Fujitsu enterprise server getting started guide (4 pages)
Summary of Contents for Fujitsu Oracle Sun SPARC Enterprise M8000
Page 1
Sun SPARC Enterprise M8000/M9000 Servers Installation Guide Part No. 819-4200-15 July 2010, Revision A...
Page 2
INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. Unless otherwise expressly set forth in such agreement, to the extent allowed by applicable law, in no event shall Oracle or Fujitsu Limited, and/or any of their affiliates have any liability to any third party under any legal theory for any loss of revenues or profits, loss of use or data, or business interruptions, or for...
Page 3
Aucune partie de ce produit, de ces technologies ou de ce document ne peut être reproduite sous quelque forme que ce soit, par quelque moyen que ce soit, sans l’autorisation écrite préalable d’Oracle et/ou ses sociétés affiliées et de Fujitsu Limited, et de leurs éventuels bailleurs de licence.
Contents Using This Documentation ix Installation Workflow 1–1 Preparing to Install the System 2–1 Safety Precautions 2–1 Before Installing the Server 2–2 2.2.1 Checking Environmental Requirements 2–2 2.2.2 Facility Power Requirements 2–4 2.2.2.1 Power Supply Connection Specifications 2–4 2.2.2.2 Power Supply Requirements 2–6 2.2.2.3 Grounding 2–11 2.2.3...
Page 6
3.3.2 Connecting the Power Cabinet 3–10 3.3.2.1 Connecting the Base Cabinet and Power Cabinet 3–10 3.3.2.2 Connecting the M9000 Server Expansion Cabinet and the Power Cabinet 3–20 Connecting Cables 3–24 3.4.1 Connecting the power cords 3–24 3.4.1.1 Single-Phase Power Feed 3–25 3.4.1.2 Three Phase Power Feed 3–31 3.4.2...
Page 7
3.7.6 Powering Off the System 3–60 Connecting Additional Peripheral Devices 3–60 Connecting Your Domains to the Network and Running the SunVTS Software 4–1 Network Connection Outline 4–1 Connecting the System to Each Network 4–4 Verifying a Network Connection 4–6 Starting the Solaris Operating System 4–6 Verifying the Operation Using the SunVTS Software 4–8 4.5.1 Installing the SunVTS Software 4–8...
Page 8
B.2.5 Using the fmadm faulty Command B–11 B.2.5.1 Using the fmadm config Command B–11 B.2.6 Using the fmstat Command B–12 Traditional Solaris Troubleshooting Commands B–12 B.3.1 iostat Command B–12 B.3.1.1 iostat Command Options B–13 B.3.2 prtdiag Command B–13 B.3.2.1 prtdiag Command Options B–14 B.3.3 prtconf Command B–16 B.3.3.1...
Using This Documentation This installation guide describes how to install and set up Oracle’s Sun SPARC Enterprise M8000/M9000 high-end servers.This document is written for technicians and authorized service providers (ASPs). This document assumes that the system has already been unpacked and mounted in an equipment cabinet. References herein to the SPARC Enterprise M8000 server or M8000 are references to the Sun SPARC Enterprise M8000 server.
Using UNIX Commands This document might not contain information about basic UNIX commands and procedures such as shutting down the system, booting the system, and configuring devices. Refer to the following for this information: Software documentation that you received with your system ■...
Page 11
Application Title Format Location Getting started Sun SPARC Enterprise M8000/M9000 Servers Getting Started Hard Shipping Guide Copy Online Planning/Installation Sun SPARC Enterprise Equipment Rack Mounting Guide (Sun Online Rack 1000, 900 and Sun Rack II) Installation Sun SPARC Enterprise M8000/M9000 Servers Installation Guide Hard Shipping Copy...
Documentation, Support, and Training Function Documentation http://docs.sun.com/ Support http://www.sun.com/support/ Training http://www.sun.com/training/ Documentation Feedback Submit comments about this document by clicking the Feedback[+] link at http://docs.sun.com. Include the title and part number of your document with your feedback: Sun SPARC Enterprise M8000/M9000 Servers Installation Guide, part number 819-4200-15 SPARC Enterprise M8000/M9000 Servers Installation Guide •...
C H A P T E R Installation Workflow This chapter describes the work required in the workflow from the server installation to hardware operation verification. For details, see TABLE 1-1 Installation Workflow TABLE 1-1 Installation Stage Workflow Task Preliminary checks Before installing the server, check the environmental requirements.
Page 14
Installation Workflow (Continued) TABLE 1-1 Installation Stage Workflow Task ↓ Connect the Ethernet port of the XSCF unit to the system control network. Verify that you can log into the XSCF Shell through the LAN. See Section 3.7.3, “Connecting an Ethernet Port”...
C H A P T E R Preparing to Install the System This chapter describes preparations for installation. Section 2.1, “Safety Precautions” on page 2-1 ■ Section 2.2, “Before Installing the Server” on page 2-2 ■ Section 2.3, “Requirements for Server Installation” on page 2-13 ■...
When disconnecting a LAN cable, you may not be able to reach the connector lock ■ with your fingers. If that is the case, press the connector lock with a flathead screwdriver to disconnect the cable. You could damage the PCI card if you force your fingers into the gap rather than use a flathead screwdriver.
Page 17
Ambient Environmental Requirements TABLE 2-1 Operating Range Non-Operating Range Optimum Ambient 5˚C to 32˚C Unpacked: 21˚C to 23˚C temperature (41˚F to 89.6˚F) (70˚F to 74˚F) 0˚C to 50˚C (32˚F to 122˚F) Packed: -20˚C to 60˚C (-4˚F to 140˚F) Relative 20% RH to 80% RH to 93% RH 45% RH to 50% RH humidity...
lists recommended temperatures and humidities for computer rooms. TABLE 2-2 Recommended Temperatures and Humidities for Computer Rooms TABLE 2-2 Near the Underfloor Air Outlet Detection and Regulation Point Conditioning Setup Temperature Humidity Temperature Humidity Remarks Direct — — — 24±2˚C 75±4˚F 45±5% —...
Page 19
Power Supply Connection Specifications TABLE 2-3 Power ‡ Name Destination cord Length Plug Type Number of Plugs Outlet in Facility M8000 Japan 3.0 m (9.8 ft) 30 A-250 V 3P, 3 (single-power feed) 30 A-250 V 3P, locking Server locking type plug type (NEMA L6-30R) 6 (dual-power feed) (NEMA L6-30P)
2.2.2.2 Power Supply Requirements The following figures show the input power systems for the high-end servers: Single-phase power supply system (M8000 server) ( FIGURE 2-1 ■ Single-phase power supply system (M9000 server) ( ■ FIGURE 2-2 Three-phase delta power supply system ( ■...
Page 21
Single-Phase Power Supply System (M8000 Server) FIGURE 2-1 Dual-power feed system (Note 1) (Note 2) Power feed A Power feed B distribution board distribution board Note – (1) To connect multiple input cords of the server to the customer's distribution panel, the input cords must be independently connected to outlets on the basis of a one-to-one correspondence as shown in FIGURE 2-1 Note –...
Page 22
Single-Phase Power Supply System (M9000 Server) FIGURE 2-2 Dual-power Base cabinet Expansion Dual-power feed system cabinet feed system (Note 1) (Note 2) Power feed B Power feed A Power feed A Power feed B distribution board distribution board feed distribution distribution board board Note –...
Page 23
Three-Phase Delta Power Input Three-Phase Delta Power Input TABLE 2-5 Device Name Voltage [V] Phases Frequency M8000 + Power Cabinet 200 to 240 VAC±10% Three-phase delta 50/60 Hz +2% to -4% M9000 + Power Cabinet 200 to 240 VAC±10% Three-phase delta 50/60 Hz +2% to -4% Note –...
Page 24
Note – Connect the power feed A and the power feed B (for to a dual-power feed) separate AC power supply from each other. Three-Phase Star Power Input Three-Phase Star Power Input TABLE 2-6 Device Name Voltage [V] Phases Frequency M8000 + Power Cabinet 380 to 415 VAC±10% Three-phase star...
Three-Phase Star Power Supply System - Rear View FIGURE 2-4 M8000/M9000 Power Cabinet Input #0 Input #1 (Note) Power feed B Power feed A distribution board distribution board Note – Connect the power feed A and the power feed B (for to a dual-power feed) separate AC power supply from each other.
Grounding for Three-phase Power Supply The power cable is not supplied with the three-phase power supply M8000/M9000 servers. Ensure that the power cable wiring includes a ground wire from the distribution board to the terminal board of the power cabinet, as a part of the on-site electrical work.
Rack Space for the M8000 Server FIGURE 2-5 Empty space Rack space Rack-mountable dual-power feed Requirements for Server Installation This section lists the items and information required for installation work. Prepare these items in advance. Administration console ■ obtain any of the following from the customer ASCII terminal ■...
Page 28
Console configuration information ■ See the SPARC Enterprise M8000/M9000 Servers Site Planning Guide. No. 2 Phillips screwdriver ■ Used to remove and mount power cord covers. Flathead screwdriver ■ Used to secure cables between cabinets if the expansion cabinet of the M9000 server is mounted.
C H A P T E R Installing the Server This chapter explains how to make preparations for connecting the server to a network: Section 3.1, “Checking Components” on page 3-1 ■ Section 3.2, “Securing the Base Cabinet” on page 3-2 ■...
List of the Units That Need to be Checked TABLE 3-1 Unit Name Abbreviation Note CPU memory board unit I/O unit Crossbar unit Clock control unit CLKU eXended System Control Facility XSCFU unit FAN unit Power supply unit Hard disk drive DC-DC converter DDC_A M8000 server only...
Note – The bolts required for securing the system vary depending on the installation location. Select the appropriate bolts for the location. Note – If the server is not secured to the floor at the installation location, see Step and lower the legs so that the server does not move. 2.
Page 32
Connection Patterns FIGURE 3-1 M9000 with expansion cabinet M8000, M9000 cabinet + Power Cabinet M9000 with expansion cabinet + Power Cabinet SPARC Enterprise M8000/M9000 Servers Installation Guide • July 2010...
3.3.1 Connecting the Optional Expansion Cabinet Connect the M9000 server base cabinet and M9000 server expansion cabinet by following the procedure below. When the base cabinet and expansion cabinet are connected to each other, the side panels on the connection side of the base cabinet must be moved to the expansion cabinet.
Page 34
2. On the right side of the expansion cabinet, mount the right side panels that were removed in the previous step. Note – Unless otherwise stated, assume that you are facing the front of the expansion cabinet when you perform the work. The CD-RW/DVD-RW drive unit is equipped on the front of the expansion cabinet.
Page 35
Note – Attach the removed front cover after the operation in Section 3.4.3, “Cable Connection Between the Base and Expansion Cabinets of the M9000 Server” on page 3-34 is finished. 4. Remove the two (2) screws securing the right side cover of the base cabinet and remove the cover.
Page 36
5. Remove the two (2) screws securing the left side cover of the expansion cabinet and remove the cover. Note – Be sure to remove the cover here because it cannot be removed after the units are connected. Removing the Left Side Cover of the Expansion Cabinet FIGURE 3-5 6.
Page 37
Connecting the Base and Expansion Cabinets FIGURE 3-6 7. Secure the expansion cabinet. For details on how to secure the expansion cabinet, see Section 3.2, “Securing the Base Cabinet” on page 3-2. Lower the four leveling feet adjusting them so that the cabinet can be level. Note –...
3.3.2 Connecting the Power Cabinet Connect the server and power cabinet following the procedure below. 3.3.2.1 Connecting the Base Cabinet and Power Cabinet When the base cabinet and power cabinet are connected to each other, the side panels on the connection side of the base cabinet must be moved to the power cabinet. If the server has been shipped with the side panels already moved to the power cabinet, start the work from Step...
Page 39
2. Remove the screws securing the left side bus bar cover of the base cabinet and remove the cover. Removing the Bus Bar Cover FIGURE 3-8 M8000 M9000 Chapter 3 Installing the Server 3-11...
Page 40
3. Remove the four (4) screws securing the left side cover of the power cabinet and remove the cover. The removed cover will be remounted in Step Note – Unless otherwise stated, assume that you are facing the front of the power cabinet when you perform the work.
Page 41
Mounting Bus Bar Brackets (Temporary Tightening on the Power Cabinet FIGURE 3-10 Side) 5. Move the power cabinet so that it is on the left side of the base cabinet. 6. Remove the stabilizing attachments that are mounted on the bottom at the front and rear of the power cabinet.
Page 42
Removing a Stabilizing Attachment FIGURE 3-11 7. Connect the server and power cabinet using the six (6) bolts supplied as accessories. Mount the connecting bolts in the direction indicated by the arrows in FIGURE 3-12 Note – If the bolt holes are vertically misaligned, adjust their height by lowering the leveling feet of the power cabinet.
Page 43
Connecting the Base Cabinet and Power Cabinet FIGURE 3-12 M8000 M9000 8. Refer to Section 3.2, “Securing the Base Cabinet” on page 3-2, and secure the power cabinet. Lower the four leveling feet adjusting them so that the cabinet can be level. Note –...
Page 44
Housing the Stabilizing Attachments inside the Power Cabinet FIGURE 3-13 Step 4 10. Fully tighten the four bolts that were temporarily tightened in and secure the bus bar brackets on the power cabinet to the base cabinet. Use a torque wrench to secure the bus bar (fixed at 8.24 N·m; 84 kgf·cm). 3-16 SPARC Enterprise M8000/M9000 Servers Installation Guide •...
Page 45
Mounting the Bus Bar Brackets FIGURE 3-14 Chapter 3 Installing the Server 3-17...
Page 46
11. Connect the connectors between the base cabinet and power cabinet. Connecting the Connectors (M8000 Server) FIGURE 3-15 4 5 8 TABLE 3-1 Single-phase Three-phase None None None PSU#2 PSU#2 PSU#3 PSU#3 DPF 12V DPF 12V ACS0-CB ACS0-CB ACS1-CB ACS1-CB 3-18 SPARC Enterprise M8000/M9000 Servers Installation Guide •...
12. Attach the side cover that was removed in Step 3 to the left side of the power cabinet. 13. On the left side of the power cabinet, mount the side panels that were removed Step Mounting the Bus Bar Cover and Side Panels FIGURE 3-17 3.3.2.2 Connecting the M9000 Server Expansion Cabinet and the...
Page 49
3. Remove the left side board (1) and right side bracket (2) of the power cabinet and interchange them. Note – Unless otherwise stated, assume that you are facing the front of the power cabinet when you perform the work. There is a power supply unit (PSU) on the front of the power cabinet.
Page 50
Removing the Right Side Cover From the Power Cabinet FIGURE 3-19 5. On the bus bar of the power cabinet, attach two bus bar brackets supplied as accessories (1) with four bolts, and tighten the bolts temporarily. Note – Temporary tightening of bus bar brackets makes it easier to perform Step 6.
Page 51
Note – If the bolt holes are vertically misaligned, adjust their height by lowering the leveling feet of the power cabinet. Connecting the Expansion Cabinet and the Power Cabinet FIGURE 3-20 9. Referring to Section 3.2, “Securing the Base Cabinet” on page 3-2, secure the expansion cabinet.
10. Using the two bolts (2), mount each stabilizing attachment (1) removed in Step 7 to the inside of the power cabinet so that both attachments are housed in the cabinet (see FIGURE 3-13 They can be mounted on the rear of the power cabinet. The stabilizing attachments are stored at the top and bottom, above and below each other.
Note – If the three-phase power feed is used, connect the input power cable from the customer's distribution board directly to the power cabinet, as part of the on-site electrical work. This electrical work must be performed by the facility administrator or a qualified electrical engineer.
Page 54
2. Remove the connector cover of the AC section. Removing the Connector Cover of the AC Section: M8000 Server FIGURE 3-22 3-26 SPARC Enterprise M8000/M9000 Servers Installation Guide • July 2010...
Page 55
Removing the Connector Cover of the AC Section: Power Cabinet FIGURE 3-23 Chapter 3 Installing the Server 3-27...
Page 56
3. If the M9000 server is used, remove the connector cover and the cable tray of the AC section. Removing the AC Connector Cover and Cable Tray: M9000 Server FIGURE 3-24 3-28 SPARC Enterprise M8000/M9000 Servers Installation Guide • July 2010...
Page 57
4. Lift up the cable holder, and remove the holder. Removing the Cable Holders FIGURE 3-25 5. Connect the power cord to the AC connector on the AC section. The power cord is supplied with the server. Note – If you are installing the M9000 Server, the power cords should be connected in order, from 1 to 5, as shown in FIGURE 3-26 Chapter 3...
Page 58
Routing the power cords FIGURE 3-26 6. Mount the connector cover of the AC section. 7. If you are installing the M9000 server, mount the cable tray of the AC section while lifting the power cords. 8. Route the power cords inside the frame, and attach and lower the cable holder while holding the cord and secure it.
3.4.1.2 Three Phase Power Feed 1. Confirm that all main line switches are switched off. 2. Connect the power cables to the three-phase input section of the power cabinet. Note – If the three-phase power feed is used, connect the power input cable from the customer's distribution board directly to the power cabinet, as part of on-site electrical work.
Connecting the power cables: Three-Phase Star FIGURE 3-28 ACS for dual-power feed ACS for base power feed 3.4.2 Connecting a UPS Unit An uninterruptible power supply (UPS) unit is used to provide a stable supply of power to the system in the event of a power failure or an extensive power interruption.
Page 61
Note – UPC#0 and UPC#1 are used for dual power feed. The base cabinet has two UPS interface ports. Connect the base power feed to UPC#0 and connect the other UPSs to UPC#1. Refer to the SPARC Enterprise M8000/M9000 Servers Service Manual for the interface specifications of the UPC port.
UPC Ports FIGURE 3-30 3.4.3 Cable Connection Between the Base and Expansion Cabinets of the M9000 Server If the system includes the M9000 server expansion cabinet, connect the necessary cables between the base cabinet and expansion cabinet. The cables come with the product.
Note – The cable connection should be performed by at least two persons; one person working on the base cabinet side and the other person working on the expansion cabinet side. 3.4.3.1 Connecting Cables Between XSCF Units 1. Connect the XSCF units in the base and the expansion cabinets using a clock cable.
Page 64
Note – Please refer to Section A.2, “M9000 Server Views” on page A-4 for the location of the CLK unit. 2. Use a flathead screwdriver to secure the data cable connector. Use a torque screwdriver to secure the clock cable connector with the torque of 0.2 N·m;...
Connecting Cables Between CLKUs FIGURE 3-32 Base cabinet Expansion cabinet CLKU#0 CLKU#1 CLKU#2 CLKU#3 Data cable Clock cable 3.4.3.3 Connecting Cables Between XB Units Perform the steps below to connect the cross bar units (XB units) of the base cabinet to those of the expansion cabinet with cables.
Page 66
Cable Correspondence (For One Pair Of XB Units) TABLE 3-5 Cable type Base cabinet Expansion cabinet Expansion cabinet † Data cable XBU_B#0 -DT#0 XBU_B#8 -DT#0 Yellow † Data cable XBU_B#0 -DT#1 XBU_B#8 -DT#1 Pink † Data cable XBU_B#0 -DT#2 XBU_B#8 -DT#2 Brown †...
Page 67
Note the following points when connecting the cable: Note – When connecting the cables between the XB units, hold the cables by the connector covers and insert the connectors at a 90-degree angle to the front plate so that the connectors are completely flush against the front plate. Lift up on the cables if necessary to keep the weight of the cables from dropping the connectors down to an incorrect angle, and use a flathead screwdriver to secure the data cable connector or a torque screwdriver to secure the clock cable connector.
Page 68
Base Cabinet Connecting Cables Between XB Units: FIGURE 3-34 3-40 SPARC Enterprise M8000/M9000 Servers Installation Guide • July 2010...
Page 69
Connecting Cables Between XB Units: Expansion Cabinet FIGURE 3-35 2. Connect XBU#0 and XBU#8 with the DT#0, DT#1, and DT#2 cables in this order. Use a flathead screwdriver to secure the data cable connectors. Note – Refer to the Note located before Step 1 when you connect the cable.
Page 70
5. Using hook and loop fasteners, secure the DT#3, DT#4, and DT#5 cables to the cable holder on the side of the expansion cabinet. For the position to fix, see (3) in FIGURE 3-35 Note – For XBU#8, giving consideration to facilitating CLKU maintenance, raise the cable a little before securing it in position.
Page 71
10. Using hook and loop fasteners, secure the DT#0, DT#1, and DT#2 cables to the cable holder along the side of the base cabinet. For the secured fastener location, see (6) of FIGURE 3-34 11. Connect XBU#1 and XBU#9 with the DT#3, DT#4, and DT#5 cables in this order. Use a flathead screwdriver to secure the data cable connectors.
Page 72
View After Completing Step 8 Step 14 FIGURE 3-36 15. Attach the next cable holder above the current cable holder, leaving one notch open between them. 16. Repeat Step 8 Step 14 to connect the cables between XBU#2 and XBU#10, and secure the cable with the cable holder (see FIGURE 3-37 3-44...
Page 73
Close-Up View of the Cable Connections FIGURE 3-37 Note – If the front cover of the expansion cabinet has been removed, attach it at this point. Chapter 3 Installing the Server 3-45...
3.4.4 Connecting the Administration Console The serial port of the eXtended System Control Facility (XSCF) unit is an RJ-45 interface port, which is used to monitor the boot process and make default settings. This port is monitored and configured with the administration console connected to the serial port by an RS232C cable (serial cable), which is a server accessory.
Page 75
Serial Port on the XSCF Unit of the M8000 Server FIGURE 3-38 Chapter 3 Installing the Server 3-47...
Serial Port on the XSCF Unit of the M9000 Server FIGURE 3-39 Checking the Input Power This section explains how to check the input power. 3-48 SPARC Enterprise M8000/M9000 Servers Installation Guide • July 2010...
3.5.1 Single-Phase Power Caution – Equipment damage – Each outlet must be in a circuit ranging from 200 to 240 VAC (30 A) and only be used for a power cord. An outlet to which a power cord is connected must be grounded. 1.
3.6.1 Switch On the Main Line Switches The main line switch is the input power switch for the server. This secction explains how to switch on the main line switches. 1. Set the mode switch on the operator panel to Service. Note –...
XSCF Unit LEDs FIGURE 3-41 1 2 3 3. Confirm that the ACTIVE LED (1) and READY LED (2) on the XSCFU#0 are lit. 3.6.2 Logging Into the XSCF Shell To make the initial setting of the XSCF, first use the default user account of the XSCF. Before an appropriate user account for the user environment is registered, log in by using the default user account and password.
Note – In the case that Step c is not performed within 1 minute, the login certification will expire. 3. Confirm that the XSCF Shell prompt is displayed. XSCF> 3.6.3 Initializing the XSCF Before each XSCF function is used, configurations and checks must be performed. This section explains the settings and checks concerning the items listed below.
Note – (4) To apply the specified configuration, execute the rebootxscf command and reset XSCF. 3.6.4 Checking for a Capacity on Demand (COD) Board If there is a COD board installed, run a diagnostic test on it. Note – When a COD board is installed, you can’t use the CPU before you install the hardware activation key (COD key).
3.7.1 Powering On the System To power on the system, follow the procedure below using the operator panel. Note – For details about each command, see the SPARC Enterprise M3000/M4000/M5000/M8000/M9000 Servers XSCF Reference Manual 1. Type the console -d 0 command at the XSCF Shell. This command switches the prompt from the XSCF console (XSCF>) to the domain console (#, the OS console).
9. Confirm that no error is displayed on the XSCF console as a result of the execution of either the fmdump or the showlogs command. When an error is displayed, see Section B.2, “Using Troubleshooting Commands” on page B-2. 3.7.2 Confirming XSCF Redundancy There are two XSCF units in the M8000/M9000 servers, and normally one of them is active and the other is on standby.
Page 84
XSCF> version -c xcp <Display example: XCP1060> XSCF#0 (Standby) XCP0 (Reserve):1060 XCP1 (Current):1060 XSCF#1 (Active) XCP0 (Reserve):1060 XCP1 (Current):1060 8. Enter the switchscf command in the XSCF Shell to switch XSCFU#1 from active back to standby. XSCF> switchscf -t Active The XSCF unit switch between the Active and Standby states.
3.7.3 Connecting an Ethernet Port The system control network enables you to connect the administration console to the XSCF unit. A direct connection can be established for this purpose. However, this type of connection is usually made through a hub or switch that is unique to the system control network.
Note – During login using SSH, you are prompted to confirm the authenticity of the fingerprint of the host public key. The reply is yes because no spoofing is assumed in this one-to-one connection. 4. Confirm that the XSCF Shell prompt (XSCF>) is displayed. 3.7.4 Verifying the Configuration Verify the hardware configuration by following the procedure below on the...
11. Confirm that the installed PCI card has been recognized. 12. Press the Enter, “#” (default escape character) , and “.” (period) keys. The #. key sequence switches the prompt from the domain console to the XSCF console. 3.7.5 Checking the Dual-Power Feed If the dual-power feed option is used, follow the procedure below to confirm that the system can operate even if one power feed is stopped.
3.7.6 Powering Off the System To power off the system, follow the procedure below on the administration console. 1. Type the poweroff -d 0 command at the XSCF Shell. XSCF> poweroff -d domain_ID (In this example, replace domain_ID with 0) 2.
C H A P T E R Connecting Your Domains to the Network and Running the SunVTS Software This chapter explains the following items which shows continuum of flow from a network connection for domain to a confirmation of hardware operation capabilities in SunVTS.
Page 90
Network Connections FIGURE 4-1 Fire wall Server IOU#0 XSCFU#0 User network Services remote Ethernet #1 IOUA LAN Ethernet #0 Switch Switch IOU#1 XSCFU#1 Ethernet #1 Ethernet #0 System control network Administration console SPARC Enterprise M8000/M9000 Servers Installation Guide • July 2010...
Page 91
Network Connections FIGURE 4-2 Fire wall Server Switch IOU#0 XSCFU#0 User network IOUA LAN Ethernet #1 IOUA LAN Ethernet #0 Switch Switch IOU#1 XSCFU#1 IOUA LAN Ethernet #1 IOUA LAN Ethernet #0 Switch System control network Administration console Chapter 4 Connecting Your Domains to the Network and Running the SunVTS Software...
Connecting the System to Each Network This section describes how to connect the M8000/M9000 servers to each network. To connect the server to the network, prepare one or more of the hubs, switches, and LAN cables required. 1. Connect one end of the Ethernet cable to the I/O unit. The Ethernet cable can be connected to either the LAN port of the IOUA or the LAN port of a LAN card installed in the I/O unit.
Page 93
IOUA LAN Port (Example) FIGURE 4-3 LAN port 0 LAN port 1 Chapter 4 Connecting Your Domains to the Network and Running the SunVTS Software...
Verifying a Network Connection This section explains how to confirm the connection of the user network in Section 4.2, “Connecting the System to Each Network” on page 4-4. 1. Set the mode switch on the operator panel to Service. 2. Press the POWER switch on the operator panel to power on the system. 3.
Page 95
Note – Solaris OS is pre-installed on the slot 0 of the hard disk drive (HDD) installed on I/O unit in slot 0. When you start Solaris OS from this HDD, a message appears to configure the Solaris OS in line with the environment in use. 1.
Verifying the Operation Using the SunVTS Software The SunVTS diagnostic software can be used to verify the hardware operation and to check the device connection status. This section explains how to install the SunVTS software and to verify the server’s operation.
Page 97
The SunVTS TTY Main Window FIGURE 4-5 TABLE 4-1 Window Item Control panel Status panel Message console Test_Groups panel Chapter 4 Connecting Your Domains to the Network and Running the SunVTS Software...
Page 98
Description of the TTY Keyboard TABLE 4-1 Description of Operation tab key Shifts the focus to another window. For example, when you press the tab key on the Control panel, the focus (highlighted part) is shifted to the Status panel, which is then framed by asterisks (*).
Page 99
9. Type the fmdump command or the showlogs error command at the XSCF Shell. 10. Confirm that no errors are displayed in the XSCF console after using the fmdump or the showlogs error commands. If an error is displayed, see Section B.2, “Using Troubleshooting Commands”...
A P P E N D I X System Views This appendix provides views of each model. Section A.1, “M8000 Server Views” on page A-2 ■ Section A.2, “M9000 Server Views” on page A-4 ■ Section A.3, “Power Cabinet Views” on page A-6 ■...
Page 102
M8000 Server Views M8000 Server - Front View FIGURE A-1 M8000 Server Unit Names (1 of 2) TABLE A-1 Name Abbreviation Power supply unit PSU#0 to #8 DC-DC converter DDC_A#0 DC-DC converter DDC_A#1 eXtended System Control Facility unit XSCFU_B#0 eXtended System Control Facility unit XSCFU_B#1 Tape drive unit TAPEU...
M8000 Server Unit Names (2 of 2) TABLE A-1 Name Abbreviation 3 FAN unit FAN_A#0 to #3 CPU memory board unit CMU#0 to #3 Power supply unit (for DPF) PSU#40 to #48 * Contact your sales representative for tape drive unit options on SPARC Enterprise M8000/M9000 servers. SPARC Enterprise M8000 Server - Rear View FIGURE A-2 M8000 Server Unit Names...
M9000 Server Views M9000 Server - Front View FIGURE A-3 SPARC Enterprise M9000 Server Unit Names (1 of 2) TABLE A-3 Name Abbreviation 2 FAN unit FAN_A#0 to #3, #20 to #23 AC section ACS_B#0, #1 Power supply unit PSU#0 to #14, #20 to #34 Crossbar unit (for base cabinet) XBU_B#0 to #7, #8 to #15 Clock control unit...
Page 105
SPARC Enterprise M9000 Server Unit Names (2 of 2) TABLE A-3 Name Abbreviation eXtended System Control Facility unit XSCFU_B#1 (M8000, M9000 for base cabinet) Tape drive unit TAPEU CD-RW/DVD-RW drive unit DVDU I/O unit IOU#0, #2, #4, #6, #8, #10, #12, #14 eXtended System Control Facility unit XSCFU_C#0 (For M9000 Expansion cabinet)
M9000 Server Unit Names TABLE A-4 Name Abbreviation 2 FAN unit FAN_A#4 to #15, #24 to #35 CPU memory board unit CMU#0 to #7, #8 to #15 I/O unit IOU#9, #11, #13, #15, #1, #3, #5, #7 Power Cabinet Views A.3.1 M8000 Server + Power Cabinet M8000 Server + Power Cabinet - Front View...
Page 107
M8000 Server + Power Cabinet Unit Names TABLE A-5 Name Abbreviation Power supply unit PSU#40 to #48 M8000 Server + Power Cabinet - Rear View FIGURE A-6 M8000 Server + Power Cabinet Unit Name TABLE A-6 Name Abbreviation AC section ACSTPH#0, ACSTPH#1 Appendix A System Views...
A.3.2 M9000 Server + Power Cabinet M9000 Server + Power Cabinet - Front View FIGURE A-7 Base side power cabinet Expansion side power cabinet * For single-phase M9000 Server + Power Cabinet Unit Names TABLE A-7 Name Abbreviation Power supply unit PSU#40 to #54, #60 to #74 AC section ACS_B#20 to #24, #30 to #34...
Page 109
M9000 Server + Power Cabinet - Rear View FIGURE A-8 Expansion side power cabinet Base side power cabinet * For three-phase M9000 Server + Power Cabinet Unit Name TABLE A-8 Name Abbreviation AC section ACSTPH#0, ACSTPH#1 (for three-phase) Appendix A System Views...
Operator Panel Overview You can use the operator panel to view the operating status of the SPARC Enterprise system as a whole and perform operations such as system power operations. You can use it while the cabinet doors are closed. The following figure shows the appearance of the operator panel.
Page 111
LEDs and Switches on the Operator Panel (Continued) TABLE A-9 Icon Name Description POWER switch Switch to direct server power on/power off. Mode switch The Locked setting: Normal operation mode • The system can be powered on with the POWER switch, but it cannot be powered off with the POWER switch.
A P P E N D I X Troubleshooting This appendix explains how to deal with possible problems during system installation. Section B.1, “Actions to Take for Common Problems” on page B-1 ■ Section B.2, “Using Troubleshooting Commands” on page B-2 ■...
fieldeng privilege for the maintenance work. If our engineer asks you to supply this permission, please take appropriate action to ensure that the engineer can perform the required work. In the event that problems occur, the methods of troubleshooting may vary depending on the SPARC Enterprise system operating status and the nature of the problem.
B.2.1 Using the showhardconf Command The showhardconf command displays information about each FRU, including the following information: Current configuration and status ■ Number of installed FRUs ■ Domain information ■ External I/O Expansion Unit information ■ Name properties of PCI cards ■...
Page 119
Example showhardconf Command Output (5 of 5) EXAMPLE B-1 SWBP#0 Status:Normal; Ver:0101h; Serial:PP0607E759 + FRU-Part-Number:CA20394-B16X 001AA MEDBP#0 Status:Normal; Ver:0101h; Serial:PP06058497 + FRU-Part-Number:CA20394-B17X 002AB Refer to the showhardconf(8) man page for more information. Example showhardconf -u Command Output EXAMPLE B-2 XSCF> showhardconf -u SPARC Enterprise M9000;...
B.2.2 Using the showlogs Command The showlogs command will display the contents of a specified log file in the order of the timestamp, starting with the oldest date. The showlogs command can display the following logs: Error log ■ Power log ■...
In this example, a CPU module and memory module in a CPU memory unit are degraded. XSCF> showstatus CMU#0; CPUM#0-CHIP#0 Status:Faulted; MEM#00A Status:Faulted; XSCF> B.2.4 Using the fmdump Command The fmdump command can be used to display the contents of any log files associated with the Solaris fault manager.
B.2.4.2 Using the fmdump -e Command To get information about the errors that caused this failure, use the -e option with the fmdump command. # fmdump -e TIME CLASS Nov 02 10:04:14.3008 ereport.io.fire.jbc.mb_per B-10 SPARC Enterprise M8000/M9000 Servers Installation Guide • July 2010...
B.2.5 Using the fmadm faulty Command The fmadm faulty command can be used by administrators and service personnel to view and modify system configuration parameters that are maintained by the Solaris Fault Manager. The fmadm faulty command is primarily used to determine the status of a component involved in a fault.
B.2.6 Using the fmstat Command The fmstat command can report statistics associated with the Solaris fault manager. The fmstat command shows information about DE performance. In the example below, the eft DE (also seen in the console output) has received an event which it accepted.
B.3.1.1 iostat Command Options describes options for the iostat command and how those options can TABLE B-3 help troubleshoot the server. Options for iostat TABLE B-3 Option Description How It Can Help No option Reports status of local I/O devices. A quick three-line output of device status.
The prtdiag command is located in the /usr/platform/platform-name/sbin/ directory. Note – The prtdiag command might indicate a slot number different than that identified elsewhere in this document. This is normal. B.3.2.1 prtdiag Command Options describes options for the prtdiag command and how those options can TABLE B-4 help troubleshooting.
Page 127
========================= IO Cards ========================= Name Model ---- ------ ------------------------- scsi LSI,1064 network network scsi LSI,1064 network network ==================== Hardware Revisions ==================== System PROM revisions: ---------------------- OBP 4.24.4 2007/11/05 10:27 =================== Environmental Status =================== Mode switch is in UNLOCK mode =================== System Processor Mode =================== SPARC64-VII mode Appendix B Troubleshooting...
B.3.3 prtconf Command Similar to the show-devs command run at the ok prompt, the prtconf command displays the devices that are configured. The prtconf command identifies hardware that is recognized by the Solaris OS. If hardware is not suspected of being bad yet software applications are having trouble with the hardware, the prtconf command can indicate if the Solaris software recognizes the hardware, and if a driver for the hardware is loaded.
# prtconf System Configuration: Sun Microsystems sun4u Memory size: 32768 Megabytes System Peripherals (Software Nodes): SUNW,SPARC-Enterprise scsi_vhci, instance #0 packages (driver not attached) SUNW,builtin-drivers (driver not attached) deblocker (driver not attached) disk-label (driver not attached) terminal-emulator (driver not attached) obp-tftp (driver not attached) ufs-file-system (driver not attached) chosen (driver not attached) openprom (driver not attached)
Options for netstat TABLE B-6 Option Description How It Can Help Displays the interface state, including packets Provides a quick overview of the network in/out, error in/out, collisions, and queue. status. interval Providing a trailing number with the option Identifies intermittent or long duration repeats the netstat command every interval network events.
B.3.5.1 ping Command Options describes options for the ping command and how those options can help TABLE B-7 troubleshooting. Options for ping TABLE B-7 Option Description How It Can Help hostname The probe packet is sent to hostname and Verifies that a host is active on the returned.
B.3.6.1 ps Command Options describes options for the ps command and how those options can help TABLE B-8 troubleshooting. Options for ps TABLE B-8 Option Description How It Can Help Displays information for every process. Identifies the process ID and the executable.
B.3.7.1 prstat Command Options describes options for the prstat command and how those options can TABLE B-9 help troubleshooting. Options for prstat TABLE B-9 Option Description How It Can Help No option Displays a sorted list of the top processes that are Output identifies process ID, user ID, consuming the most CPU resources.
Need help?
Do you have a question about the Oracle Sun SPARC Enterprise M8000 and is the answer not in the manual?
Questions and answers