Sharp GX17r Service Manual
Sharp GX17r Service Manual

Sharp GX17r Service Manual

Digital mobile phone
Table of Contents

Advertisement

Quick Links

Servicing Concerns ................................ . ............i
[1]
Specifications ......................................... . ....... 1-1
[2]
Names of parts....................................... . ....... 1-2
[3]
Quick Start Guide ................................... . ....... 1-3
[4]
Optional Accessories ............................. . ....... 1-5
[1]
[2]
Test points .............................................. . ..... 2-40
[3]
Troubleshooting ..................................... . ..... 2-42
CHAPTER 3. DISASSEMBLY AND REASSEMBLY
[1]
Servicing Concerns ................................ . ....... 3-1
[2]
Disassembly and reassembly ................ . ....... 3-3
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
CONFIDENTIAL
SERVICE MANUAL
Refer to the section "Identification of GX17 and GX17(r) version".
INTERNAL
SELEC-
MODEL
TION
NAME
CODE
TQE17CAW
CAW
Australia: Black
TQE17CBW
CBW
Hungary: Black
TQE17CDW
CDW
Greece: Black
TQE17CEW
CEW
U.K.: Black
TQE17CFW
CFW
France: Black
TQE17CLW
CLW
Malta: Black
TQE17CMW
CMW
Romania: Black
TQE17CNW
CNW
Cyprus: Black
TQE17CQW
CQW
Iceland: Black
TQE17CSA
CSA
Spain: Blue
TQE17CSW
CSW
Spain: Black
• In the interests of user-safety the set
should be restored to its original condition
and only parts identical to those specified
should be used.
CONTENTS
DIGITAL MOBILE PHONE
MODEL
DESTINATION:
INTERNAL
COLOUR
MODEL
NAME
TQE17CTW
TQE17CUW
TQE17CZW
TQE17PEW
TQE17PMW
TQE17PPA
TQE17PPW
• Caution
Risk of explosion if battery is replaced by
an incorrect type, dispose of used batter-
ies according to the instruction.
[1]
Block diagram (Main).....................................4-1
[2]
Block diagram (RF)........................................4-2
[3]
Block diagram (Power supply) .......................4-3
CHAPTER 5. SCHEMATIC DIAGRAM AND WIRING
SIDE OF P.W.BOARD
[1]
Notes on schematic diagram .........................5-1
[2]
Types of transistor and LED ..........................5-1
[3]
Waveforms of circuit ......................................5-1
[4]
Schematic diagram (Main 1/5).......................5-2
[5]
Schematic diagram (Main 2/5).......................5-3
[6]
[7]
Schematic diagram (Main 5/5).......................5-5
[8]
Wiring side of P.W.Board (Main) ....................5-6
[9]
P.W.Board (Key) ............................................5-7
[10] Voltage value .................................................5-8
[1]
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
GX17
No. S0619TQE17REF
GX17
(r) Version
SELEC-
DESTINATION:
TION
COLOUR
CODE
CTW
Italy: Black
CUW
Belgium: Black
CZW
New Zealand: Black
PEW
U.K. (Prepaid):
Black
PMW
Romania (Prepaid):
Black
PPA
Portugal (Prepaid):
Blue
PPW
Portugal (Prepaid):
Black

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GX17r and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sharp GX17r

  • Page 1: Table Of Contents

    CHAPTER 2. ADJUSTMENTS, PERFORMANCE Schematic diagram (Main 1/5).......5-2 CHECK, AND FIRMWARE UPGRADE Schematic diagram (Main 2/5).......5-3 SHARP Programme Support Tool (SPST) ..2-1 Schematic diagram (Main 3/5 / Main 4/5)..5-4 Test points ............ 2-40 Schematic diagram (Main 5/5).......5-5 Wiring side of P.W.Board (Main) ....5-6...
  • Page 2: Servicing Concerns

    Specifications Label Servicing Concerns 1. When requested, back-up user’s handset data using SPST (SHARP Programme Support Tool). Otherwise, before servicing, warn the user that data in the memory may be lost during repairs. 2. Upgrade the firmware to the latest version using SPST before returning the handset to the customer.
  • Page 3: Precautions For Using Lead-Free Solder

    GX17 CONFIDENTIAL PRECAUTIONS FOR USING LEAD-FREE SOLDER Employing lead-free solder This model employs lead-free solder. This is indicated by the “LF” symbol printed on the PWB and in the service manual. The suffix letter indicates the alloy type of the solder. Example: Indicates lead-free solder of tin, silver and copper.
  • Page 4: Chapter 1. General Description

    The Bluetooth word mark and logos are owned by the trademarks of Aplix Corporation in Japan Bluetooth SIG, Inc. and any use of such marks by Sharp is and other countries. under license. Other trademarks and trade names are those of their respective owners.
  • Page 5: Names Of Parts

    GX17 CONFIDENTIAL [2] Names of parts 1. Earpiece 10.End/Power Key: Ends a call, turns power on/ 2. Navigation Keys (Arrow Keys): off. 11.Keypad Moves cursor to select 12.# Key: menu items, etc. Switches symbol screens. Press and hold this key on Up/Down arrow keys: Displays Contacts List the text entry screen to shift entries in standby mode.
  • Page 6: Quick Start Guide

    GX17 CONFIDENTIAL [3] Quick Start Guide The following is a sample quick start guide (Quick Start Guide for the UK model). 1 – 3...
  • Page 7 GX17 CONFIDENTIAL 1 – 4...
  • Page 8: Optional Accessories

    GX17 CONFIDENTIAL [4] Optional Accessories Li-ion Spare Battery (XN-1BT30) Cigarette Lighter Charger (XN-1CL30) USB Data Cable (XN-1DC30) AC Charger (XN-1QC30, XN-1QC31 , XN-1QC32 ) Personal Hands-free Kit (XN-1ER20) The above accessories may not be available in all regions. For details, please contact your dealer. 1 –...
  • Page 9: Chapter 2. Adjustments, Performance Check, And Firmware Upgrade

    ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE SPST (SHARP Programme Support Tool) allows you to adjust settings, conduct performance checks, and upgrade the firmware. [1] SHARP Programme Support Tool (SPST) SPST (SHARP Programme Support Tool) allows you to adjust settings, conduct performance checks, and upgrade the firmware.
  • Page 10 GX17 CONFIDENTIAL 2. The Input password dialogue box appears. Enter the password, select “USB” from Port list box (a connected port is automatically detected), and click “OK”. When using SPST for the first time, the driver installation starts and the following dialogue box appears. After the installation is complete, press "Retry".
  • Page 11 GX17 CONFIDENTIAL 6. When the password is correct, a connection is established and the following screen appears. First shipped Refer to the attachment 1 software version: for the destination and A49-011-0085-GX17 operator name. [CAW, CBW, CEW, CFW, CLW, CTW, CZW, PEW] A48-011-0086-GX17 [CDW] A50-011-0090-GX17M...
  • Page 12 GX17 CONFIDENTIAL 3. Adjustments for GX17 1. Adjustments are required after replacing the following parts. ( Parts Temperature adjustment Temperature adjustment Display flicker (Camera) (Battery) adjustment TH102 Display unit Camera unit When replacing other parts in the RF section, carry out RF calibration. 2.
  • Page 13 GX17 CONFIDENTIAL 4. Functions 4.1. Default setting SPST can restore the factory settings. This function 1. Deletes all user data in the file system; 2. Restores all WAP settings to default; and 3. Restores the values set by the user to default. (MEPLOCK settings, the destination and operator name do not change.) <Operation>...
  • Page 14: User Data Back-Up

    GX17 CONFIDENTIAL 4.2. User data back-up SPST saves all the data stored on the handset (phone). 1. Set the COM port on the SPST initial screen and click “User Data Backup”. 2. The following message box appears. Check the message and click “Yes”. Click “No” to exit. 3.
  • Page 15 GX17 CONFIDENTIAL 4.3. User data restore SPST completely restores the backed up data. 1. Set the COM port on the SPST initial screen and click “User Data Restore”. 2. The following message box appears. Check the message and click “Yes”. Click “No” to exit. 3.
  • Page 16: Required Devices

    GX17 CONFIDENTIAL 4.4. Downloader 4.4.1 Introduction Downloader allows you to upgrade the firmware. 1) Required devices • PC (Operating System: Windows 2000, XP) • GX17 handset (phone) • USB hub You can use a USB hub to download data to multiple handsets (phones) at a time. Connect a USB Hub when a PC is off.
  • Page 17: Installation Of The Device Driver

    4.4.2 Installation of the device driver After completing the installation of the GX17 Upgrading Tool, install the device driver (SHARP The Upgrading Tool USB Driver Ver 0.90.0) on your 1. Connect a PC and GX17 handset (phone) with the USB download cable.
  • Page 18 GX17 CONFIDENTIAL Press "Continue Anyway" button. Screen during installation. Press "Finish" button. Screen after installation * Install the device driver for each handset (phone) connected to a PC. For example, if five handsets (phones) are connected to PC using a USB hub, the install wizard of the device driver will appear five times. Install the device driver each time, following the instruction.
  • Page 19 GX17 CONFIDENTIAL 4.4.3 Download This section describes how to initialise user data and write data to the handset (phone). 1) Application startup and screen descriptions The icon below is created on your desktop after installation. Double-click it to start the Upgrading tool. You can also start the application by selecting “The GX17 UpgradingTool”...
  • Page 20 GX17 CONFIDENTIAL 2) Download << Easy steps for download>> 1. Connecting the handset (phone) that you download to. Remove the handset (phone) battery and connect the handset (phone) and PC with the USB download cable. When the handset (phone) is recognised as a device on PC, the corresponding Port No. box is checked. (Check of the port cannot be disabled unless the handset (phone) is disconnected from PC.
  • Page 21 GX17 CONFIDENTIAL 2). 2 Selecting MOT file. Select an MOT file to download. Make sure to choose an MOT file for GX17. 1. Press “Select File” button in “2. Select Load File”. The file selection screen appears. 2. Select a file to download and press “Open” button. 3.
  • Page 22 GX17 CONFIDENTIAL 2). 4 Starting download Press “Start the selected operation.” button to start download. [The following shows a single handset (phone) connected to PC via USB download cable.] • If PC and a handset (phone) are not connected, “Start the selected operation.” button stays disabled. Connect your handset (phone) and PC with the USB download cable.
  • Page 23 GX17 CONFIDENTIAL Download progress is shown on the PC and handset (phone). The following shows the process when two handsets (phones) are connected to a PC via a USB hub. Flash Loader V 9.80 Port No.01 Now loading Display on handset (phone) Display on PC Screen during download <<...
  • Page 24 GX17 CONFIDENTIAL 2). 5 Completing download Press “OK” button. When download is successfully completed, “O” appears as shown below. In the screen shot, downloaded data are written to the handset (phone) correctly. Flash Loader V 9.80 Port No.01 Received SUM value SUM = 0xcab5 Display on handset (phone) Display on PC...
  • Page 25 5. Connect the USB download cables to handsets (phones). 6. Install the device driver (SHARP The Upgrading Tool USB Driver Ver 0.90.0) (If using Windows 2000, this will be automatically installed.). For the detail information about how to install the device driver in each OS, please refer to the section “4.4.2 Installation of the device driver” on page 2-9.
  • Page 26: Errors And Troubleshooting

    GX17 CONFIDENTIAL 3). 1 Using multiple USB hubs Connect multiple USB hubs according to the following. 1. Connection in series (recommended) 2. Connection in parallel * When using more than one USB hub, refer to the manuals to interconnect them. 4.4.4 Errors and troubleshooting This section describes error messages, solutions, and other important information.
  • Page 27: Error Message List

    GX17 CONFIDENTIAL Flash Loader V 9.80 Port No.01 Incompatible phone or MOT! = 0x31 Display on handset (phone) Display on PC 1) Error message list Displayed message Cause/Solution Unable to open file Failed to open the MOT file to download. The following are possible causes: - The file path contains special characters.
  • Page 28 GX17 CONFIDENTIAL 4.5. RF calibration & check RF cable Stabilised power supply Handset GSM tester (phone) Test battery GPIB cable Data cable 4.5.1 Preparation • Connect PC and GSM tester with a GPIB cable. • Connect PC and handset (phone) with a data cable. (Use a test battery or similar.) •...
  • Page 29 GX17 CONFIDENTIAL 4.5.2 Default setting for the programme. • Activate the programme and set defaults. 1) A connected COM port appears. 2) Set the GPIB No. 3) Select the test instrument. 4) Set the GPIB address. 5) Set the "Cable Offset" values. For cables with connector QCNWK0138AFZZ/ QCNWKA007AFZZ, set the...
  • Page 30 GX17 CONFIDENTIAL 4. Make sure the voltage is set properly and press “OK”. (Calibration starts.) 5. Click “OK”. 6. The initial screen returns. 4.5.4 RF performance check 1. Apply 4 V using a stabilised power supply and turn on the handset (phone). 2.
  • Page 31 GX17 CONFIDENTIAL 6. Make sure the voltage is set properly and press “OK”. 7. RF performance check is complete. Click “Save As...” and name the file to save the result. Click “OK” to exit. The following will be displayed in case of failure. See the attachment 2 for troubleshooting.
  • Page 32 GX17 CONFIDENTIAL 8. Click “OK”. 9. The initial screen returns. Note: The RF calibration tool allows the calibration but not the check when the terminal fails to catch signals from the GSM tester (unable to access a net- work with “no service” displayed). There is a possibility that CMU200 did not start properly. Turn off CMU200 and restart. 4.5.5 RF calibration &...
  • Page 33 GX17 CONFIDENTIAL Attachment 2 Band Send- Item to be inspected Chan- ing/ Whole inspection list by RF performance check. Recei Band Send- Item to be inspected Chan- ing/ Mod_spectrum +200 37CH PCL19 Recei Mod_spectrum +250 37CH PCL19 Mod_spectrum +400 37CH PCL19 Burst Power 37CH...
  • Page 34 GX17 CONFIDENTIAL Band Send- Item to be inspected Chan- Band Send- Item to be inspected Chan- ing/ ing/ Recei Recei Frequency Error 885CH PCL0 Switch_Spectrum +600 699CH PCL0 Phase Error (RMS) 699CH PCL0 Switch_Spectrum +1200 699CH PCL0 Phase Error (RMS) 512CH PCL0 Switch_Spectrum +1800...
  • Page 35 GX17 CONFIDENTIAL Band Send- Item to be inspected Chan- Band Send- Item to be inspected Chan- ing/ ing/ Recei Recei Mod_spectrum –250 661CH PCL0 Switch_Spectrum –400 661CH PCL0 Mod_spectrum –200 661CH PCL0 Switch_Spectrum +400 661CH PCL0 Mod_spectrum +200 661CH PCL0 Switch_Spectrum +600 661CH PCL0...
  • Page 36 GX17 CONFIDENTIAL 4.6. RF test tool 4.6.1 Requirements For repairs, this test checks the condition of an electric board (especially the RF section). • PC with USB port • GX17 data cable • PWB repair jig • GSM tester (CMU200) 4.6.2 Setup 1.
  • Page 37 GX17 CONFIDENTIAL GSM tester Black (CMU 200) PWB repair jig Data cable Connections Points Contact points 2 – 29...
  • Page 38 GX17 CONFIDENTIAL 3. Apply 4 V using a stabilised power supply and turn on the handset (phone). Push Turning power on 4. Start RF test tool. 5. Press the “Initialize & Read Data” button. (COM port is automatically selected.) 6. Change the voltage, if you need. 7.
  • Page 39 GX17 CONFIDENTIAL 4.6.3 Tests 1) BAND Select & Channel Select a band and a channel to test. Settings are applied to all tests. Input box Band selection Channel bar [Procedure] 1. Select a band. (GSM, DCS or PCS) 2. Select or enter a channel using channel bar or input box. 2) TX test Test burst transmission.
  • Page 40 GX17 CONFIDENTIAL GX17 TX power Table (25°C, voltage: 3.7[V]) GSM Band DCS/PCS Band Tolerance DCS/PCS Tolerance [dBm] [dBm] +/–2 dB +/–2 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB +/–3 dB...
  • Page 41 GX17 CONFIDENTIAL 4) RSSI Measure The handset (phone) notifies you of input power value at the aerial connector. Measured Power box Estimated Power input box (Integer only) Measure button [Procedure] 1. Connect the handset (phone) and GSM tester (or Signal Generator) with RF cable. 2.
  • Page 42: Password Reset

    GX17 CONFIDENTIAL 4.7. Password reset SPST resets the password [handset (phone) code is set to “0000”]. <Operation> 1) Set the COM port on the SPST initial screen and click “User Password Reset”. Click “Yes” to reset. Click “No” to exit. 2) When completed, the following appears.
  • Page 43: Performance Check And Adjustment

    GX17 CONFIDENTIAL 4.8. Performance check and adjustment With this function, SPST checks the performance of the handset (phone) and makes adjustments. <Operation> 1) Set the COM port on the SPST initial screen and click “Performance check and adjustment”. The following dialogue box appears whilst process- ing.
  • Page 44 GX17 CONFIDENTIAL 4.8.1 Back light check The display back light turns on and the message appears on the PC. Check the back light and press “OK”. • If a failure occurs, see “9. Back Light does not turn on.” in [3] Troubleshooting. 4.8.2 Key back light check The keypad back light turns on and the message appears on the PC.
  • Page 45: Audio Test

    GX17 CONFIDENTIAL 4.8.6 Audio test The following appears. Select a test item from Audio device. Check the output sound from the receiver by speaking to the microphone, etc. Click “Back to test menu” to return to the previous screen. Troubleshooting (based on [3] Troubleshooting) Trouble found by SPST (1) &...
  • Page 46 GX17 CONFIDENTIAL 4.8.8 Memory check Click “S-RAM” and “PSRAM” to see each test result. For “Check Sum”, the calculation appears after the SPST communicating dialogue box. 4.8.9 LCD test Check that the specified colour appears on the main display. • If a failure occurs, see “10.
  • Page 47: Other Tests

    Connect GX17 and a PC with a USB cable. Check that GX17 is recognised as a device. If the USB driver for GX17 (SHARP GSM GPRS USB Driver) is not installed on the PC, “Found New Hardware” window appears and “Found New Hardware Wizard”...
  • Page 48: Test Points

    GX17 CONFIDENTIAL [2] Test points TP No. Signal name TP801 VTCXO (2.9V) MAIN PWB-A ( FRONT SIDE ) TP802 VRF (2.9V) TP801 TP802 TP103 TP197 TP122 TP193 TP148 TP117 TP147 TP106 TP115 TP135 TP196 TP140 TP141 TP182 TP155 TP104 TP157 TP130 TP105 TP107...
  • Page 49 GX17 CONFIDENTIAL TP No. Signal name MAIN PWB-A ( REAR SIDE ) TP110 VEXT TP111 VVIB TP112 DGND TP113 VVIB TP119 MIC_INP TP402 TP120 AIN2P_C TP403 TP121 RECEIVER_OUT TP129 USC [6] TP145 TP142 TP142 SPEAKER/RECIVER1 TP144 SPEAKER/RECIVER2 TP146 TP144 TP401 TP145 SPEAKER/RECIVER1 TP146...
  • Page 50: Troubleshooting

    GX17 CONFIDENTIAL [3] Troubleshooting 1. Power dose not turn on. Connect a battery of 4.0 V or more. Execute File System initialisation of Downloader in SPST Flash memory (IC104) and IC106 are defective. without loading a file. Does File System initialisation start properly? Is the user area (file system) initialised by Flash Loader? Does normal mode start? Flash memory (IC104) data is...
  • Page 51: Voice Transmission/Recording Is Impossible

    GX17 CONFIDENTIAL 2. Voice transmission/recording is impossible. Phone (Handset) Replace the microphone. The built-in microphone is defective or in a poor contact with the Is the problem solved? PWB. L101, and C101 are defective. Is 1.2 - 2.1 V applied to both ends of C101? Is 1.2 - 2.1 V applied to TP119? Is 2.4 - 2.6 V applied to TP176? R125 is defective.
  • Page 52 GX17 CONFIDENTIAL Hands free kit (Headset) Replace the hands free kit. Hands free kit is defective. Is the signal sent? Parts between JK101 pin 3 andTP120 are defective. Is 0.7 - 1.8 V applied to JK101 pin 3? Is 0.7 - 1.8 V applied to TP120? Is 2.4 - 2.6 V applied to TP176? R122 is defective.
  • Page 53: No Voice Is Heard From The Earpiece

    GX17 CONFIDENTIAL 3. No voice is heard from the earpiece. Phone (Handset) Do keypad tones and melodies sound? Go to the section “Earpiece (for loud speaker) does not work”. (see page 2-48) Is 0.5 V or more applied to R101 (IC103 pin 9 side)? (Talking) IC103 is defective.
  • Page 54: Battery Does Not Charge

    GX17 CONFIDENTIAL 4. Battery does not charge. Set a battery of 4.0 - 4.2 V. Click the “Performance check adjustment” button on SPST. * For settings and connections for SPST, refer to the “ADJUSTMENTS, PERFORMANCE CHECK, AND FIRMWARE UPGRADE” on page 2-1. Click the “Temperature adjustment”...
  • Page 55: Vibrator Does Not Work

    GX17 CONFIDENTIAL 5. Vibrator does not work. Are vibrator terminals in contact with the land? Vibrator is deformed and defective. (When vibrator terminals Are terminals and the land clean? and the land are dirty, clean or replace them.) Hereafter check with vibrator working. Is rectangular wave of 3 V sent to between vibrator terminals Vibrator is defective.
  • Page 56: Earpiece (For Loud Speaker) Does Not Work

    GX17 CONFIDENTIAL 7. Earpiece (for loud speaker) does not work. * When ring tones sound, but keypad tones do not, “Keypad Tones” is set to Off. * When only ring tones do not sound, “Ringer Volume” is set to “Silent”. * Ring tones sound according to “Ringer Volume”...
  • Page 57: Video/Voice Recorder Playback Is Impossible

    GX17 CONFIDENTIAL 8. Video/Voice Recorder playback is impossible. Earpiece Are keypad tones and ring tones normal? Go to the section “Earpiece (for loud speaker) does not work.” (see page 2-48) In Playback window, does playback start normally and the IC104 or IC106 is defective. capacity bar change? Not defective.
  • Page 58: Back Light Does Not Turn On

    GX17 CONFIDENTIAL 9. Back Light does not turn on. Is VBAT voltage applied to C522? Is C522 in good appearance and mounted properly? C522 is defective or mounted improperly. IC520 is defective or mounted improperly. Is back light setting for Display set to On? Go to the setting as follows and set it to On: Settings →...
  • Page 59: Out Of Range And Incoming/Outgoing Calls Are Impossible

    GX17 CONFIDENTIAL 10. Out of range and incoming/outgoing calls are impossible. [Checkpoints in RF Test Tool] Is transmission possible using RF Test Tool? Go to the section “10.2. Reception system”. Go to the section “10.1. Transmission system”. 10.1. Transmission system Is frequency signal sent to IC803? Main PWB-A is defective.
  • Page 60: The Display Does Not Appear On Display

    GX17 CONFIDENTIAL 11. The display does not appear on Display. Is Display unit fully inserted to CN102? Improperly inserted to the connector. Clean the contact point of CN102 and insert the unit again. The contact point of the connector is dirty. Does the display appear? Replace Display.
  • Page 61: Pictures Cannot Be Taken

    GX17 CONFIDENTIAL 12. Pictures cannot be taken. Is the camera (CAM100) installed in the right direction? Reinsert the camera (CAM100). Check that IC603 has not come off. IC603 is mounted improperly. Is there conduction between TP604 and TP606? Are all the pins of SO601 mounted properly? SO601 is mounted improperly.
  • Page 62: Sim Card Is Not Recognised

    GX17 CONFIDENTIAL (From page 2-53) SO601: R611, R612, and R613 are mounted improperly. Are voltages of the following pins within the range 0 to 2.8 V (when camera is on)? 1. pins 8 - 14 2. pins 17 - 20 IC603 is defective.
  • Page 63 GX17 CONFIDENTIAL 14. IrDA (Infrared) communication is impossible. Set the distance and angle within the specification for the IrDA communication. Short terminal (IC103 pin 4 to TP110) or C164 is defective. Is 2.8 V applied to UN101 pin 6? Are short terminal (IC103 pin 4 to TP110) and C164 good in appearance and mounted properly? IC103 is defective.
  • Page 64: Bluetooth Communication Is Impossible

    GX17 CONFIDENTIAL 15. Bluetooth communication is impossible. A connection cannot be established via Bluetooth. Is 3 V supplied from IC403 pin 3? IC403 or C402, C409 is defective. Is IC402 pin 34 (RESET signal) always at “H”? Parts (between IC106 pin 100 and IC401 pin 34) are defec- tive.
  • Page 65: Usb Connection Is Impossible

    GX17 CONFIDENTIAL 16. USB connection is impossible. Connect a properly working phone to the PC/USB cable that is Reinstall the driver and replace the USB cable to connect the not recognised. Is it recognised? phone. Connect to a PC with the USB cable. Is 5 V or more applied to TP515? CN502 is connected improperly.
  • Page 66 GX17 CONFIDENTIAL – MEMO – 2 – 58...
  • Page 67: Servicing Concerns

    GX17 CONFIDENTIAL GX17 Service Manual   CHAPTER 3. DISASSEMBLY AND REASSEMBLY [1] Servicing Concerns • FASTENING TORQUE (Referential Value) • Back Cabinet / 16.66 ± 1 N • cm 1. For disassembling (1.7 ± 0.1 Kgf • cm) Front Cabinet • Key PWB / 14.7 ±...
  • Page 68 GX17 CONFIDENTIAL Spacer, Display Standard position Press down to attach. Front Cabinet Assembly [Spacer, Display] Back Cabinet Assembly Standard Sensor, position Moisture (Small) Standard position [Sensor, Moisture (Small)] Sheet B, Display FPC Standard position Standard position Standard position Main PWB-A [Sheet B, Display FPC] 3 –...
  • Page 69: Front Cabinet Assembly

    GX17 CONFIDENTIAL [2] Disassembly and reassembly 2. Back Cabinet Assembly • To reassemble, reverse the procedure. Step Part name Q’ty Open the Handsfree Kit Connector Cover. 1. Front Cabinet Assembly Screw (1.7 x 7), Silver (B1) Step Part name Q’ty Battery Cover (A1) Back Cabinet...
  • Page 70 GX17 CONFIDENTIAL 3. Key PWB-B/Display/Display Holder Assembly 4. Main PWB-A Step Part name Q’ty Step Part name Q’ty Hook (C1) Hook (D1) Flat Cable (C2) Flat Cable (C3) Hook (C4) Main PWB-A Main PWB-A Sheet (D1) x 2 Key PWB Holder (C3) x 1 (C4) x 4 (C1) x 1...
  • Page 71: Chapter 4. Diagrams

    GX17 CONFIDENTIAL Service Manual GX17   CHAPTER 4. DIAGRAMS [1] Block diagram (Main) [MAIN] CLKREQOUT BUILT-IN BTCLK AERIAL RF I/F GPIO_3(RTS), GPIO_4(CTS), GPIO_33(RXD), GPIO_34(TXD) IC402 AN401 GPIO_14(PCM_CLK), GPIO_15(PCM_DATAIN) BC313143 GPO_1 (TXON), GPO_18 (SYNTHEN) IC112 GPIO_16(PCM_SYNC), GPIO_17(PCM_DATAOUT) AERIAL GPO_9 (BS3), GPO_11(BS4) GPO_20 (SYNTHDATA) BLUETOOTH MODULE VBAT IC103...
  • Page 72: Block Diagram (Rf)

    GX17 CONFIDENTIAL [2] Block diagram (RF) [RF] RX Line TX Line Control Line BS1 (D) (D): Digital, (A): Analogue BS2 (D) BS3 (D) BS4 (D) PA (A) VBAT (BATT) TP802 TXVCO VOLTAGE Loop GSM900 880.2 to 914.8 MHz VBAT TP801 TCXOEN (D) REGULATOR DCS1800 1710.2 to 1784.8 MHz...
  • Page 73: Block Diagram (Power Supply)

    GX17 CONFIDENTIAL [3] Block diagram (Power supply) [Power Supply] Flash-ReWrite USB_VBUS 4.0V/100mA IC503 IC103 XC621340 (VLOAD) AD6537B CN502 POWER SUPPLY ANALOGUE BASEBAND EXTERNAL VBATSENSE ON/OFF CONNECTOR ISENSE CONTROL (1/2) SIREAL PORT 0.18ohms Charge Timer GATEDRIVE VCHG 4.5V 60mA Trickle Charge AINxP VBAT VMIC...
  • Page 74: Chapter 5. Schematic Diagram And Wiring Side Of P.w.board

    GX17 CONFIDENTIAL Service Manual GX17   CHAPTER 5. [3] Waveforms of circuit SCHEMATIC DIAGRAM AND WIRING SIDE OF P.W.BOARD [1] Notes on schematic diagram RF Test Tool RF Test Tool Tx test Rx test • Resistor: GSM900 Band PCS1900 Band Letters K and M are prefixed to ohm (unit of resistance). K means 1000 ohms and M means 1000 kohms.
  • Page 75: Schematic Diagram (Main 1/5)

    GX17 CONFIDENTIAL [4] Schematic diagram (Main 1/5) 13M-IN (CLKIN) C833 Note: Wallpaper must be on the display. (IC106 142 pin) MAIN PWB-A (1/5) RECEPTION SIGNAL TRANSMISSION SIGNAL TP401 IC403 R118030B VBAT VCORE REGULATOR C401 1/6.3V VOUT C402 1/6.3V C409 0.01/16V 13M-OUT (CLKOUT) IC106 84 pin Note: Wallpaper must be on the display.
  • Page 76: Schematic Diagram (Main 2/5)

    GX17 CONFIDENTIAL [5] Schematic diagram (Main 2/5) MAIN PWB-A (2/5) RECEPTION SIGNAL 2.93V 2.93V UN101 TRANSMISSION SIGNAL VEXT VEXT 2.93V INFRARED PORT VEXT SGND C167 LEDA 4 . 7 / 6 . 3 V C196 0.1/16V C168 0.1/10V C169 0.1/10V C197 SPOUT1 VREF...
  • Page 77: Schematic Diagram (Main 3/5 / Main 4/5)

    GX17 CONFIDENTIAL [6] Schematic diagram (Main 3/5 / Main 4/5) MAIN PWB-A (3/5) MAIN PWB-A (4/5) SW501 SW502 S i d e S i d e UP-key DOWN-key DISPLAY Backlight TP529 LED520 EW008BT1 B a t t e r y 2.8V WHITE VBAT...
  • Page 78: Schematic Diagram (Main 5/5)

    GX17 CONFIDENTIAL [7] Schematic diagram (Main 5/5) MAIN PWB-A (5/5) RECEPTION SIGNAL TRANSMISSION SIGNAL 5-3 (1-E) L823 FERRITE BEADS BATT BATT 5-4 (2-D) IC804 R5322P VOLTAGE REGULATOR TCXOEN VOUT1 5-3 (1-D) C801 VOUT2 1/6.3V TXOUT_DCS/PCS PowerAmp VBAT DCS/PCSIN 5-4 (2-D) C1862 1000p/25V C1863...
  • Page 79: Wiring Side Of P.w.board (Main)

    GX17 CONFIDENTIAL [8] Wiring side of P.W.Board (Main) MAIN PWB-A (FRONT SIDE) MAIN PWB-A (REAR SIDE) UN101 INFRARED PORT ANT801 AERIAL TERMINAL EP100 AN401 EARPIECE AERIAL L833 TERMINAL TP402 C886 TP403 C883 FL401 C413 L831 TP145 TP142 IC402 TP401 TP146 TP144 C402 C410...
  • Page 80: Schematic Diagram/Wiring Side Of P.w.board (Key)

    GX17 CONFIDENTIAL [9] Schematic diagram/Wiring side of P.W.Board (Key) KEY PWB-B (FRONT SIDE) KEY PWB-B LEFT RIGHT SOFT SOFT CENTRE END/ SEND POWER R701 R702 CN701 (GND) KEY PAD KEYPADCOL[2] KEYPADCOL[0] KEYPADROW[4] KEYPADROW[1] KEYPADCOL[1] KEYPADROW[0] KEYPADCOL[3] KEYPADROW[2] KEYPADCOL[4] KEY PWB-B (REAR SIDE) KEYPADROW[3] POWONKEY KEYLED2...
  • Page 81: Voltage Value

    GX17 CONFIDENTIAL [10] Voltage value Conditions: SIM card inserted, power on (3.7V battery), in stand-by mode (No information on the display; with the backlight turned off) Measuring instrument: Digital multimeter : Unmeasurable IC101 IC108 IC503 IC602 IC804 PIN NO. VOLTAGE PIN NO.
  • Page 82 GX17 CONFIDENTIAL – MEMO – 5 – 9...
  • Page 83: Chapter 6. Others

    GX17 CONFIDENTIAL GX17 Service Manual   CHAPTER 6. OTHERS [1] Function table of IC/Camera/Display IC101 VHIYMU762C+-1L: SOUND, YMU762C Pin No. Terminal name Input/Output Description of terminal CLKI Input Clock input terminal LED (NC) Output External LED control terminal (Not used) /IRQ Output Interrupt output terminal /RST...
  • Page 84: Current Limit

    GX17 CONFIDENTIAL IC102 VHIQ5RW45BF-1L: 4.5V REGULATOR, Q5RW45B Pin No. Terminal name Input/Output Description of terminal – Earth – Power supply VOUT Output Output Input Chip enable VOUT VREF CURRENT LIMIT IC103 VHIAD6537B+-1Q: ANALOGUE BASEBAND, AD6537B Pin No. Terminal name Input/Output Description of terminal Input Not used...
  • Page 85 GX17 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal VVCXO Output Voltage controlled crystal oscillator supply 2.71 - 2.79 V (VT) ASDI Input Audio serial port data input BSDO Output Baseband serial port data output NC_E15 – Not used NC_E16 –...
  • Page 86 GX17 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal SGND – AOUT2P/N supply earth AOUT2N Output Speaker with receiver positive output SPWR Input AOUT2P/N supply regulator input AOUT2P Output Speaker with receiver negative output 108* NC_T12 – Not used KEYOUT Output Power-on key output...
  • Page 87 GX17 CONFIDENTIAL IC104 DROMKW578CF0F: FLASH MEMORY, LRS18641 Pin No. Terminal name Input/Output Description of terminal – Not used – Not used Input Address input (common) Input Address input (common) Input Address input (common) Input Address input (common) Input Address input (common) Input Address input (common) –...
  • Page 88 GX17 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal Input Address input (common) Input Address input (common) Input Address input (common) Input Address input (common) SC-/CE1 Input Chip enable input (Smartcombo RAM) – Not used – Not used F2-/CE –...
  • Page 89 GX17 CONFIDENTIAL IC105 VHITC7SZ08F-1L: AND GATE, TC7SZ08F Pin No. Terminal name Input/Output Description of terminal IN B Input Input IN A Input Input – Earth OUT Y Output Output – Power supply IN B IN A OUT Y IC106 VHIAD6528D+-1Q: DIGITAL BASEBAND, AD6528B Pin No.
  • Page 90 GX17 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal CLKOUT_GATE Input Master clock enable from analogue BB (MCLKEN) GPO_1 Output Analogue baseband transmit section control (TXON) OSCIN Input 32.768 kHz crystal oscillator input MC_CMD Output Not used GPIO_55 Input Boot control 1 –...
  • Page 91 GX17 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal – Earth GPIO_4 Output UART_CTS for Bluetooth module GPIO_2 Output Write protect control for Frash Memory 1 GPIO_3 Input UART_RTS for Bluetooth module DATA[2] Input/Output Processor data bus 2 DATA[0] Input/Output Processor data bus 0 DATA[5]...
  • Page 92 GX17 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal GPIO_46 Output Chip select for sound generator IC DPLUS Input USB D+ SIMCLK Output SIM interface clock output JTAGEN Input JTAG enable VEXT Input System Interface power supply 2.4 - 3.3 V (VINT) 180* GPO_3 Output...
  • Page 93 GX17 CONFIDENTIAL IC108 VHIMM32430A-1L: 3.0V REGULATOR, MM32430A Pin No. Terminal name Input/Output Description of terminal Input ON/OFF-Control PIN Input Voltage input VOUT Output Voltage output – Earth IC109 VHIR11630FB-1L: REGULATOR, R11630FB Pin No. Terminal name Input/Output Description of terminal Input Input –...
  • Page 94 GX17 CONFIDENTIAL IC112 VHITC7SZ32F-1L: LOGIC, TC7SZ32F Pin No. Terminal name Input/Output Description of terminal IN B Input Input IN A Input Input – Earth OUT Y Output Output – Power supply IC402 VHIBC313143-1L: BLUETOOTH MODULE, BC313143 Pin No. Terminal name Input/Output Description of terminal VSS_PIO...
  • Page 95 GX17 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal – Earth connection for internal package shield PIO[5] Input/Output Programmable input/output line (Not used) PIO[7] Input/Output Programmable input/output line (Not used) PIO[6] Input/Output Programmable input/output line (Not used) VSS_VCO – Earth connections for VCO and synthesiser VSS_VCO –...
  • Page 96 GX17 CONFIDENTIAL 82 29 30 28 19 74 63 61 53 54 64 13 14 46 48 47 23 24 39 VSS_USB 73, 84 VDD_USB AIO[0] AIO[1] AIO[2] VDD_PIO VSS_PIO 1, 2 RESET_B RESET VSS_PADS VDD_PADS FLASH_EN TEST_EN VDD_MEM 6, 7, 9, 60, 70, 81 VSS_MEM 10, 15, 17, 20, 71 VSS_CORE...
  • Page 97 GX17 CONFIDENTIAL IC501 VHIXC621332-1L: REGULATOR, XC621332 IC503 VHIXC621340-1L: POWER SUPPLY, XC621340 Pin No. Terminal name Input/Output Description of terminal VOUT Output Output – Earth Input ON/OFF control Input Power input ON/OFF Each circuit Control Current Limit 1 VOUT Voltage Reference 6 –...
  • Page 98 GX17 CONFIDENTIAL IC520 VHISC604AIT-1L: WHITE LED DRIVER, SC604AIMLTRT Pin No. Terminal name Input/Output Description of terminal Input Active high enable CTRL0 Input Output control bit 0 CTRL1 Input Output control bit 1 CTRL2 Input Output control bit 2 ISET Input LED current is set by this pin's signal.
  • Page 99 GX17 CONFIDENTIAL IC601 VHIXC621918-1L: REGULATOR, XC621918 Pin No. Terminal name Input/Output Description of terminal Input Input – Not used VOUT Output Output – Not used – Earth Input ON/OFF Control In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. ON/OFF Each circuit Control...
  • Page 100 GX17 CONFIDENTIAL IC603 RH-IXA020AF03L: CAMERA I/F CONVERSION LSI, LR38876 Pin No. Terminal name Input/Output Description of terminal – – Continuity test terminal (Not used) EXCKI Input System clock input – Earth Input CPU I/F address Input CPU I/F address Input CPU I/F write signal input –...
  • Page 101 GX17 CONFIDENTIAL Pin No. Terminal name Input/Output Description of terminal – Earth VSYNC Input Vertical synchronous signal HVDD1 – External digital power supply 1 (+3.0 V) Input Image I/F input data, bit 6 – – Continuity test terminal (Not used) In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
  • Page 102 GX17 CONFIDENTIAL IC801 VHI15515502-1L: RF, 15515502 Pin No. Terminal name Input/Output Description of terminal VCCLNA Input VCC for LNA transistor and LNA Bias PCSGND – Earth for emitter of LNA transistor (PCS) PCSLNAI Input Positive input for LNA transistor (PCS) PCSLNAIB Input Negative input for LNA transistor (PCS)
  • Page 103 GX17 CONFIDENTIAL IC802 VHIRF3146++-1L: POWER AMP., RF3146 Pin No. Terminal name Input/Output Description of terminal – Not used VCC2 GSM Input Controlled voltage input the GSM driver stage – Not used – Earth – Earth Pout_GSM850/900 Output Output power (GSM850/900) –...
  • Page 104 GX17 CONFIDENTIAL VCC2 VCC2 GSM DCS/PCS PoutDCS Pout_GSM 1800/1900 850/900 Fully Integrated Power Control Circuit IC804 VHIR5322P++-1L: VOLTAGE REGULATOR, R5322P Pin No. Terminal name Input/Output Description of terminal Input Chip enable1 Input Power supply Input Chip enable2 VOUT2 Output VCC for VRF –...
  • Page 105 GX17 CONFIDENTIAL CAM100 RUITKA184AFZZ: CAMERA 1 Pin marking 6 – 23...
  • Page 106 GX17 CONFIDENTIAL LCD100 RLCUBA055AFZZ: DISPLAY Terminal Input/Output Description of terminal name Output Tone amplifier reference output VDDAB Output DC-DC converter output (V5OUT x -1) VDDGL Output DC-DC converter output (VDDAB x 2) – Booster capacitor connection terminal – Booster capacitor connection terminal –...
  • Page 107: Parts Guide

    GX17 CONFIDENTIAL PartsGuide PARTS GUIDE No. S0619TQE17REF (Ver. 1) DIGITAL MOBILE PHONE GX17 MODEL (r) Version INTERNAL SELEC- DESTINATION: INTERNAL SELEC- DESTINATION: MODEL TION COLOUR MODEL TION COLOUR NAME CODE NAME CODE TQE17CAW Australia: Black TQE17CTW Italy: Black TQE17CBW Hungary: Black TQE17CUW Belgium: Black TQE17CDW...
  • Page 108 GX17 CONFIDENTIAL PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [1] INTEGRATED CIRCUITS IC101 VHIYMU762C+-1L Sound,YMU762C IC102 VHIQ5RW45BF-1L 4.5V Regulator,Q5RW45B IC103 VHIAD6537B+-1Q Analogue Baseband,AD6537B IC104 -------- This Parts is Supplied with Cabinet Parts 904 IC105 VHITC7SZ08F-1L And Gate,TC7SZ08F IC106 VHIAD6528D+-1Q Digital Baseband,AD6528B IC108 VHIMM32430A-1L...
  • Page 109 GX17 CONFIDENTIAL PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [5] COILS R178 RCILZ0385AFZZN 120 ohms (100MHz) R204 VPBFMS56J1R0MT 56 nH [6] VARISTORS C102 VHV10080MBB-1N Varistor,Voltage:8V C882 VHVEJZ08005-1N Varistor,Voltage:18V V101 VHV10080MBB-1N Varistor,Voltage:8V V502 VHV10080MBB-1N Varistor,Voltage:8V V503 VHV10080MBB-1N Varistor,Voltage:8V V504 VHV10080MBB-1N Varistor,Voltage:8V V505 VHV10080MBB-1N...
  • Page 110 GX17 CONFIDENTIAL PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [10] CAPACITORS C183 VCKYCZ1EB102KT 1000 pF,25V C184 1 µ F,6.3V VCKYCZ0JB105KT C189 1 µ F,6.3V VCKYCZ0JB105KT C190 VCKYCZ1EB102KT 1000 pF,25V C191 0.1 µ F,10V VCKYCZ1AB104KT C194 0.47 µ F,10V VCKYCY1AB474KT C196 0.1 µ...
  • Page 111 CONFIDENTIAL GX17 PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [10] CAPACITORS C845 0.1 µ F,10V VCKYCZ1AB104KT C850 0.015 µ F,50V RC-CZ3001AFZZN C851 1800 pF,25V VCKYCZ1EB182KT C855 47 pF (CH),25V VCCCCZ1EH470JT C856 22 pF (CH),25V VCCCCZ1EH220JT C857 VCCCCZ1EH220JT 22 pF (CH),25V C860 33 µ...
  • Page 112 GX17 CONFIDENTIAL PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [11] RESISTORS R275 VRS-CZ1JB101JT 100 ohm,1/16W R282 VRS-CZ1JB105JT 1 Mohm,1/16W R411 VRS-CZ1JB2R2JT 2.2 ohms,1/16W R502 VRS-CZ1JB474JT 470 kohms,1/16W R503 VRS-CZ1JB474JT 470 kohms,1/16W R504 VRS-CZ1JB103JT 10 kohm,1/16W R505 VRS-CZ1JB474JT 470 kohms,1/16W R506 VRS-CZ1JB152JT 1.5 kohms,1/16W...
  • Page 113: Exploded Parts

    GX17 CONFIDENTIAL [13] EXPLODED PARTS...
  • Page 114 GX17 CONFIDENTIAL PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [13] EXPLODED PARTS GCOVAA258AFSA Cap,Aerial GCOVDA012AFSA Lens,Camera GCOVHA082AFSA Cover,Handsfree Kit Connector GCOVHA083AFSA Cover,External Connector HBDGZA004AFSA Badge,Speech (Except for CFW,CUW) HBDGZA009AFSA Badge,Speech (CFW,CUW) JKNBZA091AFSA Button,10 key (Except for CSA) JKNBZA091AFSC Button,10 key (CSA,PPA) JKNBZA092AFSA Keys,Side-Up/Side-Down LHLDB1190AFZZL...
  • Page 115 GX17 CONFIDENTIAL [14] ACCESSORIES/PACKING PARTS...
  • Page 116 GX17 CONFIDENTIAL PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [14] ACCESSORIES/PACKING PARTS RADPTA019AF01 AC Charger (CEW,CLW,CNW,PEW) RADPTA020AF01 AC Charger (Except for CAW,CEW,CLW,CNW,CZW,PEW) RADPTA021AF01 AC Charger (CAW,CZW) RUITZA006AFP1 Hands Free Kit (CFW Only) SPAKAA007AFZZ Packing Add. (CUW Only) SPAKAA039AFZZ Packing Add. (PEW Only) SPAKCA001EFSA Packing Case (Except for CFW,CUW,PEW) SPAKCA002EFSA...
  • Page 117 GX17 CONFIDENTIAL - MEMO -...
  • Page 118: All Rights Reserved

    CONFIDENTIAL GX17 COPYRIGHT © 2006 BY SHARP CORPORATION ALL RIGHTS RESERVED. No Part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying , recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

Gx17Tqe17cawTqe17cbwTqe17cdwTqe17cewTqe17cfw ... Show all

Table of Contents