Summary of Contents for holzkraft NTS 201
- Page 1 Translated from German to English - www.onlinedoctranslator.com Operating instructions Wet/dry grinder NTS 201 NTS 256 NTS 256 NTS 201...
-
Page 2: Table Of Contents
Product identification 1.1 Copyright................3 1.2 Customer Service............3 Wet/dry grinder 1.3 Limitation of Liability............3 2 Security ............3 NTS 201 5750201 2.1 Explanation of symbols............3 NTS 256 5750256 2.2 Operator's Responsibility ........4 2.3 Safety data sheets............4 2.4 Qualifications of personnel .......... -
Page 3: Introduction
We are always interested in information and introduction experiences that arise from use and can be valuable for improving our products. By purchasing the HOLZKRAFT wet/dry sander you have made a good choice. 1.3 Limitation of liability Please read the operating instructions carefully All information and instructions in this manual have before commissioning. -
Page 4: Operator's Responsibility
Security Operator’s obligations: If the machine is used in a commercial setting, the operator is subject to legal obligations regarding DANGER! occupational safety. Therefore, the safety instructions in this manual, as well as the safety, accident prevention, This combination of symbol and signal word and environmental protection regulations applicable to indicates an immediately dangerous situation which, the machine's area of use, must be observed. -
Page 5: Qualifications Of Personnel
Security 2.4 Qualifications of staff Manufacturer: Certain work may only be performed by the The various tasks described in this manual place manufacturer's qualified personnel. Other personnel are different demands on the qualifications of the persons not authorized to perform this work. Please contact our entrusted with these tasks. -
Page 6: General Safety Instructions
Intended Use 3 Intended use 2.6 General safety instructions - The grinder may only be operated and maintained The wet/dry sander is designed exclusively for sanding by persons who have read and understood these wood or wood-like materials and is universally operating instructions. -
Page 7: Residual Risks
Technical data Technical data 3.2 Residual risks Even if all safety regulations are observed and the Model NTS 201 NTS 256 machine is used correctly, there are still residual risks, which are listed below. Dimensions 480 x 340 x 375... -
Page 8: Environmental Conditions
Transport, packaging, storage 5 Transport, packaging, storage 4.1 Environmental conditions 5.1 Delivery and transport 1 °C to 40 °C Working temperature humidity max. 90% delivery max. 1000 m Operating height Upon delivery, inspect the wet/dry grinder for visible transport damage. If any damage is found, report it dry, non-flammable Working environment immediately to the shipping company or dealer. -
Page 9: Machine Description
Machine description 6 Machine description 6.2 Scope of delivery NTS 201 and NTS 256 6.1 Representation - Water collection container Illustrations in this operating manual may differ - Stripping paste from the original. - Angle gauge NTS 201 - Universal grinding device... -
Page 10: Install Mounting Bracket
Operation - Model NTS 256: In the direction of rotation. Use the bidirectional switch With this model, there are two options for to change the direction of rotation of the grinding positioning the water collection container. wheels. Remove the workpiece from the machine before For new grinding stones, select the lower mounting changing the direction of rotation. - Page 11 Depending on the switch's position, the grinding wheel can rotate forward or backward. (Definition: Forward = clockwise, Reverse = counterclockwise) Model NTS 201: Grinding JIP The fixture supplied with the grinder can be used as a universal attachment for a variety of tools and can be positioned to grind with and against the rotation of the grinding wheel.
- Page 12 Operation Angle guide Water collection container The wet grinding stone is designed for wet grinding The sharpener comes with an angle guide to help only and should never be used for dry grinding determine and maintain the cutting angle for a variety without water.
-
Page 13: Installation Location
Operation Sharpen Ensure sufficient freedom of movement for work, adjustment, and maintenance. There must be at least 1 Many tools can be sharpened with the leather honing m of clearance on each side from the wall to the grinder. wheel and the included honing paste. 7.3 Electrical connection A NOTICE! Check the electrical connection, cables and contacts... -
Page 14: Care, Maintenance And Repair/Repair
Care, maintenance and repair 8 Care, maintenance and repair 8.2 Maintenance and repair Check the general condition of the device before each use: DANGER! - Check switches and safety devices for wear or damage - Before starting any cleaning or maintenance work, switch off the machine and unplug it. -
Page 15: Troubleshooting
Troubleshooting 9 Troubleshooting Possible causes Elimination Mistake The wet/dry grinder does The on/off switch is defective. Have the grinder checked by an not start. electrician and replace any damaged parts. The wet/dry sander slows The user presses the workpiece too hard Reduce the contact pressure. -
Page 16: Disposal, Recycling Of Old Devices
Recycling of materials helps to reduce the consumption of raw materials. For - Device type:Grinding machine NTS 201 more information about recycling of this product, - Item number:5750201 please contact your local council, your household waste... -
Page 17: Spare Parts Drawings
The following drawing is intended to help you identify the necessary spare parts in the event of a service call. If necessary, send a copy of the parts drawing with the marked components to your authorized dealer. Spare parts drawing NTS 201 Fig. 2: Spare parts drawing NTS 201 NTS Series | Version 1.01... - Page 18 Spare parts Spare parts list NTS 201 Pos. Pos. Designation Crowd Designation Crowd Grinding device Power switch cable clamp Universal support Star grip screw Power cable Cable feedthrough sleeve Locking button Stripping paste adjusting nut Angle guide Phillips screw M4x12...
- Page 19 Spare parts Spare parts drawing NTS 256 Fig. 3: Spare parts drawing NTS 201 NTS Series | Version 1.01...
- Page 20 Spare parts Spare parts list NTS 256 Pos. Pos. Designation Crowd Designation Crowd Base unit Washer D10 Ball bearing 6200-2RS bearing housing Phillips screw M5x35 bearing block Wave spring washer D35 Hexagon nut M5 Main shaft Hexagon nut M4 Ball bearing 6003-2RZ tension spring V-belt pulley Belt cover plate...
-
Page 21: Electrical Circuit Diagrams
Electrical circuit diagrams 12 electrical circuit diagrams Electrical diagram NTS 201 Fig. 4: Circuit diagram NTS 201 NTS Series | Version 1.01... - Page 22 Electrical circuit diagrams Electrical diagram NTS 256 Fig. 5: Circuit diagram NTS 256 NTS Series | Version 1.01...
-
Page 23: Eu Declaration Of Conformity
According to Machinery Directive 2006/42/EC Annex II 1.A Manufacturer/distributor: Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt hereby declares that the following product Product group: Holzkraft® woodworking machines Name of the machine: NTS 201 Item number: 5750201 NTS 256 5750256 Machine type:... - Page 24 www.holzkraft.de...
Need help?
Do you have a question about the NTS 201 and is the answer not in the manual?
Questions and answers