Contents Safety information What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING IMPORTANT SAFETY INSTRUCTIONS Warnings Cautions Regulatory notice FCC Notice IC Notice Open Source Announcement Installation requirements Key installation requirements Location considerations Ducting requirements Exhausting requirements Gas requirements...
Page 3
Operations LCD panel Operating a cycle Cycle overview Settings Special features Drying guide Maintenance Cleaning Troubleshooting Checkpoints Information codes Specifications Fabric care chart Protecting the environment Specification sheet English 3 Untitled-1 3 Untitled-1 3 2025-04-23 2025-04-23 11:33:29 11:33:29...
Safety information Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features.
Page 5
WARNING - Risk of Fire • Clothes dryer installation must be performed by a qualified installer. • Install the clothes dryer according to the manufacturer’s instructions and local codes. • Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
Page 6
Safety information WARNING - To reduce the risk of fire or explosion: • Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode.
WARNING - Fire or explosion hazard • Failure to follow safety warnings exactly could result in serious injury, death or property damage. • Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance. •...
Safety information IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapours that could ignite or explode.
Warnings WARNING • Ensure pockets are free of small, irregularly shaped hard objects and foreign material, i.e. coins, knives, pins, etc. These objects could damage your dryer. • Gas leaks may occur in your system, resulting in a dangerous situation. Cautions CAUTION •...
Page 10
Safety information • Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough to catch fire.
Regulatory notice FCC Notice CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1.
Regulatory notice IC Notice The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Directive 2014/53/EU . The full text of the EU declaration of conformity is available at the following internet address: The official Declaration of conformity may be found at http://www.samsung.com, go to Support > Search Product Support and enter the model name.
Installation requirements Read through the following instructions before installing the dryer and keep this manual for future reference. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve.
Page 15
Dimensions Type Front loading dryer Models DV90F53A** A. Overall height 38.7 (984) B. Width 27.0 (686) Dimensions (in. (mm)) C. Depth with door open 53.1 (1348) D. Depth 31.4 (798) English 15 Untitled-1 15 Untitled-1 15 2025-04-23 2025-04-23 11:33:31 11:33:31...
Page 16
Installation requirements Clearance requirement This clearance requirement is applicable for dryers only. NOTE • For washer's clearance requirement, see the washer's user manual. • If the washer and dryer have different clearance requirements, use the one with the larger value. Alcove or closet installations WARNING •...
Page 17
Undercounter installation 39.6 in. (1006 mm) 1 in. (25 mm) 1 in. (25 mm) Pedestal installation 4 in. (102 mm) 6 in. (152 mm) 52.8 in. (1341 mm) English 17 Untitled-1 17 Untitled-1 17 2025-04-23 2025-04-23 11:33:31 11:33:31...
Page 18
NOTE Stacking (DV90F53A** : SKK-RW*) Many of Samsung's washers and dryers can be stacked to maximize usable space. You can purchase an optional stacking kit from your Samsung retailer. For details about stacking and compatible models, refer to the user manual included in the stacking kit you purchase.
Ducting requirements Use only for short-run Recommended installation Weather hood type 4” (10.2 cm) 2.5” (6.4 cm) No. of 90° elbows Rigid Rigid 80 ft. (24.4 m) 74 ft. (22.6 m) 68 ft. (20.7 m) 62 ft. (18.9 m) 57 ft. (17.4 m) 51 ft.
Installation requirements Exhausting requirements The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room.
Gas requirements WARNING • Use only natural or LP (liquid propane) gases. • The installation must be conformed with local codes, or in the absence of local codes, with the national fuel gas code, ANSI Z223.1/NFPA 54, latest revision(for the UNITED STATES), or with the natural gas and propane installation code, CSA B149.1(for Canada).
Installation requirements Electrical requirements The wiring diagram is located on the plate under the control panel or rear frame. WARNING • Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded.
Electrical connections Before operating or testing, follow all grounding instructions in the “ Grounding” section. An individual branch (or separate) circuit serving only your dryer is recommended. Do not use an extension cord. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required. Electric models –...
What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the parts, contact a local Samsung customer center or the retailer. 01 Worktop 02 Control panel...
Page 25
Parts supplied Y-connector Short water hose Tools needed for installation Pliers Cutting knife Pipe wrench Nut screwdriver (gas models only) Level Phillips screwdriver Duct tape Wrench LPG-safe compound or Teflon Tape (for gas installation) WARNING Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.
Installation Step-by-step installation Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. • Do not remove the protective film on the door before completing the product installation. If you remove the protective film before the installation is complete, the door may get scratched or damaged during installation.
Page 27
STEP 3 Connect the electrical wiring (for electric models) Before connecting the electrical wiring, make sure you have read the “ Electrical requirements” section on page 22. 3-wire system 1. Loosen or remove the screws from the center terminal block. 2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block.
Page 28
Installation 4-wire system 1. Remove the external ground connector’s screw and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
Page 29
STEP 4 Connect the water hose The dryer must be connected to a cold water tap using a water hose. A water hose is not provided with the dryer and therefore you must purchase it separately. 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose.
Page 30
Installation Using the short hose as an extension 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight.
Page 31
STEP 5 Level the dryer To ensure optimal performance, the dryer must be level. Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, turn the leveling feet (B) clockwise to lower the dryer or counterclockwise to raise the dryer.
Page 32
Installation STEP 6 Power on (for gas models) Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 7 below.
Vent Blockage Test After the dryer is installed, run the Vent Blockage Test function to check if the duct system is properly installed. Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy. NOTE The Vent Blockage Test function must run when the dryer is cool.
Installation Exhaust ducting guide Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping screws. 3. To facilitate the exhaust, keep the ducts as straight as possible. Cleaning Clean all old ducts before installing the dryer, and make sure the vent flap opens and closes freely.
Page 35
6. Remove the two screws above and below the lever holder on the opposite side of the door opening. 7. Remove the two screws that hold the lever holder in place, and then remove the lever holder. 8. Re-insert the two screws that held the lever holder into the same screw holes, and then tighten.
Page 36
Installation 10. Push the lever holder into the cut out on the other side of the door opening. Insert screws, and then tighten as shown. 11. Re-attach the remaining screws to the remaining holes above and below the lever holder, and then tighten.
Before you start Initial setup • When you turn on the dryer for the first time, the screen shows the initial setup process. Follow the on- screen instructions to complete it. • Once you select a language, the language selection screen will not reappear. You can change the language settings by swiping down from the top of the screen to access the Quick Panel , then tapping >...
Before you start Sort and load • Put one wash load in the dryer at a time. • Do not mix heavy and lightweight items together. • To improve drying efficiency for one or two items, add a dry towel to the load. •...
Remove the drying rack from its packaging and store the rack for later use. If a drying rack is not provided, you can purchase it at a local Samsung service center. (Part Code : DC93- 00374G) To use the drying rack, follow these steps: 1.
Operations WARNING To reduce the risk of fire, electric shock, or injury to persons, read the Safety information before operating the dryer. LCD panel Tap to turn the dryer on or off. 01 Power The display shows current cycle information and estimated time remaining, or 02 Display an information message when a problem occurs.
Page 41
Display icon descriptions Home Tap to go to the Home screen. Tap to enter the Settings menu. Settings • For more information on Settings, see page 48. Lock This icon indicates the screen is locked. Smart Control / Smart This icon indicates that the Smart Control / Smart Monitor is on. Monitor Wi-Fi Tap to turn on or off the Wi-Fi .
Operations Operating a cycle 1. Tap to turn the power on. 2. Select the desired cycle. For more information on Cycle overview, see page 43. 3. Change the default cycle options. Tap Dryness , Dry Time , Drying Temp , Damp Alert , Wrinkle Prevent , Eco Dry , or Anti Static to change the default cycle settings.
Cycle overview Cycle descriptions You can add or delete cycles to personalize the cycle list by swiping down from the top of the screen to access the Quick Panel , then tapping > Dryer > My cycles. See page 52 for more information. NOTE •...
Page 44
Operations Cycle Description Shirts • Use to dry a few items such as a shirt quickly. • For machine washable and tumble dryable wool only. Wool • For best results, turn laundry inside out before drying. • Dry wrinkle-free cotton, synthetic fabrics, knits, and permanent Perm Press press fabrics automatically.
Cycle options You can change the following options for your dry cycles. Some options may be unavailable depending on the selected cycle. Option Description • Tap to change the dry level for the selected cycle. You can select Dryness from level Damp to Very, but available level depends on the selected cycle.
Operations Cycle chart NOTE : factory setting, : can be selected Cycle Recommended items Time Drying Temp Normal Cotton, mixed loads of cotton and synthetic fabrics Medium AI OptiDry+ Cotton, mixed loads of cotton and synthetic fabrics Medium Time Dry Any load High (Extra Low~High)
Page 47
NOTE : factory setting, : can be selected Dryness Option Cycle Damp Wrinkle Very More Normal Less Damp Eco Dry Anti Static Alert Prevent Normal AI OptiDry+ Time Dry ...
Settings menu description General Options Descriptions You can log in to your Samsung account or create a new Samsung Samsung account account. You can turn the Wi-Fi on or off. You can also use the Easy Connection to connect your dryer to the SmartThings app to use the Smart Control function.
Page 49
Options Descriptions You can lock the dryer’s control to prevent children or infants from accidentally starting the dryer or changing its settings. • When this function is enabled, the touch screen become locked for safety. • You can enable or disable this function in any selected cycle. •...
Page 50
You can check the dryer's internal storage space. Security status of your You can check the security status of all devices logged into your devices Samsung account. Language You can change the system language. You can set the time and date automatically or manually and set the Date and time desired time format.
Page 51
Options Descriptions You can set the Voice guide and Visibility enhancements settings. • Voice guide : Enable this feature to receive voice guidance from your dryer. Turn on the power, swipe down from the top of the screen to access the Quick Panel , then tap - Accessibility - Voice guide - Turn On to enable the feature.
Page 52
Operations Options Descriptions You can check the information of the dryer such as Status and Legal About device information. Dryer Settings Descriptions This turns on the light inside the drum so you can check the items Drum light inside. This function saves frequently used cycles and settings. When you turn the function on, the dryer remembers the cycles you use most and their settings ( Dryness , Dry Time , and Temperature ) and displays them in frequency order.
Special features Smart Control You can connect to the SmartThings app and control your dryer remotely. Connecting your dryer ( Smart Control for electric model, Smart Monitor for gas model) 1. Download and open the SmartThings app on your smartphone or tablet (Android & iOS). 2.
Page 54
• This appliance supports the Wi-Fi 2.4 GHz & 5.0 GHz protocols. Download On an app market (Google Play Store, Apple App Store, Samsung Galaxy Apps), find the SmartThings app by searching for “ SmartThings ”. Download and install the app on your device.
Drying guide The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference. Items Description Follow the care label instructions or dry using Bedding. Bedspreads &...
Maintenance Keep the dryer clean for best performance and to lengthen its life cycle. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve.
Page 57
Vent sensor The dryer features a vent sensor that detects and notifies you when it is time to clean the ductwork. Check the following if you get the “ Check the lint filter or vent condition ” message when you turn on the dryer. NOTE •...
Troubleshooting Checkpoints If you encounter a problem with the dryer, first check the table below and try the suggestions. Problem Action • Make sure the dryer is plugged in. • Make sure the door is properly closed. Dryer does not start. •...
Page 59
Problem Action • Look for coins, loose buttons, nails, and other objects and remove them immediately. • Check the lint filter. Remove any items stuck inside the lint filter. • Make sure the dryer is level and standing firmly on the floor. The dryer is too loud.
• If this information code remains, contact a Samsung service center. Incorrect door switch. Contact a Samsung service center. If any information code keeps appearing on the display, contact a Samsung service center. English Untitled-1 60 Untitled-1 60 2025-04-23...
Specifications Fabric care chart The following symbols provide garment care direction. The clothing care labels include symbols for drying. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to optimize garment life and reduce laundering problems. Tumble Dry Cycles Normal Permanent Press...
Specifccaiion Protecting the environment This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance.
Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale and/or proof of delivery must be presented upon request to SAMSUNG or SAMSUNG’s authorized service center to receive warranty service.
Page 64
Visits by an authorized servicer to explain product functions, maintenance or installation are not covered by this limited warranty. Please contact SAMSUNG at the number below for assistance with any of these issues.
Page 65
LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center. SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability within the Canada.
Page 67
(English) www.samsung.com/ca_fr/support (French) Visits by a Service Engineer to explain functions, maintenance, or installation is not covered by warranty. Please contact the Samsung call center at the number above for help with any of these issues. English 67 Untitled-1 67...
Page 68
If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com/us/support www.samsung.com/ca/support (English) CANADA 1-800-Samsung (726-7864) www.samsung.com/ca_fr/support (French) Untitled-1 68 Untitled-1 68...
Need help?
Do you have a question about the DV90F53A Series and is the answer not in the manual?
Questions and answers