Summary of Contents for Lumber Jack PDE1500
- Page 1 SAFETY AND OPERATING MANUAL 1HP Professional Dust Collector PDE1500 ORIGINAL INSTRUCTION...
-
Page 2: Technical Specification
TECHNICAL SPECIFICATION Attention: Please choose proper power source, voltage and frequencies that are shown in the label for your product. Dust Collector PDE1500 Motor Power 1500W Max. Air Suction Capacity 2500 m ³/h Max. Static Pressure 2600 Pa Inlet Port Diameter... - Page 3 17. NEVER STAND ON THE MANCHINE. Serious injury could occur if the machine is tipped or if the cutting tool is unintentionally contacted. 18. CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function: check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.
-
Page 4: Electrical Requirements
ELECTRICAL REQUIREMENTS POWER SUPPLY AND MOTOR SPECIFICATIONS WARNING: To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection. Use a separate electrical circuit for your tools. To avoid shock or fire, if power cord is worn cut, or damaged in any way, have it replaced immediately. -
Page 5: Accessories And Attachments
ACCESSORIES AND ATTACHMENTS RECOMMENDED ACCESSORIES WARNING: To avoid injury: • Use only accessories recommended for the machine. • Follow instructions that accompany accessories. Use of improper accessories may cause hazards. • Use only accessories designed for this machine to avoid injury from thrown broken parts or workpieces. •... - Page 6 A. Separation housing B. Dust collection bag (plastic) C. Hose clamp D. Dust export E. Rubber gasket F. Motor, impeller and base assembly G. Bag and filter clamp H. Y adapter with cover I. Support leg J. Caster K. Hose L.
- Page 7 2. Attach three support legs to the base by using M8X16 hex head bolts and 8mm flat washers. Support legs M8X16 hex head bolts and 8mm washers 3. Install the separation housing to the three support legs with M8X16 hex head bolts and 8mm flat washers. M8X16 hex head bolts and 8mm washers Separation housing...
- Page 8 4. Attach the cleaning handle onto the shaft of canister filter, tighten hex head bolt. Install the canister filter assembly and dust bag to the upper and lower port of separation housing with the clamp. Cleaning handle Filter clamp Canister filter Bag clamp Dust collection bag 5.
- Page 9 6. Attach the hose between the separation housing and the impeller housing with two clamps. Tighten the clamps to secure the hose. Hose clamp Hose Hose clamp 7. Install the Y adapter over the impeller intake hole, then secure it in place with the M5X10 pan head screw.
-
Page 10: Operation
OPERATION Once the assembly is complete, test run your dust collector to make sure it runs properly and is ready for regular operation. Connect the machine to power. Verify that the machine is operating correctly by turning the switch ON. When running normally, the machine runs smoothly without abnormal vibration or impact noise. -
Page 11: Maintenance
MAINTENANCE Warning: Turn off the machine and disconnect from the power supply before conducting maintenance work or settings. Cleaning the Canister Filter Clean the canister filter and dust collection bag frequently to keep the collector's performance at its optimum. To clean the canister filter: 1. -
Page 12: Troubleshoothing
TROUBLESHOOTHING PROBLEM CAUSE SOLUTION Machine does not ⚫ Defective motor, power cable or ⚫ Specialized personnel should check the work plug. machine. ⚫ Overload protector is tripped. ⚫ Reset the overload protector. ⚫ Start capacitor is at fault. ⚫ Test/replace. ⚫... -
Page 13: Assembly Diagram
ASSEMBLY DIAGRAM... -
Page 14: Part List
PART LIST Description QTY. Description QTY. Hex head bolt M8X25 Inlet cover Y adapter Motor Hex nut M5 Hex head bolt M6X10 Connection chain Base Pan head screw M5X10 Caster Flat washer 6mm Pan head screw M5X10 Impeller cover Hex nut M6 Pan head screw M5X10 Support leg Left thread hex head bolt M6X25... - Page 15 Unit C, Manders Ind. Est., Old Heat h Road, Wolverhampton, WV1 2RP. Declare that the product: Designation: Professional Dust Collector Model: PDE1500 Complies with the following Directives: Standards & technical specifications referred to: EC Council Directive 2006/42/EC Machinery Report No.4840324272800...
Need help?
Do you have a question about the PDE1500 and is the answer not in the manual?
Questions and answers