Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ironton 57933
Summary of Contents for Ironton 57933
- Page 1 14-In. Oscillating Wall-Mount Fan Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item #57933 READ & SAVE THESE INSTRUCTIONS...
- Page 2 Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it.
-
Page 3: Table Of Contents
Table of Contents Intended Use ............................4 Packaging Contents ..........................4 Technical Specification ........................4 Important Safety Information ....................... 4 Specific Operation Warnings ....................... 6 Grounding .............................. 7 Extension Cords ............................ 7 Assembly Instructions .......................... 8 Operating Instructions ........................12 Maintenance ............................ -
Page 4: Intended Use
Intended Use The Ironton 14 Inch Oscillating Wall-Mount Fan can be used for cooling or to circulate air indoors or in a garage setting. When in operation, the fan has to be mounted to a wall. Packaging Contents ... - Page 5 Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust.
-
Page 6: Specific Operation Warnings
Store the product when it is not in use. Store it in a dry, secure place out of the reach of children. Inspect the tool for good working condition prior to storage and before re-use. Use only accessories that are recommended by the manufacturer for use with your product. Accessories that may be suitable for one product may create a risk of injury when used with another tool. -
Page 7: Grounding
Grounding ⚠WARNING This fan must be grounded while in use to protect the operator from electrical shock. This fan is equipped with an electrical cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances. -
Page 8: Assembly Instructions
As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. The smaller the gauge number of the wire, the greater the capacity of the cord. - Page 9 2. Propeller Assembly 2-1. Remove the nut from the motor shaft (Fig.2). 2-2. Slide the propeller onto the motor shaft by aligning its slot with the pin in the shaft (Fig.2). 2-3. Secure the propeller with the nut (Fig.2). Page 9 of 18...
- Page 10 3. Front Grill Assembly 3-1. Remove the screw and nut in the bottom of the front grill (Fig.3). 3-2. Place the front grill against the rear grill with its top buckle encases the rim of the rear grill, and then turn all other buckles so they are encasing the rim also (Fig.3). 3-3.
- Page 11 2. On each horizontal line, drill two holes 4.6 cm apart from the center line with a diameter as that of the wall plugs provided (Fig.5). 3. Insert four wall plugs into the holes (Fig.6). 4. Drive the two provided tapping screws (0.5 cm in diameter and 5 cm length) into two upper wall plugs, leaving a gap of 0.5 cm between the screw head and wall (Fig.
-
Page 12: Operating Instructions
5. Hang unit on the wall. Align its two key holes at the two screws on the wall (Fig.7). 6. Drive the two provided tapping screws (0.5 cm in diameter and 5 cm length) through the lower two holes of the base into the wall plug and secure the unit firmly against the wall. 7. -
Page 13: Maintenance
Do not operate in the presence of explosive and/or flammable fumes. Do not plug/unplug the fan into/from the electrical outlet while wet or standing in a wet or damp area. Never operate the fan without the guard in place. ... -
Page 14: Troubleshooting
and maintenance. Have necessary repairs made by qualified service personnel. • Always disconnect the cord from the electrical outlet before cleaning your fan. • Light accumulated dust may be removed by using a soft cloth to wipe away the dust at the back grill of the fan. -
Page 15: Parts Diagram
Parts Diagram Parts List Part Number Part Description Quantity Screw Front Grill Screw Propeller Flange Screw Rear Grill Screw Front Housing Motor Screw Oscillation Knob Rear Housing Screw Link Sleeve Plastic Bracket Irregular Sleeve Steel Bracket Screw Lock Knob Bolt Curve Tube Base Cover Page 15 of 18... -
Page 16: Replacement Parts
Part Number Part Description Quantity Power Cord Switch Brace Base Screw Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. -
Page 17: Limited Warranty
Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. - Page 18 Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.com Made in China Page 18 of 18...
Need help?
Do you have a question about the 57933 and is the answer not in the manual?
Questions and answers