Universal Electronics CONTOUR Manual

Contour battery. It can leak chemicals that can
destroy electronic parts.
WARNING: Dispose of old batteries
promptly and properly. Do not burn or
bury them.
To Install Batteries:
1. Open the battery compartment
cover (located on the back of
the remote).
2. Place the AA batteries in the
compartment and match the + and -
polarity symbols inside.
3. Replace the cover.
NOTE: When the battery voltage is low, the
TV or STB key blinks 5 times after a
keypress.
STEP 2: PROGRAM FOR TV
CONTROL
The Contour remote control is pre-
programmed to control your set-top box
but it must be manually programmed in
order to control the TV power and volume.
Follow the instructions below to program
your remote for your TV.
1. Turn on the TV.
2. Press the TV key on the remote.
3. Press and hold SETUP until the TV key
blinks twice, then release.
4. Enter the first five-digit code for the
TV brand that you wish to program.
The LED blinks once as each digit is
entered. If the code is valid, the LED
blinks twice.
NOTE: If the LED does not blink twice,
repeat steps 2 to 4 and try entering the
code again.
5. Aim the remote at the TV and press
MUTE. The TV volume should mute.
If it does not, repeat steps 3–5, trying
each code for your brand until you
find one that works. If you cannot
find a code that works, see
"Searching for Your Code".
User's Guide
SEARCHING FOR YOUR CODE
By UNIVERSAL ELECTRONICS
If your TV does not respond to the remote
after trying all codes listed for your brand,
GETTING STARTED
or if your brand is not listed, try searching
for your code:
The Contour remote control is intended to
1. Turn the TV on.
be simple to set-up and to use. Just follow
the two steps below and the remote will be
2. Press the TV key once.
ready for use in just a few short minutes.
3. Press and hold SETUP until the TV key
blinks twice, then release.
STEP 1: INSTALL BATTERIES
4. Enter 9 9 9 1. The LED blinks twice.
5. Aim the remote at the TV and press
Your Contour remote control requires 2
MUTE. The remote sends IR codes
AA batteries (included).
from its library to the TV, starting
Battery Use And Safety with the most popular code first. If
• Use only fresh batteries of the the TV responds, go to step 7.
required size and recommended type. 6. If the TV does not respond, press
• Do not mix old and new batteries, CH+ and the remote will test the next
different types of batteries (standard, TV code. Continue to press Channel
alkaline, or rechargeable), or Up until the TV turns off.
rechargeable batteries of different
Note: Press CH- to try the previous code.
capacities.
7. Now that you have found the correct
• If you do not plan to use the remote code, press SETUP to save the code
for an extended period, remove the for your TV.
CHANGING VOLUME LOCK To clear the macro, repeat steps 1-5 above,
but do not enter a series of commands at
The Contour remote control comes preset
step 4.
with volume controls (Volume Up, Volume
TROUBLESHOOTING
Down, and MUTE) all locked to your TV.
This section describes how to disable and
PROBLEM: TV or STB key does not blink
enable volume lock.
when you press a key.
Locking Volume Control
SOLUTION: Try pressing different keys.
1. Press and hold SETUP until
Replace the batteries with 2 new AA
either the TV or STB key blinks
batteries.
twice.
PROBLEM: LED blinks when you press a
key, but device does not respond.
2. Enter 9 9 3, the LED blinks twice.
3. Press the mode key for the device you SOLUTION: Make sure the remote is aimed
want to control (for example, TV). at your device and is not more than 40 feet
4. The LED blinks twice. Now when you away.
press VOL+, VOL-, or MUTE, the
PROBLEM: LED blinks one long blink
selected device (for example, TV)
while in SETUP mode.
controls the volume regardless of the
SOLUTION: An entry error has occurred
current mode.
(for example, wrong key). Try entering the
sequence again.
Unlocking All Volume Control
PROBLEM: Remote does not control
1. Press and hold SETUP until
devices or commands are not working
either the TV or STB key blinks
properly.
twice, then release.
SOLUTION: Try all listed codes for the
Enter 9 9 3, the LED blinks twice.
2.
device. Make sure the device operates with
3. Press VOL+. The LED blinks four
an infrared remote control.
times. Volume is independently
PROBLEM: No volume on a device.
controlled for all programmed
SOLUTION: See "Changing Volume Lock"
devices.
and make sure the volume is not locked to
a different mode already.
PROGRAMMING MACROS
A QUICK LOOK AT THE CONTROLS
Your Contour remote control includes the
ability to program the A, B, C, and D keys
Press this key...
with a Macro function. Each one can be
set up to perform a pre-programmed set Select a device (either TV
of sequential key presses with the press of
or STB).
one key. A macro can be used to control a
Turn the selected device on
home theater operation, to set a favorite
channel, or for other multiple functions
or off.
you would like to control with one key
Program sequences.
press. Moreover, each Macro Key can hold
up to 15 key presses total.
You can program a macro that operates
Select the next or previous
regardless of what mode you are in, or one
channel.
that only operates when you are in a
specific mode.
NOTE: Programming a new macro over an
Raise or lower the sound
existing one erases the original macro.
level.
Programming a Macro
Press MUTE to turn the
1. Press and hold SETUP until
sound off or on.
either the TV or STB key blinks
twice, then release.
Move the cursor in the
2. Press 9 9 5. The TV or STB key blinks menu screens.
twice.
Press OK to choose the
3. Press the key you wish to assign a
highlighted menu option.
macro on.
4. Enter the series of commands you
Rewind, fast forward,
want the macro to execute (up to 15
pause, or play to control an
commands).
ON DEMAND movie or
5. Press and hold SETUP until either the
recorded show.
TV or STB key blinks twice, then
release.
View the current channel
Now, when you press the preset macro key,
and program information.
the remote sends the series of commands
you have entered, regardless of what mode
Display the menu for the
you are in. For example, you could
selected device.
program a macro key to turn on both your
TV and cable box and select a particular
channel.
Press this key... To...
Exit the selected device's
menu, guide, or program
without making a menu
selection.
Display the program guide
for the selected device.
Switch the TV's input to
view TV or video
programs.
Directly enter channels
(for example, 09 or 31).
Press Enter to send
channel number entries on
some TV models.
Use the A, B, C, and D keys
for programming macros.
(See "Programming
Macros".)
MANUFACTURER'S CODES
Setup Codes for TVs
A-Mark 10047, 10054, 10165
Accuscan 10047, 10018, 10135
Action 10030, 10185
Admiral 10047, 10054, 10017, 10051,
10093, 10463, 10180, 10018,
10165
To...
Advantz 10282
Advent 10761, 10783, 10815, 10817,
10842, 11933
Adventuri 10000
Agna 10150
Aiko 10092
Akai 10060, 10812, 10702, 10030,
10145, 10151, 10672, 11903,
11935
Albatron 10700, 10843
Alfide 10672
Alleron 10030
Ambassador 10150, 10177
America Action 10180
American High 10000, 10060
Ampro 10751
Amstrad 10171, 10177
Amtron 10000, 10180
Anam 10180
Anam National 10055
AOC 10180, 10030, 10185
Apex Digital 10156, 10748, 10879, 10765,
10185, 10767, 11943
Audinac 10180
Audiovox 10451, 10180, 10092, 10623,
10802, 10875, 11937, 11951,
11952
Aventura 10171
Axion 11937
Baysonic 10180
Beaumark 10017, 10178, 10030
Belcor 10030
Bell & Howell 10054, 10154, 10093
BenQ 11032
Boxlight 10893
Bradford 10180
Brockwood 10178, 10030 GE
Broksonic 10236, 10463, 10180, 10177,
11929, 11935, 11938
Candle 10030
Capehart 10017, 10178, 10030, 10092
Gemini
Carnivale 10030
Gibralter
Carver 10054
Go Video
Celebrity 10000
Go Vision
Celera 10765
GoldStar
Changhong 10156, 10765, 10767, 10783
Cineral 10451, 10092 Gradiente
Citek 10047
Grundig
Citizen 10054, 10000, 10451, 10463, Grundy
10180, 10060, 10030, 10171,
Grunpy
10092, 10282, 11928
Haier
Civet 10185
Hallmark
Clairtone 10185
Clarion 10180
Harley Davidson
Classic 10030, 10092
Colortyme 10047, 10054, 10017, 10060, Harman/Kardon
10178, 10030, 10018
Harvard
Commercial Solutions 11447, 10047
Havermy
Conic 10178
Heathkit
Contec 10180, 10185
Helios
Craig 10180, 10171, 10282
Hello Kitty
Crosley 10054, 10000, 10180, 10030,
Hewlett Packard
10171, 10187
Hisense
Crown 10093, 10180, 10672
Hitachi
Crown Mustang 10672
Curtis Mathes 10047, 10054, 10154, 10000,
10051, 10451, 10093, 10180,
10060, 10702, 10178, 10030,
HP
10145, 10166, 10018, 10466,
Hyundai
11147, 11347, 11919
Ima
CXC 10180
Infinity
Cytron 11326
Insignia
Daewoo 10451, 10178, 10092, 11661,
10623, 10661, 10672, 11755, Inteq
11756, 11928
JBL
Dayton 10092
JCB
Daytron 10178, 10030, 10092
Jensen
Dell 11080, 11178
JIL
Denon 10145, 10055, 10511
Jutan
Denstar 10628
JVC
Digital Life 10872
Dumont 10017, 10180, 10178 Kamp
Durabrand 10463, 10180, 10178, 10171, Kawasho
11034
KEC
Dwin 10093, 10720, 10774
Kenwood
Eaton 10060
KLH
Electroband 10000, 10185
Kloss
Electrograph 11755
Konka
Electrohome 10154, 10000, 10150, 10178,
10030, 10151, 10185
Kost
Emerald 10178, 10177
KTV
Emerson 10047, 10154, 10451, 10236,
Lark
10463, 10180, 10150, 10178,
LG
10171, 11944, 11929, 11928,
10623, 10282, 10185, 10177,
10135
Lloyd's
Envision 10030, 10813
Logik
Epson 10833, 10840
LXI
ESA 10812, 10171, 11944
Fisher 10054, 10154, 10000, 10159
Fortress 10093
Fujitsu 10683, 10809, 10853
Magnasonic
Funai 10000, 10180, 10171, 11904
Futuretech 10180
Magnavox
Gateway 11755, 11756
11447, 10047, 10000, 10051,
10451, 10060, 10178, 10030,
10135, 10055, 10282, 11147,
11347, 10018, 11917, 11919,
11922
10047
10017, 10000, 10030
10886
11937
10047, 10054, 10178, 10030,
10018, 11154, 11926
10053
10706, 10672, 10683
10180
10180
11034, 10768
10236, 10180, 10178, 10135,
10187
10000, 10180, 10060, 10178,
10030, 11904
10054
10180
10093
10017
10865
10451
11089, 11494, 11502
10748
10047, 10054, 10017, 10000,
10051, 10178, 11145, 10145,
10018, 10055, 10151, 10185,
11904, 11960
11089, 11494, 11502
10849, 10865
10236, 10180, 10178
10054
10171, 11326, 11517
10017, 10145
10054
10000
10761, 10815, 10817, 11933
10030
10030
10054, 10053, 10030, 10055,
10731, 11253
10017, 10180, 10185
10030, 10185
10180, 10060
10180, 10030
10156, 10180, 10765, 10767
10030
10180, 10080, 10628, 10632,
10638, 10703, 10707, 10720
11262
10463, 10180, 10030, 10185
10154
10054, 11265, 10060, 10178,
10030, 10700, 10856, 11154,
11178, 11758
10236, 10180, 10030, 11904
10236, 10180
10047, 10054, 10017, 10154,
10000, 10156, 10051, 10093,
10060, 10053, 10178, 10030,
10171, 10166, 10055, 10135,
10018, 10159, 10165
10054, 10000, 10156, 10093,
10030, 10092, 11928
10047, 11454, 10054, 10154,
10000, 10250, 10051, 10180,
10060, 10030, 10171, 10092,
10706, 10187, 10282, 10386,
10802, 11254, 11755, 11904,
11931, 11944