Download
Share
Print this page
Pentair iS4 Spa-Side Remote Control Installation And User Manual
  1. Manuals
  2. Brands
  3. Pentair Manuals
  4. Remote Control
  5. iS4 Spa-Side Remote Control
  6. Installation and user manual
Pentair iS4 Spa-Side Remote Control Installation And User Manual

Pentair iS4 Spa-Side Remote Control Installation And User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
iS4 SPA-SIDE REMOTE CONTROL
FOR USE WITH PENTAIR CONTROL SYSTEMS
INSTALLATION AND
USER'S GUIDE
IMPORTANT SAFET Y INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
iS4 Spa Side Remote Installation and User's Guide

Advertisement

loading
Need help?

Need help?

Do you have a question about the iS4 Spa-Side Remote Control and is the answer not in the manual?

Questions and answers

Related Manuals for Pentair iS4 Spa-Side Remote Control

Summary of Contents for Pentair iS4 Spa-Side Remote Control

  • Page 1 SPA-SIDE REMOTE CONTROL FOR USE WITH PENTAIR CONTROL SYSTEMS INSTALLATION AND USER’S GUIDE IMPORTANT SAFET Y INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS iS4 Spa Side Remote Installation and User’s Guide...

  • Page 2: Table Of Contents

    CUSTOMER SERVICE / TECHNICAL SUPPORT If you have questions about ordering Pentair Aquatic Systems replacement parts, and pool products, please use the following contact information: Customer Service Technical Support (8 AM to 4:30 PM Sanford, North Carolina Eastern and Pacific Times (8 A.M.

  • Page 3: Important Warning And Safety Instructions

    IMPORTANT WARNING AND SAFETY INSTRUCTIONS IMPORTANT NOTICE Attention Installer: This Installation and User’s Guide (“Guide”) contains important information about the installation, operation and safe use of this spa side remote control. This Guide should be given to the owner and/or operator of this equipment. Attention User: This manual contains important information that will help you in operating and maintaining this product.

  • Page 4: Overview

    OVERVIEW iS4 Spa-Side Remote Control The iS4 Spa-Side Control can be used with the Pentair IntelliTouch ® ® EasyTouch Control Systems and the Compool CP series Control Systems ® ® to provide remote switching of four control circuits from the spa location. It is typically used for activating spa circulation and three auxiliary pieces of equipment (such as lights, jet pump, air blower, etc.).

  • Page 5: Is4 Spa-Side Remote Gunite Installation

    NOTE: If the Automation Load Center or Power Center to which the spa-side remote is connected is not located above the spa water level, a junction box should be provided (above water level). iS4 SPA-SIDE REMOTE GUNITE INSTALLATION 1. When plumbing the spa, install a 3 in. to 6 in. length of 1 in. Sch 40 PVC pipe (perpendicular to the spa wall) to provide a receptacle for the spa-side remote.

  • Page 6: Gunite Spa Installation

    GUNITE SPA INSTALLATION 1. When the spa construction is completed, cut back the 1 in. diagonal PVC conduit receptacle flush with the spa wall finish or surface of deck. 2. Run spa-side remote cable through conduit to Control Power/Load Center. Use Figure 2 and the color call-out the on back of remote to wire unit.

  • Page 7: Upgrade For Ss4 Installation

    Spa Wall Mounting Adapter Remote Lock-nut ½ in. PVC Conduit iS4 Mounting Adapter Figure 4. UPGRADE FOR SS4 INSTALLATION ight (after electrical requirements are met) 1. Remove existing SS4 making note of function and button color. 2. Orient iS4 Mounting Adapter to optimize usage by spa occupant per Figure 4.
  • Page 8 Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those third parties.

  • Page 9: Control System

    EASYTOUCH CONTROL SYSTEM ® 8 AND 4 FOR POOL AND SPA USER’S GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS...
  • Page 10 Contents IMPORTANT WARNINGS AND SAFETY INSTRUCTIONS ................iii EasyTouch 8 or 4 System Kit Contents ......................v Accessory Equipment ........................... v Technical Support ............................vi Section 1 - EasyTouch Pool and Spa Control System Overview ............1 Operating EasyTouch ............................ 1 EasyTouch Systems .............................
  • Page 11 Contents (Continued) Settings Menu: IntelliFlo / IntelliPro pump) ....................31 How many IntelliFlo pumps will EasyTouch support? ..................31 Selecting the IntelliFlo PUMP TYPE ......................32 Connecting power to an IntelliFlo pump ......................32 Assigning an IntelliFlo VS 3050 pump address ....................32 IntelliFlo VS and VSF+SVRS Settings ......................

  • Page 12: Important Warnings And Safety Instructions

    INSTALLERS, POOL OPERATORS AND POOL OWNERS MUST READ THESE WARNINGS AND ALL INSTRUC- TIONS BEFORE USING THIS PRODUCT. This Guide provides installation and operation instructions for the product. Consult Pentair Water Pool and Spa, Inc. with any questions regarding this product. This product is intended for use in swimming pool applications only.

  • Page 13: General Installation Information

    IMPORTANT WARNINGS AND SAFETY INSTRUCTIONS General Installation Information 1. All work must be performed by a licensed electrician, and must conform to all national, state, and local codes. 2. Install to provide drainage of compartment for electrical components. 3. If this system is used to control underwater lighting fixtures, a ground-fault interrupter (GFCI) must be provided for these fixtures.

  • Page 14: Accessory Equipment

    ® EasyTouch 8 and 4 Pool and Spa Control System Kit Contents ® The following items are included in the EasyTouch 8 and EasyTouch 4 control system kit which may also include the IntelliChlor cell. • EasyTouch control panel (mounted in the load center) •...

  • Page 15: Technical Support

    ® EasyTouch Control System Accessory Equipment EasyTouch Wireless Control Panel, 4 circuits (P/N 520546) EasyTouch Wireless Control Panel, 8 circuits (P/N 520547) iS4 Four-Function Spa-Side remote, 150 ft. cable (P/N 520094) S10 Ten-Function Spa-Side remote, 150 ft. cable (P/N 520149) SpaCommand 10 Ten-Function Spa-Side remote, 150 ft.

  • Page 16: Section 1 - Easytouch Pool And Spa Control System Overview

    Section 1 EasyTouch Control System Overview ® EasyTouch Pool and Spa Control System Overview Welcome to the EasyTouch Pool and Spa Control system − The next generation in automatic control systems. The EasyTouch 8 or EasyTouch 4 system allows you to automatically control all of your spa and pool daily operations.

  • Page 17: Easytouch System Overview

    ® EasyTouch Control System Overview Connects to SpaCommand EasyTouch QuickTouch II Spa-Side Remote IntelliChem Controller motherboard Wireless Remote (P/N 521176) P/N 521356 (Optional (P/N 521245) (Optional EasyTouch 8 Indoor (Optional Control Panel (P/N 520549) EasyTouch Outdoor Control Panel (Optional) Low Voltage (DC) circuit breakers ntelliChlor (SCG) circuit breaker...

  • Page 18: Easytouch Control Panel

    ® EasyTouch Control System Outdoor Control Panel You can fully automate your pool, spa, and lighting operations from the EasyTouch control system outdoor control panel or from the optional EasyTouch control system indoor control panel and EasyTouch wireless control panel. The EasyTouch control system menu features let you create customized schedules for your pool and spa equipment, heat temperatures, and chlorination settings to switch on and off at a set day and time.
  • Page 19 10 minutes to allow the heater to cool down. Pentair heaters do not require a cool down time. To override the “heater cool-down,” press the Filter Pump button again to switch off the pump.
  • Page 20 Controls and buttons (Continued)  When in normal operating mode, the Valves (V) - (Pool/Spa/Fill (Spillway)/Drain) button: Valves (V) button is in “Pool” mode. In this mode the valves are automatically rotated so that only the pool water is circulated through the system and the filter pump is activated. Pressing this button once enables “Spa”...

  • Page 21: Is4 Spa-Side Remote Controller (Optional)

    SpaCommand Spa-Side Remote The optional 10-button SpaCommand spa-side remote can control ten pool/spa functions from the spa location. The spa temperature can be adjusted from the SpaCommand. The SpaCommand spa-side remote also supports IntelliFlo® pump speed and flow control. The remote is a double- insulated device for use with EasyTouch®, IntelliTouch®...

  • Page 22: Easytouch Indoor And Wireless Control Panel (Optional)

    EasyTouch Indoor Control and Wireless Control Panel (Optional) The EasyTouch Wireless or the Indoor Control Panel allows you to control your pool and spa daily operations from around your pool area or inside your home. Use the “P” (Pool) and “Spa” (Pool) buttons to heat and filter your pool and spa.

  • Page 23: Easytouch Outdoor Control Panel Operating Modes

    EasyTouch Control System Outdoor Control Panel Operating Modes The EasyTouch Control System can run in automatic mode or manual mode. Use the “Mode” button to switch the system from “Auto” mode (normal operating mode) to “Service” for manual operation and service purposes. Before operating EasyTouch, familiarize yourself with the LCD status messages and operating buttons.

  • Page 24: Quick Start Spa And Pool Operations

    Quick Start - Spa and Pool Operations (Shared Equipment) The following describes how to adjust heat temperature for the spa and pool water, schedule a daily run time for the pool/spa filter pump and control lights for shared equipment. Heat your spa or pool First enable the heat source (see “Adjust your spa heat settings”...

  • Page 25: Switch On Lights Manually And Synchronize Light Colors

    Switch on lights manually and synchronize light colors From the Lights screen you can manually switch all lights on or off, and synchronize colored lights. Up to 12 ® lights can be controlled. For more information about setting up lights, including IntelliBrite LED lights and ®...

  • Page 26: Schedule Start And Stop Times For Equipment

    Schedule start and stop times for equipment You can set timers (schedules) to automatically run equipment for pool filtration or turn on or off lights. Any EasyTouch circuit can be set to switch on and off on every or any day of the week. Up to 12 total system programs may be created for all circuits combined.

  • Page 27: Setting The Egg Timer Feature

    Setting the Egg Timer Feature The “Egg Timer” feature lets you manually switch on equipment and program the system to automatically switch off after a specified time. You can set this timer feature for other equipment such as lighting, spa, or spa jets.

  • Page 28: Section 2 - Setting Up The Easytouch System

    Section 2 Setting up EasyTouch Setting up the System for the First Time Use the following steps if you are setting up the EasyTouch system for the first time. Note: The following setup steps assume that the EasyTouch Load Center is installed at the equipment pad and ready for operation.
  • Page 29 8. Configure the heater system options (page 25) Set the type of heat source being used (Heater, Solar, Solar Preferred). Enable heat pump (UltraTemp) for heating/cooling if installed. 9. Configure the iS4, iS10, SpaCommand spa-side remote, QuickTouch wireless remote buttons (page 49) Assign circuits to the iS4, iS10, SpaCommand or QuickTouch remote buttons.

  • Page 30: Easytouch Menus

    EasyTouch Menus (Continued) DATE & TIME 1/2 - (MONTH/DAY/YEAR) - (DAY/HOUR/MINUTES/AM/PM) SETTINGS CLOCK DATE & TIMER 2/2 - DAYLIGHT SAVING: (AUTO/MANUAL) CLOCK ADJUST 00:00 (0 TO 300) - (-300 TO -5) IN 5 SCEOND INCREMENTS (OPTIONAL) INTELLIFLO PUMP #1 - PUMP TYPE [VF, VS, VSF, NONE] - VF: FILTR. CIRCUIT, FLOW (GPM), FILTERING, PRIMING, BACKWASH, VACUUM, STATUS PUMP #2 - PUMP TYPE [VF, VS, VSF, NONE] - VS: SPEEDS (RPM), PRIMING, STATUS - VSF: FLOW/SPEEDS (RPM/GPM), STATUS INTELLICHLOR INTELLICHLOR 1/2 - ENABLE (YES/NO), POOL MODE: 0 - 100 % (50% default) SPA MODE: 0% (2% default)

  • Page 31: Main Screen

    EasyTouch Menus From the EasyTouch control panel menus you can schedule everyday pool/spa, heating, filtration and cleaning. Lights and laminars can also be scheduled to switch on and off at specific times. The “Settings” and “Schedule” menus are typically used most often for daily spa and pool operations. The “Settings” menu is used by the pool installer to setup installed equipment which is connected to each output relay (filter pump, auxiliary relays, heater, valves, lights, etc.).

  • Page 32: Feature Circuits Menu

    Feature Circuits Menu There are eight (8) “Feature Circuits” that can be used to control IntelliFlo pump speeds or valves actuators for a spa spillway. Unlike an auxiliary relay circuit, a “Feature” circuit does not connect directly to a relay. “Feature”...

  • Page 33: Lights Menu

    The Color Swim and Color Set lighting features is selected from the LIGHTS > MODES and (COLORS) ® ® ® ® ® menu. At least two (2) Pentair Water Pool and Spa , IntelliBrite , SAm , SAL , and/or FIBERworks lighting systems are required to use the lighting features.

  • Page 34: Setting Up Lights

    Setting up Lights Pentair Water Pool and The following section describes how to assign a light circuit name and function to control Spa IntelliBrite, SAm and/or SAL, and/or FIBERworks lights. Assign the Light Circuit Name and Function The first step in setting up a light circuit is to assign a name to the relay circuit (example; AUX 3, as “Pool Light”), then assign the name “Pool Light”...

  • Page 35: Setting Up Lights

    The Color Swim feature cycles through white, magenta, blue and green colors. Using IntelliBrite lights, Color Swim emulates the Pentair Water Pool and Spa SAM and SAL Color Swim feature. IntelliBrite Light Color Swim/Color Set: If the light was not previously on, after selecting Color Swim, no illumination will occur for approximately six (6) seconds followed by the selection.

  • Page 36: Modes (Color Set)

    Setting up lights (Continued) Modes (Color Set) The “Color Set” feature allows any combination of up to eight (EasyTouch 8) or four (EasyTouch 4) IntelliBrite lights, and SAm, SAL and or Fiberworks lighting to be preset to specific colors. Fixed light colors are selected and activated from the Colors screen.

  • Page 37: Setting Up Sam, Sal, Pg2000, Color Wheel Lights

    Setting up lights (Continued) Config From the “Config” screen you can setup the IntelliBrite light position, and specify the color of each pool and spa light. Any combination of up to eight (EasyTouch 8) or four (EasyTouch 4) IntelliBrite lights, SAM, SAL and or Fiberworks lights can be preset for specific colors and position when using the “Color Swim”...

  • Page 38: Setting Up Magicstream Laminars

    Setting up MagicStream Laminars ® The MagicStream Laminar provide a clear, turbulence-free stream of water that is lit with a fiber optic cable, or an LED light for a dazzling nighttime effect. The 12 VAC powered LED light can generate a series of multicolored light shows, or can be set to display a continuous, single color.
  • Page 39 Using the MagicStream Laminar Features The MagicStream laminar features are displayed in the MagicStream menu. Each time a MagicStream laminar feature is activated, it resumes with the same features in operation as when last switched off. The MagicStream features are as follows: Toggle Thumper - Pressing this button creates a "wrinkle"...

  • Page 40: Heat Menu

    Heat Menu Use the heat menu settings to specify the set point temperature and select the heat source for the pool and spa water. The water will begin to heat whenever the heater is manually switched on, (by pressing the Valves (V) button (on the Outdoor Control Panel) or the “Pool”...

  • Page 41: Delay Cancel Menu

    The Delay Cancel feature is mainly for use by service technicians when it’s necessary to shut the filter pump off immediately, and know the heater has not been running. Heaters manufactured by Pentair Water Pool and Spa do not require this cool-down period and do not need the delay to be set up.

  • Page 42: Schedules Menu

    Schedules Menu Use the Schedules menu to create programs to schedule start and stop times to automatically run equipment, such as pumps and lights. Any circuit can be programmed to switch on and off at a specific time on every or any specific day of the week.
  • Page 43 Schedules Menu (Continued) Schedule your spa/pool pump to turn on Use the Schedule feature to set the time and day(s) when to switch the filter pump on and rotate the pool or spa valves into the “Spa” or “Pool” position. The heater will automatically heat the spa or pool water up to the set point temperature as set in the “Heat”...

  • Page 44: Using The Once Only Feature

    Using the Once Only feature The “Once Only” feature allows you to program a circuit to switch on at a particular time and day on a onetime basis. A typical use for this feature is to have the spa and heater switch on before you get home from work for one evening.

  • Page 45: Using The Egg Timer (Countdown) Feature

    Using the Egg Timer (countdown) Feature The “Egg Timer” feature allows you switch off a circuit automatically after a specified time. The time period is from one minute to 24 hours or run continuously. The “Egg Timer” (countdown) feature is useful for switching off lighting and spa therapy jets.

  • Page 46: Settings Menu: Clock

    Settings Menu: Clock Use the Clock menu to set the EasyTouch system date and time. The day, time and AM/PM is displayed on the main screen. The system clock settings are used for the EasyTouch system scheduled operations. The EasyTouch system clock will continue to run if power is removed from the EasyTouch system at the load center.

  • Page 47: Selecting The Intelliflo Pump Type

    ® Settings Menu: IntelliFlo (Continued) Connecting power to an IntelliFlo pump The IntelliFlo pump is designed to be permanently connected to its power source. Typically the pump receives power directly from the circuit breaker. No contactor or motor starter is required. The drive controls the starting and stopping of the pump.

  • Page 48: Intelliflo Vs And Vsf+Svrs Settings

    IntelliFlo VS and VSF+SVRS Settings  SELECT PUMP TYPE: Up/Down buttons: Choose VS, VF or VSF+SVRS.  Pump Type Speeds Menu button: Press the MENU button to save selection and return to the selected Priming pump’s menu settings (see VS, VF and VSF pump settings descriptions below). Status ...
  • Page 49 IntelliFlo VS and VSF+SVRS Settings (Continued) INTELLIFLO VS PRIMING SETTING:  Pump Type Speeds Down button: Choose SPEEDS.  Priming Right button: Access the priming settings. Status  Up/Down button: Adjust the priming time from 0 to 5 minutes.  Pump Priming Right button: Move to SPEED (RPM) to change the pump speed.
  • Page 50 IntelliFlo VF 3050 Pump Settings To access the IntelliFlo VF menu settings: Getting There MENU SETTINGS INTELLIFLO PUMP # 1 Up/Down button: Choose Pump #1 (or Pump #2) to access the IntelliFlo VF pump settings. If the VF pump is assigned to Pump #2 circuit, be sure to change the pump to “ADDRESS 2”...
  • Page 51 IntelliFlo VF 3050 Pump Settings (Continued) Priming - Max Prime Time: (1 - 15 minutes) Default 15 min.: Use this parameter to set the time that you want IntelliFlo try and prime before it reports an error. Remember that the IntelliFlo will attain prime every time it starts and goes through this cycle.

  • Page 52: Settings Menu: Intellichlor

    Settings Menu: IntelliChlor While the EasyTouch system is in normal operating mode (“Pool,” “Spa” mode or “Spa Fill (Spillway),” it will control the IntelliChlor chlorine output level. The amount of chlorine introduced into the pool is determined by the amount of salt in the water, water temperature, and the amount of time the pool pump is running in “Pool” mode.

  • Page 53: Settings Menu: Intellichem

    ® Settings Menu: IntelliChem IntelliChem provides the EasyTouch system with continual analysis of your swimming pool water sanitation and pH levels, providing real-time status information to dispense the proper amount of muriatic acid (pH reducer) and chlorine or bromine for the correct sanitization and pH balance. IntelliChem operates with or without a salt chlorine generator to provide a self-replenishing supply of chlorine generated from salt.
  • Page 54 SAT INDEX: The Saturation Index (SI), also called the Langelier Index, is a chemical equation or formula used to diagnose the water balance in the pool. The Saturation Index formula is SI = pH + TF + CF + AF - 12.1. To calculate the Saturation Index, you must first test the pool water for pH, temperature, calcium hardness, and total alkalinity.

  • Page 55: Settings Menu: Heat Pump Com (Ultratemp Heat Pump)

    ® Settings Menu: Heat Pump COM (UltraTemp Heat Pump) Heat Pump Com screen From the Heat Pump Com screen you can view the current UltraTemp® operation status, and set the unit to operate with for heating only, cooling only, or both heating and cooling if the unit is reversible. Connection from UltraTemp is via the COM PORT on the EasyTouch motherboard.

  • Page 56: Settings Menu: Circuit Names

    Settings Menu: Circuit Names Labeling Circuit Buttons in the EasyTouch Load Center EasyTouch is factory configured to display each output circuit by its generic name (e.g. AUX 1, AUX 2, etc.). These generic circuit auxiliary names can be assigned a new names which are more descriptive of the equipment being controlled.

  • Page 57: Easytouch Circuit Names

    EasyTouch Circuit Names AERATOR MALIBU LTS Custom Circuit Names (11 characters maximum) AIR BLOWER MIST AUX 1 MUSIC USERNAME-01 ____________________ AUX 2 NOT USED USERNAME-02 ____________________ AUX 3 OZONATOR AUX 4 PATH LIGHTS USERNAME-03 ____________________ AUX 5 PATIO LTS AUX 6 PERIMETER L USERNAME-04 ____________________...

  • Page 58: Settings Menu: Circuit Functions

    Settings Menu: Circuit Functions Assigning Circuit Functions From the “Circuit Functions” menu you can assign special logic to the cleaner pump, spa spillway, lights and MagicStream laminar circuits. For example, when setting up an automatic pool cleaner pump, you would assign the circuit function “MASTER CLEANER.”...

  • Page 59: Preset Circuit Functions

    Preset Circuit Functions l a i . c i c r i t i u h t i l l a i l i e i t h t i c i t o l l t l i f n i t h t i c i t...

  • Page 60: Settings Menu: Custom Names

    Settings Menu: Custom Names There are nearly 100 circuit names available to choose from. If you cannot find one to fit your application you can create up to 10 custom names. Each name can be up to 11 alphanumeric characters. After a custom name is saved, it is then available for selection in the Schedules, 2-Speed Pump, iS4 and QuickTouch menus.

  • Page 61: Settings Menu: 2-Speed Pump

    Settings Menu: 2-Speed Pump Equipment circuits selected in this menu will automatically switch a two-speed filter pump to high speed when these circuits are on. If a two-speed pump is assigned to solar, a cleaner or a pump, when activated the pump will automatically run for five minutes in high speed then switch to low speed.

  • Page 62: Settings Menu: Delays

    Solar Press the Up/Down button to select which solar screen to view. Press the Right Solar  button to select the setting and the Up/Down button to change a setting or value. Enable: Screen (1/3): ENABLE SOLAR: Is the pool using solar heat? Select Yes or No to Heat Pump: No ...

  • Page 63: Settings Menu: F° / C° (Fahrenheit/Celsius)

    Settings Menu: F° / C° (Fahrenheit/Celsius) The temperature settings for the water, solar and air can be displayed in either Fahrenheit or Celsius. Getting There MENU SETTINGS F˚ / C˚ F˚ / C˚ F° / C° To change the temperature units: Up/Down buttons: Select either Fahrenheit or Celsius.

  • Page 64: Settings Menu: 10 Button Spa-Side Remote Controller

    Settings Menu: 10 Button Spa-Side Remote Controller From this menu you can assigning a specific circuit to any one of the ten buttons of an iS10 and SpaCommand spa-side remote to control different pool/spa functions. The iS10 and SpaCommand has ten assignable circuit buttons;...

  • Page 65: Settings Menu: 10 Button Pump Cntrl

    Settings Menu: 10 Button Pump Cntrl From this menu setting you can specify the IntelliFlo VS, VF and VSF pump speed (RPM, GPM) in step increments, for the assigned iS4, iS10 or SpaCommand button using the “Pump Incrs” or “Pump Decrs” circuit (see page 48 and 49).

  • Page 66: Settings Menu: Quicktouch (Qt4) Wireless Remote

    Settings Menu: QuickTouch (QT4) Wireless Remote The QuickTouch QT4 wireless remote controller provides switching of up to four circuits. For example, you can use the QT4 wireless remote to activate the spa circulation, and for operating three auxiliary pieces of equipment (such as heat enabled, lights, jet pump, heat boost, air blower, waterfall, etc.).

  • Page 67: Settings Menu: Man Heat (Off/On)

    Settings Menu: Man Heat (Off/On) By default manual heat (Man Heat) is set to “On,” which allows your spa to begin to heat whenever it is manually switched on, (by pressing the Valves (V) button and Filter Pump (F) button on the outdoor control panel or the Spa button on the Indoor Control Panel), even if the Heat menu setting is set to “OFF”...

  • Page 68: Settings Menu: Erase Eeprom (Erase System Memory)

    Settings Menu: Erase EEPROM (Erase System Memory) EasyTouch system configuration data is stored and retained in “Flash” memory in an EEPROM located on the control panel motherboard and optional Indoor Control Panel. The EasyTouch user system configuration data can be erased to restore the factory defaults settings. System information automatically downloads from programmed components to non-programmed components in case of accidental memory loss and to ease board replacement.

  • Page 69: Settings Menu: Wireless Addr

    Settings Menu: Wireless Addr Use this feature to assign the EasyTouch wireless control panel a unique communication address to allow the wireless device to operate with the EasyTouch outdoor control panel (see page 66). Wireless Addr Getting There MENU SETTINGS WIRELESS ADDR Press Right arrow button To search and lock on to the EasyTouch wireless control panel: Right button: Press this button to automatically search and lock on to the EasyTouch Address Wireless...

  • Page 70: Spa Side [Off/On]

    Spa Side [Off/On] Enable or disable the iS4 Spa Side remote. This feature is useful for families with young children or when you go on vacation. It allows you to switch off the iS4 Spa Side remote at the control panel so that the remote cannot be used.

  • Page 71: Diagnostics Menu: Self Test

    Diagnostics Menu: Self Test Tests the control panel LCD and buttons. Follow the on-screen prompts to perform the tests. Getting There MENU DIAGNOSTICS SELF TEST Note: If the Indoor Control Panel is connected to the EasyTouch outdoor control panel, select “LINK CLOSED”...

  • Page 72: Diagnostics Menu: Chlorinator

    Diagnostics Menu: Chlorinator Displays the current IntelliChlor chlorination system status. For more information, refer to the IntelliChlor Electronic Chlorine Generator User’s Guide (P/N 520589). Getting There MENU DIAGNOSTICS CHLORINATOR Menu: Press this button to return to the Settings menu options. Press the button Chlorinator ...

  • Page 73: Diagnostics Menu: Air Temp

    Diagnostics Menu: Air Temp Displays the current outside air temperature. Getting There MENU DIAGNOSTICS AIR TEMP Press the Menu button to return to the Settings menu options. Press the button again Air Temperature  to return to the main menu options or press again to return to the main screen. 72°...

  • Page 74: Section 3 - Troubleshooting

    Section 3 Troubleshooting Troubleshooting Use the following troubleshooting information to help resolve problems that may occur when using the EasyTouch system. If by following the recommended actions you are still unable to resolve the problems, please contact Technical Support (see page vi). Frequently Asked Questions (FAQ) How do I setup a two-speed pump? A two-speed pump operates using two relays and one or more circuits.

  • Page 75: Easytouch Error Messages

    EasyTouch Error Messages Error Messages If the system detects that a sensor is not connected to the EasyTouch load center or it is defective, an error message is displayed in the “Diagnostics” menu. The following lists the sensor errors. . y l "...

  • Page 76: Intellichlor Error Messages

    Maximum Programs Exceeded The “Maximum Programs Exceeded” message displays in the “Schedules” menu if you try to create a new program after exceeding the 12 program limit. To create a new program you must first delete an existing program. For information about deleting a program, refer to “Schedule Menu” on page 27. IntelliChlor Error Messages IntelliChlor status and error messages are displayed in the “Chlorinator”...

  • Page 77: System Problem Diagnosis

    System Problem Diagnosis Use the following information to resolve system problems. Problem: The system works in Service Mode, but Indoor Control Panel fails to operate. y f i o i t o i t / l e o l l g i l i t c y f i...
  • Page 78 Problem: The Quick Touch remote will not work, or will not work dependably. g i l e i l y l t e l l c i t . l l i t c y f i l l a i t c g i l i t c...
  • Page 79 Problem: The Quick Touch remote will not work, or will not work dependably (Continued). t i n e t l t t i r i c s t i h t i n i t t t i t i n e t l , e t n i t...

  • Page 80: First Time System Start-Up

    First Time System Start-Up The following information describes a basic system start-up procedure. Before you power up the EasyTouch system at the Load Center first check the following: Check Electronics Check that the following plugs are seated correctly on the EasyTouch Load Center motherboard. For connector locations, refer to the EasyTouch System Wiring Diagram on page 64.

  • Page 81: Setting Up The Easytouch Wireless Control Panel For The First Time

    Setting up the EasyTouch wireless control panel for the first time Setting up the EasyTouch wireless control panel In order for the EasyTouch wireless control panel to communicate with the EasyTouch system outdoor control panel, the first time the wireless device is powered up it must first be assigned a unique communication address.

  • Page 82: Synchronizing Control Panels

    Synchronizing control panels If the EasyTouch outdoor control panel was previously setup with specific pool and spa information and an additional indoor or wireless control panel with factory default information is installed, during the installation process the outdoor control panel will automatically download the system information to the connected control panel.

  • Page 83: Glossary

    Glossary Aux Extra: An additional auxiliary output circuit that uses the Solar socket (J17) on the EasyTouch motherboard. Uses the Solar button on the outdoor control panel to switch circuit on and off. Only available if solar equipment is not being used. COM port: RS-485 communication port for connection to iS10 and SpaCommand spa-side remote controller, UltraTemp heat pump, EasyTouch Indoor Control Panel, IntelliChlor, IntelliChem, IntelliFlo and QuickTouch RF transceiver.
  • Page 84 United States and/ or other countries. Unless expressly noted, names and brands of third parties that may be used in this document are not used to indicate an affiliation or endorsement between the owners of these names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those third parties.