GE PDW7700G00BB Installation Instructions Manual
GE PDW7700G00BB Installation Instructions Manual

GE PDW7700G00BB Installation Instructions Manual

Built-in
Hide thumbs Also See for PDW7700G00BB:

Advertisement

Quick Links

This Owner's Manual is provided and hosted by Appliance Factory Parts.
GE PDW7700G00BB
Owner's Manual
Shop genuine replacement parts for GE
PDW7700G00BB
Find Your GE Dishwasher Parts - Select From 6722 Models
-------- Manual continues below --------

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PDW7700G00BB and is the answer not in the manual?

Questions and answers

Summary of Contents for GE PDW7700G00BB

  • Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. GE PDW7700G00BB Owner's Manual Shop genuine replacement parts for GE PDW7700G00BB Find Your GE Dishwasher Parts - Select From 6722 Models -------- Manual continues below --------...
  • Page 2: Installation Instructions

    Product failure Read and observe all CAUTIONS and WARNINGS due to improper installation is not covered under the shown throughout these instructions. While performing GE Appliance Warranty. installations described in this booklet, gloves, safety Completion Time – •...
  • Page 3: Parts Supplied

    Installation Preparation Trim Pieces PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop or to side of cabinetry. (Taped to top or side of dishwasher.) Side and top trim pieces 2 Wood Screws 4, #8 Pan head Phillips Screws Side Mounting Brackets 2 Side mounting brackets with 4 mounting screws 3/8"...
  • Page 4: Prepare Dishwasher Enclosure

    Installation Preparation PREPARE DISHWASHER ENCLOSURE • The dishwasher must be installed so that drain hose is no more than 10 feet in length for proper drainage. • The dishwasher must be fully enclosed on the top, sides and back, and must not support any part of the This Wall Area enclosure.
  • Page 5: Prepare Electrical Wiring

    Installation Preparation PREPARE ELECTRICAL WIRING FOR PERSONAL SAFETY: Remove Alternate house fuse or open circuit breaker Receptacle before beginning installation. Do not Location use an extension cord or adapter plug 18" with this appliance. 1-1/2" Dia. Hole (Max.) Receptacle Location 18"...
  • Page 6: Prepare Hot Water Line

    Installation Instructions STEP 1 CHECK DOOR BALANCE PREPARE HOT WATER LINE • The line may enter from either side, rear or floor With dishwasher on wood skid, check the door balance within the shaded area shown in Figure F. by opening and closing the door. •...
  • Page 7: Step 3 Remove Toekick

    Installation Instructions STEP 3 REMOVE TOEKICK STEP 5 INSTALL 90° ELBOW • Remove the two toekick screws. • Wrap 90° elbow with thread seal tape. • Install a 90° elbow onto the water valve. Front of Dishwasher Remove 2 Toekick Screws Water Valve Bracket Figure I...
  • Page 8: Step 7 Insert Drain Hose Through Cabinet

    Installation Instructions STEP 9 INSTALL TRIM PIECES STEP 7 INSERT DRAIN HOSE THROUGH CABINET Skip this step if trim is not supplied with the dishwasher. • Locate trim strips inside dishwasher. • Upright the dishwasher and position in front of the •...
  • Page 9: Step 12 Position Dishwasher, Secure To Cabinet

    Installation Instructions STEP 11 LEVEL DISHWASHER • Level the dish- Access Hole washer by adjusting IMPORTANT – Dishwasher must be level for proper the four leveling dish rack operation and wash performance. legs individually. • If adjustment to the • Place level on right rear leveling door and rack leg is required,...
  • Page 10: Step 13 Connect Water Supply

    Installation Instructions Compression Nut STEP 13 CONNECT WATER SUPPLY Ferrule Connect water supply line to 90° elbow. • Slide compression nut, then ferrule over end of water line. Hot Water Supply Line 90° Elbow • Insert water line into 90° elbow. •...
  • Page 11: Step 15 Connect Power Supply

    Installation Instructions STEP 15 CONNECT POWER STEP 16 PRE-TEST CHECK LIST SUPPLY Review this list after installing your dishwasher to avoid charges for a service call that is not covered by Skip this step if equipped with power cord your warranty. Verify that power is turned off at the source.
  • Page 12: Step 17 Dishwasher Wet Test

    Installation Instructions STEP 17 DISHWASHER WET TEST STEP 18 REPLACE TOEKICK Turn on power supply (or plug power cord into • Place toekick against the legs of the dishwasher. outlet, if equipped). Latch door. Push “Normal Wash” button. Push start/reset pad once. Check to be sure that water enters the dishwasher.
  • Page 13 Pub. No. 31-30530 Dwg. No. 206C1559P070 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE (N.D. 212) 6/01...

Table of Contents