1. Manuals
  2. Brands
  3. FTE Maximal Manuals
  4. Control Unit
  5. TSF 310 CI
  6. User manual

FTE Maximal TSF 310 CI User Manual

Hide thumbs

Advertisement

Table of Contents

TSF 310 CI
USER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TSF 310 CI and is the answer not in the manual?

Questions and answers

Summary of Contents for FTE Maximal TSF 310 CI

  • Page 1 TSF 310 CI USER’S MANUAL...

  • Page 2: Box Content

    User’s manual · TSF 310 CI NOTE: This user’s guide is adapted to software version v.0.1.47 of TSF 310 CI dated 09/04/2014. For future software updates, you can download the user’s guide from the following website: http://www.ftemaximal.com/ Chapter 1. Installation.

  • Page 3: Description And Connections

    1.3. Description and connections The module TSF 310 CI is used for the reception of free channels that obey the DVB-S/DVB-S2 standards. Each module allows the reception of a complete transponder in DVB-S (QPSK) / DVB-S2 (QPSK/8PSK), and the subsequent modulation in DVB-T (COFDM) of it.
  • Page 4 1.4. Programming TSF 310 CI has two ethernet connectors. In order to make the programming of the module you have to connect the corresponding programmer to PRO 201 connector. You can make the programming through the PRO 201, PRO 300 programmers and also through the mediaMAX EVO and mediaMAX MINI field strength meter.
  • Page 5 PRO 201and PRO 300. mediaMAX EVO / mediaMAX MINI In order to start programming the TSF 310 CI transmodulator, you will have to go to “Tools” option through the key 8 of your field strength meter and to select the “Transmodulator Prog.“ option.
  • Page 6 User’s manual · TSF 310 CI If you have a module with a serial number higher than 075511441882 it will allow you to choose between two units with an only device connected to the programmer (Unit 1 or Unit 2.) 2.
  • Page 7 User’s manual · TSF 310 CI - DiseqC Switch: A, B, C, D and Off. 4. Modulator Set Up This option allows configuring the DVB-T/DVB-H modulator of the device. - Bandwidth: Selection of the Bandwidth of the modulated signal: 8MHz, 7MHz, 6MHz and 5MHz.The 5MHz option is only supported by DVB-H standard.
  • Page 8 User’s manual · TSF 310 CI - NM low Limit (dB): An event of error will be recorded when the value of Noise Margin is lower than the set value. - NM high limit (dB): Once the event of error is recorded (Noise Margin <...
  • Page 9 User’s manual · TSF 310 CI 7. Program management - New program: This option allows creating a program with the current configuration of a module or group of modules. - Load program: It allows loading a previously created program on a module or group of modules.
  • Page 10 User’s manual · TSF 310 CI Excessive capacity Recomendad capacity It is recommended to remove (lower to 85%) services Removing services: 1. Select the “Service to remove” 2. Select one of the transponder 3. Once you have chosen the service, option.
  • Page 11 User’s manual · TSF 310 CI - Services: - Change service name: It allows changing the name of the service manually. In order to do so, please choose the service in the first line and then write the new name in the second line.
  • Page 12 User’s manual · TSF 310 CI PRO 201 Note: From PRO 201 programmer you can only carry out the programming of a single module, in order to carry out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX MINI series field strength meter.
  • Page 13 User’s manual · TSF 310 CI Terrestrial modulation (Out Terr) These options allow configuring the DVB-T/DVB-H modulator of the device. TSF310CI *Out Terr - Modulation: Output modulation format: 4 QAM, 16 QAM, 64 QAM. Modulation: - Invert (Spectrum inversion): Activate or deactivate the spectrum reverse in the >Invert:...
  • Page 14 User’s manual · TSF 310 CI - Write to module: It loads in the module one of the configurations previously saved in the memory of the programmer. The steps to make a correct configuration of the headend are specified below:...
  • Page 15 User’s manual · TSF 310 CI - Add Services TSF310CI TSF310CI TSF310CI BW usage 000% Input 000% Delete services PID:06200 arte HD Operation finish +Add >Add services 1. Select the option “Add services” 2. Select one of the transponder 3. A window will appear and it will let through Up/Down buttons.
  • Page 16 User’s manual · TSF 310 CI PRO 300 Note: From PRO 300 programmer you can only carry out the programming of a single module, in order to carry out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX MINI series field strength meter.
  • Page 17 User’s manual · TSF 310 CI Terrestrial modulation (Out Terr) These options allow configuring the DVB-T/DVB-H modulator of the device. Out terr - Modulation: Output modulation format: 4 QAM, 16 QAM, 64 QAM. - Invert (Spectrum inversion): Activate or deactivate the spectrum reverse in 1.Modulation...
  • Page 18 User’s manual · TSF 310 CI -.Adding Services: Output services Output services Output services 1.Add services PID :01105 RAI 2 2.Delete services 1.Add Operation finish BW usage 000% BW usage 072% TSF310CI Mux 0 TSF310CI Mux 0 TSF310CI Mux 0 1.
  • Page 19 User’s manual · TSF 310 CI Network Option: This option allows adjusting the identification parameters of Network options multiplex. 1.Network name -Network name: Associated name to the network. 2.TSID - TSID: Identification value of Transport Stream. Give a different value of TSID 3.NID...
  • Page 20 User’s manual · TSF 310 CI - Write to module: It loads in the module one of the configurations previously saved in the memory of the programmer. The steps to make a correct configuration of the headend are specified below:...
  • Page 21 Installation that consist of 6 TSF 310 CI and that will allow tuning channels up to 6 different transponders and to distribute them through a TV network in DVB-T. The new models TSF 310 CI with twin output allow distributing up to 12 multiplex in the installation.

  • Page 22: Technical Features

    User’s manual · TSF 310 CI Wide band amplifier 47-862MHz Parabolic antenna Mod. AMP 310 P Code 2003520 Chapter 2. Technical features Ref. TSF 310 CI Code 2003544 Input frequency margin 950-2150 MHz Input level -25 to -65 dBm Imput impedance...

  • Page 23: Fft Mode

    User’s manual · TSF 310 CI ATACHMENT I Depending on the configured parameters we are going to obtain one particular channel capacity (output useful bit rate). In order to make an estimation of this output bits rate, we have to take into account the following parameters:...
  • Page 24 User’s manual · TSF 310 CI Useful channel capacity (8 MHz) Guard Interval Modulation FEC codification 1/16 1/32 4.976 5.529 5.855 6.032 6.635 7.373 7.806 8.043 QPSK 7.465 8.294 8.782 9.048 8.294 9.216 9.758 10.053 8.709 9.676 10.246 10.556 9.953 11.059...
  • Page 25 ESPAÑA FRANCE ITALIA Corrals Nous, 77 Fte maximal France SAS Via Edison, 29 Pol. Industrial Can Roqueta 7 avenue du Pont de Tasset 42040 Calerno di 08202 Sabadell 74960 MEYTHET Sant’Ilario d’Enza (RE) (Barcelona) España Tel. +33.4 50.68.80.17 Tel. 00 39 05 22 90 97 01 Tel.

Table of Contents