Advertisement
LUMASPORT 16
White LED Sports Luminaire
Installation Manual
ASSEMBLE: EPH-LS-16-1200L Light Head
ONLY WITH PART: EPH-LS-16-1200L Driver Box
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT
BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS
Follow all warnings and cautions outlined here as well as any local safety procedures. Failure to strictly adhere to
the warnings and cautions as well as the installation instructions may result in serious personal injury or property
damage
Before You Begin
Read and understand this entire manual and any additional site-specific installation documents before attempting
to assemble, install, or operate the luminaire. If you have any questions regarding the product or installation,
contact Cooper Lighting Customer Service at 1-800-573-3600.
1.
All electrical work must conform to National Electrical Code (NFPA 70), IEEE Emerald book, and all applicable
local codes and ordinances.
2.
Verify the capacity and integrity of existing power distribution system and correct branch circuit voltage before
beginning installation.
3.
Verify the structural capacity and safety of all facility/venue/pole supports and mounting apparatus before
installation. See fixture specification sheet for weight and wind loading data.
4.
Verify that the capacity and integrity of all existing mounting structures and electrical distribution systems are
compatible with the new lighting system and compliant with all regulatory and safety codes.
5.
In harsh settings where the system is subjected to factors such as extreme temperatures, high corrosion,
hurricanes, or lightning, always follow local codes and additional protocols to ensure the cabling and other
system components can withstand the environmental stress for the life of the system.
6.
DO NOT make or alter any open holes in the luminaire. Do not modify the luminaire, internal wiring, or fixture
mounting features. Opening or modifying the luminaire or bracket will void the warranty.
7 .
Use Personal Protective Equipment including hardhats, safety glasses, reflective vests, electrical safety gloves,
fall protection equipment, and safety toe boots during installation, operation, and maintenance of luminaire.
8.
Verify compliance with local standards to prevent access to the area below where installation activities are
occurring to prevent injury from accidental drops of fixtures, tools or hardware.
Storage
Store luminaires in a clean, dry place, protected from dirt, water, and sunlight prior to installation.
See Table 1 for required storage and operating conditions:
WARNINGS AND CAUTIONS
Classified
1
EEL-UNV-0720
EEL-UNV-0711
EEL-UNV-0711
Advertisement
Table of Contents
Related Manuals for EPHESUS LUMASPORT 16
Summary of Contents for EPHESUS LUMASPORT 16
- Page 1 LUMASPORT 16 White LED Sports Luminaire Installation Manual ASSEMBLE: EPH-LS-16-1200L Light Head ONLY WITH PART: EPH-LS-16-1200L Driver Box THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED CE PRODUIT DOIT ÊTRE INSTALLÉ...
- Page 2 Range (>60% Load) (ms) Cooper Lighting Ephesus LED luminaires are not traditional metal halide lights; they are high-tech, new-generation (VAC) Load) solid-sate devices. To protect your valuable investment, ensure the electrical power supply is clean and stable with no spikes or sags.
- Page 3 Operating Conditions and Clearances Mechanical Clearances - Avoiding Obstructions Refer to the following sections for thermal, optical, and mechanical clearance requirements. In general, fixtures can be moved up to 5ft from the designed location without affecting photometric results as long as they are aimed at the designed aiming coordinates.
-
Page 4: Installation Instructions
Installation Instructions Install power cable Correct Installation Incorrect Installation Always turn all fixture power sources OFF before performing any work on power or control wiring. Failure to disconnect all Step 1 – Prepare the luminaire power sources may lead to damage, injury, or death. Hinge Side Latch Side LumaSport Driver Box and Light Head must have... - Page 5 Step 2 – Install the Driver Box Failure to label the luminaire upon addressing may result in improper installation and system malfunction. Driver Box Orientation Arm Prep Driver Box must be installed on a flat and level surface. Do not install the pendant mount configuration in wet locations. Failure to install Driver Box in approved orientation or location may result in damage, injury, or death.
-
Page 6: Incorrect Installation
Pendant Mount – The Driver Box with pendant mounting bracket must ALWAYS be with the arm quick mount Mounting Hole Dimensions hook facing up. This will cause the lid to open down. Do NOT install Driver Box in any other orientation. The pendant mount configuration is rated for dry or damp location only and must not be used in wet locations. - Page 7 Orient the driver box (Pre-aim Orientation 0-55°) Install the Driver Box To pre-aim the fixture orientation, rotate the Driver Box about the mounting bolt until the parallel reference line that was marked Remove orange mounting hole cover inside Driver Box. Set Driver Box on the mounting structure so that the center on the mounting structure is aligned with the correct angle shown in white on the orient label in the bottom of the Driver Box.
- Page 8 9/16in Socket & Ratchet 3/4in-10 X 6in Structural Hex Bolt, Diving Board is intended to only to mount 120ft·lb. LUMASPORT 16 luminaires only. Do not use in unapproved Hot Dip Galvanized to 2in x 4in steel cross arms. • Adjustable Crescent Wrench luminaires or mounting applications.
- Page 9 DMX IN DMX OUT DB4a Correct Installation Install control cables (Wired DMX Configurations) ote: For wireless applications, skip to Record MAC Address step. Control Standards: All control work must conform to ANSI E1.11 – 2008 (r2013), USITT DMX512-A, Asynchronous Serial Digital Data Transmission Standard for Controlling Lighting Equipment and Accessories.
- Page 10 Spring Plunger Disengaged Spring Plunger Engaged Pendant Mount Spring Plunger Tile Lock Screw Rotate the labeled aiming plate until the arrow is over the desired tilt angle. Hold the aiming plate in place and tighten the tilt lock screw. If laser aiming, tighten the tilt lock screw so that fixture is secure but do not fully torque hardware until final aiming is complete. If using the tilt gage, torque the tilt lock screw to: Hardware Description Use / Location...
- Page 11 Light Red Dark Red PSU 2 DC from second Power Supply (for Lumasport 16 configurations) Tighten All Hardware LIGHTHEAD After the fixture is aimed. Tighten all mounting and aiming hardware on the light head and driver box to the torques specified in the table below.
- Page 12 Make sure no wires are pinched in the cover. Re-lock the bail latches. Tighten the captive driver box cover screws to: After Aiming Hardware Description Use / Location Tool Quantity Torque 1/4in-20 Captive Screw Driver Box Lid Screw 3/16in Allen 75 in lbs Retention Cable Routing Retention Cable Routing...
-
Page 13: Basic Functionality
Basic Functionality When initial AC power is applied, the luminaries may have a fraction of a second delay and appear staggered for banks of lights. The minimum light output on the fixtures is 10%. Therefore, the diming range is 0, 10%-100%. A slight jump in light output may be perceived when dimmed up from blackout. -
Page 14: Troubleshooting
Troubleshooting The LumaSport luminaire is designed to provide many years of reliable quality lighting. If the system appears to not be operating correctly find out as much about the issue as possible by asking the following questions: How many fixtures are not operating correctly? If only one fixture is not responding, continue investigating at that fixture itself.
Need help?
Do you have a question about the LUMASPORT 16 and is the answer not in the manual?
Questions and answers