Download Print this page

NARDA PMM PA6002 User Manual

Wideband rf power amplifier

Advertisement

Quick Links

Manufacturing Plant:
NARDA
Via Benessea, 29/B
Safety
17035 - Cisano sul Neva (SV)
Test
Tel.: +39 0182 58641
Solutions
Fax: +39 0182 586400
S.r.l. Socio Unico
User's Manual
PMM PA6002
WIDEBAND RF POWER
9 kHz - 230 MHz / 10 Watts
SERIAL NUMBER OF THE INSTRUMENT
You can find the Series Number on the rear panel of the instrument.
Series Number is in the form: 0000X00000.
The first four digits and the letter are the Series Number prefix, the last five digits
are the Series Number suffix. The prefix is the same for identical instruments, it
changes only when a configuration change is made to the instrument.
The suffix is different for each instrument.
Document PA6002EN-40504 – Copyright © NARDA 2024
www.narda-sts.it
nardait.support@narda-sts.it
narda-sts@onlinepec.it
AMPLIFIER

Advertisement

loading
Need help?

Need help?

Do you have a question about the PMM PA6002 and is the answer not in the manual?

Questions and answers

Summary of Contents for NARDA PMM PA6002

  • Page 1 The first four digits and the letter are the Series Number prefix, the last five digits are the Series Number suffix. The prefix is the same for identical instruments, it changes only when a configuration change is made to the instrument. The suffix is different for each instrument. Document PA6002EN-40504 – Copyright © NARDA 2024...
  • Page 2 NOTE: ® Names and Logo are registered trademarks of Narda Safety Test Solutions GmbH – Trade names are trademarks of the owners. If the instrument is used in any other way than as described in this User’s Manual, it may become unsafe.
  • Page 3 Contents Page General safety considerations and instructions..EC Declaration of Conformity …………………………... Page 1 General information 1.1 Documentation........…....… 1.2 Introduction ………………........…. 1.3 Instrument items......…....…… 1.4 Optional accessories..…...………………...…. 1.5 Main specifications......…....….. 1.6 Typical Performances…………………………………. 1.7 Front panel.....……………..…..…..…… 1.8 Rear panel…………......…..…..…… 2 Installation Page 2.1 Introduction........…....…...
  • Page 4 Figures Figure Page Front Panel........…..…... Rear Panel........…... Tables Table Page Technical Specifications....…... Contents...
  • Page 5 • To prevent the possible danger of electrocution, do not remove any covers, panels or guards installed on the device, and refer only to NARDA Service Centers if maintenance should be necessary; • To maintain adequate protection from fire hazards, replace fuses only with others of the same type and rating;...
  • Page 6 Descrizione AMPLIFICATORE DI POTENZA Description POWER AMPLIFIER Modello PMM PA6002 Model è conforme ai requisiti essenziali delle seguenti Direttive: conforms with the essential requirements of the following Directives: Bassa Tensione 2014/35/EU Low Voltage Compatibiltà...
  • Page 7 • an accessories check list to verify all accessories enclosed in the packaging. PMM PA6002 is a wideband RF power amplifier covering a 9 kHz ÷ 230 MHz 1.2 Introduction frequency range with output power level of 10 Watts into a 50 Ohm load.
  • Page 8 Table 1-1 lists the PMM PA6002 performance specifications. 1.5 Main specifications The following conditions apply to the specification: • The PMM PA6002 needs at least 5 minutes warm-up before operate; TABLE 1-1 Technical specifications 9 kHz ÷ 230 MHz Frequency Range:...
  • Page 9 1.6 Typical Performances Typical Gain at Nominal Power [dB] [dB] 0.001 0.01 1000 [MHz] Typical Gain at Nominal Power/2 [dB] [dB] 0.001 0.01 1000 [MHz] General Information...
  • Page 10 Power output at 1dBc [W] 20.0 18.0 16.0 14.0 12.0 10.0 0.001 0.01 1000 [MHz] Compression at Nominal Power [dBc] [dB] 0.001 0.01 1000 [MHz] General Information...
  • Page 11 2nd Harmonic at Pn [dBc] 3rd Harmonic at Pn [dBc] [dBc] 0.001 0.01 1000 [MHz] General Information...
  • Page 12 1.7 Front panel Legend: 1 - Input BNC Connector 2 - Output N Connector 3 - Power Meter 4 - Power On Light 5 - Alarm Light Fig 1-1: Front Panel 1.8 Rear panel Legend: 1 - Mains power switch 2 - Fuse receptacle 3 - Mains power connector 4 - Equipment serial number...
  • Page 13 2 - Installation This section provides the information needed to install your PMM PA6002. 2.1 Introduction Included is information pertinent to initial inspection, power requirements, line voltage and fuse selection, power cables, interconnection, environment, instrument mounting, cleaning, storage and shipment.
  • Page 14 To clean the equipment do not use any solvent, thinner, turpentine, acid, acetone or similar matter to avoid damage to external enclosure. 2.12 Hardware PMM PA6002 is delivered ready to use. Remove the amplifier from his cardboard box and connect power cable to rear panel mains plug. Push the Installation main switch to "ON"...
  • Page 15 3. Ensure the vent grid be free to allow a correct Amplifier ventilation. PMM PA6002 operates from 85 to 264 VAC thanks to its internal switching 3.3 Connection to Power power supply. The AC Voltage input selection is thus not required. The unit Source is connected to the AC power outlet with line cord supplied.
  • Page 16 This page intentionally left blank Operating Instruction...
  • Page 17 Moreover, we are continuously improving our quality, but we know this is a never ending process. We would be glad if our present efforts are pleasing you. Should one of your pieces of NARDA equipment need servicing you can help us serve you more effectively filling out this card and enclosing it with the product.
  • Page 18 Suggerimenti / Commenti / Note: Suggestions / Comments / Note:...