPDIF play time (Receiver mode)	Approximately 13 hours
SPDIF play time (Transmitter mode)	Approximately 20 hours
Operation frequency	2.402-2.480 GHz
Operating temperature range	14 to 131°F / -10 to 55 。C
Bluetooth version	V5.0
Bluetooth range	10 m / 33 ft
Bluetooth protocol	RX: A2DP AVRCP; TX: A2DP