Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ASTRO IA-542-A
- Page 1 Interface Conversion Adaptor(LVDS to DVI) IA-542-A Instruction Manual Ver.1.0...
- Page 3 Interface Conversion Adaptor (LVDS to DVI) IA-542-A Instruction Manual 2006.2 Ver.1.0 ASTRODESIGN,Inc...
-
Page 5: Table Of Contents
Contents Contents................................i Before Use................................. ii Introduction ............................... ii Safety precautions ............................. ii How this manual is configured......................... iii Packing details..............................iv Chapter 1 Concerning the IA-542-A.......................1 1.1. Outline..............................1 1.2. Features ..............................1 1.3. Parts and their functions...........................2 1.3.1. IA-542-A front panel ........................2 1.3.2. -
Page 6: Before Use
Thank you for very much purchasing the model IA-542-A LVDS to DVI conversion adapter. This manual contains details on the operation procedures to be followed when the IA-542-A is used, the checkpoints and precautions to be observed, and so on. -
Page 7: How This Manual Is Configured
Before Use How this manual is configured This manual contains the operating instructions for the IA-542-A. Information on the operating methods, precautions and other aspects are presented in the following sections. Please read through this manual to ensure that you will operate the adapter correctly. -
Page 8: Packing Details
Standard items IA-542-A IA-542-A instruction manual (what you are reading): 1 copy Optional items AC adapter, S-8453 (made by Kaga component Corp.) The IA-542 –A is designed to run using a DDC power supply. If a DDC power supply cannot be used, the IA-542 –A can also be run on the power supplied from this AC adapter. -
Page 9: Chapter 1 Concerning The Ia-542-A
Concerning the IA-542-A 1.1. Outline The IA-542 (LVDS to DVI conversion adapter) converts LVDS inputs into DVI-D signals and outputs them. 1.2. Features Dot clock frequency in wide band Table 1-2-1 shows the frequency specifications of the input and output dot clocks. -
Page 10: Parts And Their Functions
Chapter 2 1.3. Parts and their functions 1.3.1. IA-542-A front panel ⑦ ① ② ③ ④ ⑤ ⑥ Fig.1-3-1 Front panel 1. DVI digital serial connector 2. Clock mode selector switch: For switching the clock mode 1/1 to 1/2 or vice versa 3. -
Page 11: Ia-542-A Rear Panel
1 Concerning the IA-542-A 1.3.2. IA-542-A rear panel Fig. 1-3-2 Rear panel 1 LVDS input connector (CH1) 2 LVDS input connector (CH2) -
Page 13: Chapter 2 Appendix
Chapter 3 Appendix 2.1. Connector pin layouts 2.1.1. LVDS input connectors • Connector: Made by 3M (10226-1210-VE) • Input: LVDS Fig. 2-1-1 Pin layout Table 2-1-1 Pin numbers Pin no Input signal Pin no Input signal RD＋ DDC_GND AGND（RD） RD− DDC_AVCC（+5V）... -
Page 14: Dvi Digital Serial Input Onnector
2.1.2. DVI digital serial input connector • Connector: DVI-I (74320-1004) made by Molex • Output: TMDS Fig. 2-1-1 Pin layout Table 2-1-1 Pin numbers Pin no. Signal Pin no. Signal TMDS DATA2- SENSE TMDS DATA2+ TMDS DATA0- TMDS DATA2/4 G TMDS DATA0+ TMDS DATA0 G DDC CLK... -
Page 15: Device Input Pin Support
2 Appendix 2.2. Device input pin support 2.2.1. LVDS receiver device pin support • The table below shows the correspondence between the data output pins of the LVDS receiver and the RGB data. • LVDS receiver: THC63LVD104A [THINE] Table 2-2-1 LVDS device pin support table DATA［DISM］... - Page 16 2.2.2. DVI transmitter device pin support • The table below shows the correspondence between the data input pins of the DVI transmitter and the RGB data. • DVI transmitter: SiI160CT100 [Silicon Image] Table 2-2-2 DVI device pin support table EVEN CH ODD CH DVI Transmitter’s Pin DVI Transmitter’s Pin...
-
Page 17: Ia-542-A Specifications
2 Appendix 2.3. IA-542 –A specifications 2.3.1. Specifications LVDS（×2CH） Input DVI （×1CH） Output Input［MHz］ Output［MHz］ Clock mode 25 〜 90 （×1CH） 25 〜 90 Frequency 1 / 1 20 〜 82.5（×2CH） 40 〜 165 1 / 2 DISM LVDS Input Open LDI 2.3.2. -
Page 18: Concerning The Ddc Power Supply
• Although the DDC power supply incorporates an overcurrent protection device, it should not be used at current levels exceeding the rating. • Under no circumstances must power be supplied from the connected device to the DDC CAUTION power supply. If power is connected, the IA-542-A and connected device may malfunction. -
Page 19: Outline Drawing
2 Appendix 2.3.4. Outline drawings ... - Page 20 IA-542-A NOTICE An incorrectly collated manual or a manual with missing pages will be ● replaced. All copyrights pertaining to this product are the property of ASTRODESIGN. ● This manual may not be copied in whole or in part without written ● ...
Need help?
Do you have a question about the IA-542-A and is the answer not in the manual?
Questions and answers