Related Manuals for AIRMATIC KODI KLIP KTA-3 Series
Summary of Contents for AIRMATIC KODI KLIP KTA-3 Series
- Page 1 R e b a r C o n n e c t i o n Sy s t e m s KTA-3, 4, 5, 6 Series REBAR CONNECTOR TOOL OWNER OPERATOR MANUAL PN: 10-00085 AIRMATIC airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 2 CAUTION This symbol indicates a general statement to assist the user in the operation or maintenance of the equipment. IMPORTANT AIRMATIC 2 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
-
Page 3: Table Of Contents
NOTE: The Model and Serial Number of your Tool is located on the Tool's Housing. These numbers and the Date of Purchase (DOP) should be recorded: Model: ________________ SN: _________________ DOP: _____________ AIRMATIC 3 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... -
Page 4: Tool Specification
Klip. Both the safety unit and the Trigger must be released to allow the feeder to advance the Klip rack, and then activated again to fire a second Klip. Klips cannot be bump fired. AIRMATIC 4 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... -
Page 5: General Safety Instructions
Tool and the air supply, should limit the Tool's inlet pressure to a maximum of 110 PSI (7.6 Bar). Do not exceed 110 PSI (7.6 Bar) inlet air pressure. Excessive air pressure will damage the Tool and void the warranty. CAUTION AIRMATIC 5 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... -
Page 6: Service And Repair
3. Use only KODI genuine OEM parts. Contact your Area Distributor to order parts. AIRMATIC 6 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... -
Page 7: Tool Operation
Compressed air is an invisible hazard. Any Tool, hose or other component through which it passes is capable of releasing an explosive force which could result in personal injury or death. AIRMATIC 7 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... - Page 8 3. Adjust the directional Exhaust Deflector so that exhaust air is directed away from the Operator. The Exhaust Deflector can be rotated in either direction to one of its eight (8) stop positions. See Figure #4 Below Figure #4: Adjusting the Exhaust Deflector AIRMATIC 8 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 9 CONNECTION: Klip Magazine must be perpendicular to the primary rebar and the adjoining rebar must be pushed into the other rebar slot. See Figure #6 Below Figure #6: Parallel Connecting Rebar AIRMATIC 9 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
-
Page 10: General Maintenance
Tool. Certain solvents will damage the Tool's rubber and plastic components. 3. Always make sure that all screws are kept tight. Loose or missing screws can cause damage to expensive Tools parts which could cause injury. AIRMATIC 10 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... -
Page 11: Removing Klips From Tool
Klip Rack to ensure Sensor Shaft Engagement. IMPORTANT Figure #9: Opening Door Figure #8: Releasing Lock Figure #8: Releasing Lock Figure #10: Removing Klips Figure #11: Engaging Lock Mechanism AIRMATIC 11 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... -
Page 12: Compressed Air System
In cold weather conditions where airline moisture can freeze, do not force the Tool to cycle by increasing air pressure. Air pressure over 110 PSI (7.6 Bar) will damage the internal parts and void the warranty. AIRMATIC 12 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... -
Page 13: Appendix A: Troubleshooting
4. The rebar flexed-away during firing. 4. Not enough Back Pressure on the rebar. 5. The Tool bounced off Joint. 5. Constant physical pressure must be applied to the Tool during shooting. AIRMATIC 13 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... - Page 14 Spring [#441] or Push Spring [#437]. Replace damaged parts. – OR – (c) Sensor Shaft [#441] on Door not fully dis-engaged. Check that Safety Unit is functioning. Replace Safety Unit or Sensor Shaft as required. AIRMATIC 14 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 15 – OR – (b) Apply more downward pressure on Tool before pulling Trigger. If you have any problems that cannot be easily overcome, call our National Service Center, AIRMATIC, at 1-215-333-5600 before continuing use. AIRMATIC 15 of 24 airmatic.com | 215.333.5600...
-
Page 16: Appendix B: Parts Breakdown
R e b a r C o n n e c t i o n Sy s t e m s APPENDIX B: PARTS BREAKDOWN AIRMATIC 16 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com... - Page 17 FEEDER ASSEMBLY 70-10308 CUSHION REBUILD KIT - includes O-RING & 71-20015 70-10401 O - RING PACKING 70-10402 INLET TUBE 70-10403 O - RING 70-10404 O - RING 70-13405 BASE 76-A6813 BOLT AIRMATIC 17 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 18 R e b a r C o n n e c t i o n Sy s t e m s AIRMATIC 18 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 19 (* * **) O-RING & PACKING 70-10307 AIR PLUG 70-10308 CUSHION 70-10401 O - RING 70-10402 INLET TUBE 70-10403 O - RING 70-10404 O - RING 76-A6813 BOLT 70-10407 SAFETY GUIDE AIRMATIC 19 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 20 R e b a r C o n n e c t i o n Sy s t e m s AIRMATIC 20 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 21 (* * **) O-RING & PACKING 70-10307 AIR PLUG 70-10308 CUSHION 70-10401 O - RING 70-10402 INLET TUBE 70-10403 O - RING 70-10404 O - RING 76-A6813 BOLT 70-10407 SAFETY GUIDE AIRMATIC 21 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 22 R e b a r C o n n e c t i o n Sy s t e m s AIRMATIC 22 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 23 (* * **) O-RING & PACKING 70-10308 CUSHION 70-10401 O - RING 70-10402 INLET TUBE 70-10403 O - RING 70-10404 O - RING 76-A6813 BOLT 70-10407 SAFETY GUIDE 70-46408 SAFETY ACTUATOR AIRMATIC 23 of 24 airmatic.com | 215.333.5600 | infocenter@airmatic.com...
- Page 24 R e b a r C o n n e c t i o n Sy s t e m s PN: 10-00085 052423 AIRMATIC airmatic.com | 215.333.5600 | infocenter@airmatic.com...
Need help?
Do you have a question about the KODI KLIP KTA-3 Series and is the answer not in the manual?
Questions and answers