Table of Contents
Advertisement
CTGRD3N 3110 manual booklet.QXD
INSTALLING BATTERIES
1. On the remote control's back, push the tab and lift off the battery
cover.
2. Obtain two (2) new AAA alkaline batteries. Match the + and –
marks on the batteries to the + and – marks in the battery case,
then insert the new batteries.
3. Press the battery cover back into place. The tab should click when
the cover is locked.
4. Test the unit by pressing
POWER
batteries are inserted correctly, the LED will blink once.
NOTE: When batteries need replacement, the remote control will stop operat-
ing. Remove the old batteries and insert new ones within 30 minutes to ensure
all of your programming information is restored.
SETTING UP YOUR COMPONENTS
The One For All 3 Devices remote control is preprogrammed at the fac-
tory to operate an RCA TV and VCR, a Motorola (GI) cable box, and a
Toshiba DVD player. To control devices other than the default brands,
perform the following steps; otherwise skip this section:
NOTE: For TV/VCR Combo control, see the next section.
1. Turn on a device (e.g.,VCR) and, if applicable, insert media, (e.g.,
cassette or disc).
NOTE: Please read steps 2-4 completely before proceeding. Highlight or write
down the codes and device you wish to program before moving on to step 2.
2.
On the remote control, press a device key once (i.e.,
, or
). Press and hold
CBL/SAT
TV
then release
.
SET
3. Use the Manufacturer's Codes (starting on page 11) to locate the
type of device and brand name and then enter the first four-digit
code for your component. If performed correctly, the LED will blink
twice.
5/2/06
3:08 PM
Page 5
and any mode key (e.g.,
). If the
TV
,
VCR/DVD
until the LED blinks twice,
SET
5
NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try
entering the same code again.
4.
Aim the remote control at the device and press
The device should turn off. If it does not respond, repeat
steps 2-3, trying each code for your brand until you find one
that works. If it still does not work, try Searching For Your
Code .
NOTE: If the device does not have a POWER key, press the (PLAY) key.
5. Repeat steps 1 through 4 for each device you want to control.
PROGRAMMING TV/VCR COMBO CONTROL
Perform the following instructions to control a TV/VCR Combo:
1. Turn on the TV/VCR Combo and insert a video cassette.
NOTE: Please read steps 2-4 completely before proceeding. Highlight or write
down the codes and device you wish to program before moving on to step 2.
2.
On the remote control, press
the LED blinks twice, then release
3. Use the Setup Codes For TV/VCR Combos (on page 12) to locate the
brand name and then enter the first four-digit code for your device.
If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try
entering the same code again.
4.
Aim the remote control at the device and press
It should turn off. If the device does not respond, repeat
steps 2-3, trying each code for your brand until you find one
that works. If it still does not work, try Searching For Your
Code .
NOTE: If the device does not have a POWER key, press the (PLAY) key.
PROGRAMMING TV/DVD COMBO CONTROL
Perform the following instructions to control a TV/DVD Combo:
1. Turn on your TV/DVD and insert a disc.
2.
On the remote control, press
until LED blinks twice, then release
3.
Use the Setup Codes For TV/DVD Combos (on
page 12) to locate the brand name and then enter the first four-
digit code for your device. If performed correctly, the LED will blink
twice.
4.
Aim the remote control at your TV/DVD and press
Your TV/DVD should turn off. If your original TV/DVD
remote control did not have a POWER key, press
TV/DVD should start to play. If your TV/DVD does not
respond, repeat steps 2-4, trying each code listed for your
brand until you find the one that operates your TV/DVD.
5. Your One For All 3 Devices is now programmed to operate your
TV/DVD.Write your TV/DVD code for future reference.
Remember, if you want to use your One For All 3 Devices to operate
your TV/DVD, press the VCR/DVD key first.
6
once.
POWER
. Press and hold
until
VCR/DVD
SET
.
SET
once.
POWER
. Press and hold
VCR/DVD
SET
.
SET
.
POWER
.Your
PLAY
Hide quick links:
Advertisement
Table of Contents
