1. Manuals
  2. Brands
  3. Psion Teklogix Manuals
  4. Rfid Systems
  5. WORKABOUT PRO HDK
  6. User manual

Psion Teklogix WORKABOUT PRO HDK User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Psion Teklogix
WORKABOUT PRO HDK
User Manual
September 12 2007
Part No. 8100057.C
ISO 9001 Certified
Quality Management System

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WORKABOUT PRO HDK and is the answer not in the manual?

Questions and answers

Related Manuals for Psion Teklogix WORKABOUT PRO HDK

Summary of Contents for Psion Teklogix WORKABOUT PRO HDK

  • Page 1 Psion Teklogix WORKABOUT PRO HDK User Manual September 12 2007 Part No. 8100057.C ISO 9001 Certified Quality Management System...
  • Page 2 © Copyright 2007 by Psion Teklogix Inc., Mississauga, Ontario This document and the information it contains is the property of Psion Teklogix Inc., is issued in strict confidence, and is not to be reproduced or copied, in whole or in part, except for the sole purpose of promoting the sale of Psion Teklogix manufactured goods and services.
  • Page 3 Return-To-Factory Warranty Psion Teklogix Inc. provides a return to factory warranty on this product for a period of twelve (12) months in accordance with the Statement of Limited Warranty and Limitation of Liability provided at www.psionteklogix.com/warranty. (If you are not already a member of Teknet and you attempt to view this warranty, you will be asked to register.
  • Page 4 (or on a related accessory such as the charger or docking station) signifies that the product is RoHS-compliant as per the EU directive. Other than as noted below, a Psion Teklogix product that does not have an accompanying RoHS logo signifies that it was placed on the EU market prior to July 1, 2006, and is thereby exempt from the directive.

  • Page 5: Table Of Contents

    Registry Settings For Non-Psion Teklogix Device Drivers ........
  • Page 6 Four Unit Multi-Dock Docking Station (Quad Docker) ......... . . 51 Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 7 Signals To The Scanner Device ................86 Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 8 11.7 Installation ....................119 Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 9 Psion Teklogix WORKABOUT PRO User Manuals ........
  • Page 10 ..................I Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 11 1.6 Discontinued Hardware ......... . 7 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 13: Chapter 1: Introduction

    Chapter 1: Introduction About This Manual About This Manual This manual is supports developers of customized hardware for all variants of the Psion Teklogix Inc. WORKABOUT PRO hand-held computer. Chapter 1: Introduction is an overview of the WORKABOUT PRO Hand-Held Computer and the WORKABOUT PRO HDK.

  • Page 14: Text Conventions

    Sample schematics and drawings for expansion modules and scanner converter boards. 1.3.1 Files In The HDK Table 1.1 Files in the HDK Filename Description ...\Mechanical\WORKABOUTPRO\G2\iges_files Body shell—WORKABOUT PRO 2nd. \G2_C_body.igs Generation—C variant..\Mechanical\WORKABOUTPRO\G2\iges_files Mounting frame—WORKABOUT PRO 2nd. \G2_mounting_frame.igs Generation C, and S variants. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 15 \housing_body.pdf MISSING ...\Mechanical\WORKABOUTPRO\pdf 2D internal frame—WORKABOUT PRO C, M, \internal_metal_frame.pdf and ME variants..\Mechanical\WORKABOUTPR\G2\pdf 2D card stop—WORKABOUT PRO 2nd. \mechanical_stop.pdf ADD TO LIBRARY Generation C, and S variants..\Mechanical\WORKABOUTPRO\pdf 2D stylus—all variants. \stylus_pen.pdf Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 16: Obtaining The Hdk

    Sample schematic scanner interface board for a \USBScannerInterfaceBoard.pdf USB scanner—all variants. Obtaining The HDK The HDK is available as a download from Psion Teklogix. If you have a Teknet usercode, the download is available on the Teknet site at: www.PsionTeklogix.com/downloads About the WORKABOUT PRO Hand-Held Computer The WORKABOUT PRO Hand-Held Computer is an industrial hand-held computer.

  • Page 17: Discontinued Hardware

    The WORKABOUT PRO M and some of the peripherals described in this manual are no longer available for purchase from Psion Teklogix. They are included in this manual for the benefit of de- velopers who are continuing to support them alongside newer hardware. For currently available hardware consult the Accessories Catalog at www.PsionTeklogix.com/Accessories.
  • Page 19 2.10 Connector Locations ......... . 17 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 21: Chapter 2: Hardware

    The scanner connects through a flex cable to the scanner connector on the WORKABOUT PRO main logic board. The scanner may be installed by the end user; for instruc- tions see Psion Teklogix WA9000, WA9005, & WA9006 Scanner Module Installation (Part number 8000030).

  • Page 22: Peripheral Processors

    Audio Jack LIF Connector (18-pin) (headphone, mic) (12-pin) 2.3.2 Peripheral Processors MSP430MF133 Keyboard Processor The WORKABOUT PRO has a keyboard processor, for controlling and monitoring the keyboard and signal LEDs, and the battery. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 23: Workabout Pro 2Nd. Generation C, S

    (e.g. Li-ion battery chargers) in the system. It also detects the presence of devices connected to the LIF port and the tether port. LC4128ZC CPLD This CPLD is used for interfacing Compact Flash and PC cards via the internal 100-pin expansion slot. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 24 Power Path Selector Tether LIF ID SERIAL Input Input Client Host Detect Detect Tether Connector LIF Connector DC Input Jack (18-pin) (12-pin) GoForce 4000 Media Processor This provides the following: • Video controller. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 25: Identifying Hardware

    WORKABOUT PRO can be powered from external power. When the WORKABOUT PRO is powered from external power, the battery pack also charges. Use only power sources recommended or sold by Psion Teklogix for the WORKABOUT PRO. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 26: Chapter 2: Hardware Batteries

    Figure 2.3 WORKABOUT PRO back view showing the positions of the on/off switch WORKABOUT PRO C, M, ME WORKABOUT PRO S variant variants (SW1401) (SW1401) Back- Battery WORKABOUT PRO 2nd. Generation S variant (SW1502) WORKABOUT PRO 2nd. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 27: Connector Locations

    Figure 2.4 Connector Locations On The WORKABOUT PRO C, M, And ME 100-Pin Connector Audio Connector Scanner Connector (Not supported in software) Figure 2.5 Connector Locations On The WORKABOUT PRO S 100-Pin Connector Audio Connector (Not supported in software) Scanner Connector Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 28 Chapter 2: Hardware Connector Locations Figure 2.6 Connector Locations On The WORKABOUT PRO 2nd. Generation C And S USB Connector Audio Connector 100-Pin Connector Audio Connector (Not supported in software) Scanner Connector Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 29 3.3 Non-Psion Teklogix Drivers ........

  • Page 31: Chapter 3: Software

    3.2.1 The Peripheral Control (PCO) Driver Psion Teklogix provides the peripheral control driver (PCO), a driver for the 100-pin expansion slot. The PCO driver is a Streams driver activated very early at boot up time (it is loaded after the File devices driver and the I2C driver).

  • Page 32: System Initialization

    During system startup the following occur: 1. The expansion module EEPROM is initialized and read. 2. If a non-Psion Teklogix device driver is required, it is identified from the EEPROM data and activated. For details of this process see “Loading Non-Psion Teklogix Device Driv- ers”...

  • Page 33: Registry Settings For Psion Teklogix Device Drivers

    HDK API library. 3.5.4 Registry Settings For Non-Psion Teklogix Device Drivers All non-Psion Teklogix device drivers must have a registry entry. These device driver entries are formatted as follows: HKEY_LOCAL_MACHINE\Drivers\PsionTeklogix\Expansion Slot\EEPROM Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 34: Chapter 3: Software Com Port Assignments

    Module EEPROM Fields” on page 75. 3.5.4.1 Loading Non-Psion Teklogix Device Drivers At system startup the following process is used to load non-Psion Teklogix device drivers: 1. The contents of the Manufacturer/Model field in the expansion module EEPROM are appended to the registry key...

  • Page 35: The C++ Application Programming Interface

    The WORKABOUT PRO HDK API library enables application programs to control custom-built hardware that connects to the 100-pin connector and the scanner connector. 3.7.1 Installing The Software The WORKABOUT PRO HDK API library is installed as part of the Psion Teklogix Mobile Devices SDK. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 36: Chapter 3: Software Development Platforms

    Chapter 3: Software Development Platforms 3.7.2 Development Platforms The following development platforms should be used with the WORKABOUT PRO HDK: Windows Development Environment Windows Mobile 2003 Microsoft eMbedded Visual C++ 4.0 compiler. It is recommended that eMbedded Visual C++ 4.0 Service Pack 3 Windows CE .NET 4.2...

  • Page 37: The Usbhub Namespace

    Chapter 3: Software The USBhub Namespace namespace do not override these settings. For details see “Registry Settings For Psion Teklogix Device Drivers” on page 23, and “Expansion Module EEPROM Fields” on page 75. On the WORKABOUT PRO 2nd. Generation, the expansion USB is also available on the connec- tor CN601 on the top of the unit.
  • Page 39 4.4.5 Bottom Footprint........37 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 41: Chapter 4: Mechanical Considerations

    ...\Mechanical\WORKABOUTPRO\pdf \endcap_assembly.pdf 2D ball for endcap ...\Mechanical\WORKABOUTPRO\pdf \endcap_assembly_ball.pdf 2D endcap ball holder ...\Mechanical\WORKABOUTPRO\pdf \endcap_assembly_ball_holder.pdf 2D endcap, and ball spring ...\Mechanical\WORKABOUTPRO\pdf \endcap_assembly_ball_spring.pdf 2D stylus gasket for endcap ...\Mechanical\WORKABOUTPRO\pdf \endcap_assembly_stylus_rubber.pdf 2D stylus pen ...\Mechanical\WORKABOUTPRO\pdf \stylus_pen.pdf Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 42 WORKABOUT PRO 2nd. Generation IGES FIles Description File Name Body shell—WORKABOUT PRO 2nd..\Mechanical\WORKABOUTPRO\G2\iges_files Generation C \G2_C_body.igs Body shell—WORKABOUT PRO 2nd..\Mechanical\WORKABOUTPRO\G2\iges_files Generation S \G2_S_body.igs Mounting frame ...\Mechanical\WORKABOUTPRO\G2\iges_files \G2_mounting_frame.igs Mechanical card stop ...\Mechanical\WORKABOUTPRO\G2\iges_files \mechanical_stop.igs Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 43: Installation

    Several Psion Teklogix scanner modules are mounted on scanner-specific backplates. There are a number of scanner kits available for the WORKABOUT PRO. These include scanner backplates, scanner endcaps, and mounting hardware. For a list of Psion Teklogix scanner kits see the Accessories Catalog at www.PsionTeklogix.com/Accessories.

  • Page 44: Chapter 4: Mechanical Considerations Expansion Module Installation

    The recommended material for endcaps and backplates for the WORKABOUT PRO is GE C1200 plastic (standard black). The recommended texturing is AT-IM002, 0.035mm deep, or MT11030. Both the card stop and the ball holder used in the endcap assembly are also made of this material. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 45: Backplate-Mounted Device

    The centre of the connector on the expansion module must be aligned on the centre line of the mounting frame. The connector is mounted in the following location on all WORKABOUT PRO variants: Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 46: Chapter 4: Mechanical Considerations Endcap, Card Stop, And Stylus

    It is important that the correct card stop is fitted. It must fit into the internal frame and housing with no interference to the endcap. Consult the drawings for information on which card stops are used in each WORKABOUT PRO variant, and which card stops are used with each card type. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 47: Bottom Footprint

    Body of WORKABOUT PRO (M, ME, and C variant) colour_mono_terminal.igs Body of WORKABOUT PRO (S variant) short_terminal.igs Body of WORKABOUT PRO 2nd. Generation G2_S_body.igs (S variant) Body of WORKABOUT PRO 2nd. Generation G2_C_body.igs (C variant) Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 49 5.10 Mechanical Considerations........56 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 51: Chapter 5: External Connectors

    AC adaptors, USB or serial adaptors, and other accessories. The audio connector accepts headphones and microphones. Figure 5.1 WORKABOUT PRO Base Showing External Connectors LIF Connector Tether Connector Audio Connector Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 52: Workabout Pro 2Nd. Generation C, S

    V_BAT Tether Connector Battery Switch Charger 5.2.2 WORKABOUT PRO 2nd. Generation C, S The WORKABOUT PRO 2nd. Generation computers have the following external connectors: • LIF connector • Tether connector. • Power connector. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 53 WORKABOUT PRO 2nd. Generation C, S Figure 5.3 WORKABOUT PRO 2nd. Generation Base Showing External Connectors Tether connector LIF connector DC connector Figure 5.4 External Connectors On The WORKABOUT PRO 2nd. Generation C, S Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 54: The Lif Connector

    Pull-down Resistor Device 100 kΩ, 1/8 W, 5% USB host. The Psion Teklogix Mobile Devices SDK enables a software application to detect and identify the connected device. The Tether Connector 5.4.1 The WORKABOUT PRO C, S, M, ME Tether Connector The tether connector gives access to the following: •...

  • Page 55: Com2: Serial Port

    Important: These serial lines are not at RS-232 specifications. They are connected directly to the WORKABOUT PRO main logic board. They are at CMOS levels, between 3.3 V and ground, and are unbuffered. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 56: Sensing Device Presence

    TETHER_DETECT (pin 7) and ground: Pull-down Resistor Device 100 kΩ USB host. 200 kΩ USB client. 49.9 kΩ USB serial. The Psion Teklogix Mobile Devices SDK enables a software application to detect and identify the connected device. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 57: The Workabout Pro 2Nd. Generation C, S Tether Connector

    Power supply to Power WORKABOUT PRO. input COM2: Input COM2: Output COM2: Input COM2: Output COM2: Input COM2: Input Ground Power Ground Power Abbreviations: N/A= not applicable; B = both high and low, Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 58: Chapter 5: External Connectors Cables For The Tether Connector

    The Psion Teklogix Mobile Devices SDK enables a software application to detect and identify the connected device. 5.4.3 Cables For the Tether Connector Psion Teklogix provides cables that connect to the tether port of the WORKABOUT PRO. For a complete list see www.PsionTeklogix.com/Accessories. These cables include the following: •...

  • Page 59: Docking Stations

    These units also have a spare battery charging well. If no external power is supplied to the docking station, the USB ports are still functional. Figure 5.7 Docking Station Block Diagram Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 60: Chapter 5: External Connectors Single Unit Docking Stations

    The USB client connector on the docking station connects an external device, as a USB client, to the docked WORKABOUT PRO. It uses a USB Type B receptacle. Figure 5.9 USB Client Connector Pin 2 Pin 1 Pin 4 Pin 3 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 61: Four Unit Multi-Dock Docking Station (Quad Docker)

    Each USB-to-ethernet converter has a separate MAC address. All are connected to a common ethernet hub, which is connected to the single external ethernet connector. The ethernet connector is a standard 10BASE-T twisted pair connector. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 62: Vehicle Cradles

    Every cradle has the following connector: • 15-pin vehicle cradle connector. Some cradles are powered from the vehicle battery: others are unpowered. For information on the cradles available for your WORKABOUT PRO see the Accessories Catalog at www.PsionTeklogix.com/Accessories. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 63: The Vehicle Cradle 15-Pin Connector

    Ground. Power Ground. Power USB_H4_D+ USB host port 4 D+. Bidirectional USB_H4_D- USB host port 4 D-. Bidirectional USB_H4_PWR USB host port 4 power. Power DC_IN Power supply to Power input WORKABOUT PRO. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 64: Chapter 5: External Connectors Port Replicator

    50 mA when no peripherals are connected to it. The DC input of the powered cradle is regulated and fed only to the power input of the WORKABOUT PRO. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 65 Inside the port replicator, the USB host signals from the WORKABOUT PRO are connected to a processor that provides the three sets of serial port signals. The USB client lines are connected to the USB client connector. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 66: Chapter 5: External Connectors The Serial Connectors

    5.10 Mechanical Considerations The WORKABOUT PRO HDK provides 3D models of the outsides of the WORKABOUT PRO variants to aid in sizing devices that accept the computer and in locating and aligning the connec- tors within them. The tether connector is intended for free-standing cables. Clearance should be provided around it.

  • Page 67: Chapter 6: Internal Connectors

    6.5 Scanner Connector..........60 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 69: Overview

    WORKABOUT PRO 2nd. Generation C, S Audio Connector All WORKABOUT PRO 2nd. Generation computers have an internal audio connector. This con- nector accepts a 3.5 mm stereo connector. Psion Teklogix supplies a cable that connects to this socket. For information see the Accessories Catalog at www.PsionTeklogix.com/Accessories.

  • Page 70: Internal Connectors Cables

    Chapter 6: Internal Connectors Cables 6.3.1 Cables The following cables are available from Psion Teklogix: Part Number Description 1050988 USB 4-wire cable—female to open-ended. 1051039 USB 4-wire cable—female to female. 100-Pin Connector For details see Chapter 7: “100-Pin Connector”. Scanner Connector For details see Chapter 8: “Scanner Connector”.
  • Page 71 7.13 Psion Teklogix Serial Endcaps ........

  • Page 73: Chapter 7: 100-Pin Connector

    Note: Names listed here are those used by the WORKABOUT PRO. Signals may have other names in expansion modules, scanner converter boards, or other devices. Figure 7.1 The WORKABOUT PRO 100-Pin Connector Block Diagram 7.1.2 Connector Type The 100-pin connector is an FX6-100S-0.8SV2 receptacle. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 74: Chapter 7: 100-Pin Connector Connector Position And Orientation

    Reset Sleep (ohms) V_IN Power V_IN Power V_IN Power V_IN Power System data Input/output Hi-Z System Output address bus Abbreviations: N/A= not applicable; B = both high and low, Hi-Z = high impedance. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 75: Chapter 7: 100-Pin Connector 100-Pin Connector Pinout

    System data Input/output Hi-Z System Output address bus System data Input/output Hi-Z System Output address bus System data Input/output Hi-Z Abbreviations: N/A= not applicable; B = both high and low, Hi-Z = high impedance. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 76 100 k wait SA16 System Output address bus nSLOT_IOIS16 PCMCIA Input 100 k IOIS16 None SA17 System Output address bus Abbreviations: N/A= not applicable; B = both high and low, Hi-Z = high impedance. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 77 PCMCIA slot Input High 100 k ready InputPin64 GPIO Input 10 k InputPin65 PCMCIA slot Input 100 k card detect Abbreviations: N/A= not applicable; B = both high and low, Hi-Z = high impedance. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 78 Input 100 k Not connected Input PWR_EN FF_DCD UART DCD Input 100 k USB_H1_PSW USB host Output power enable Abbreviations: N/A= not applicable; B = both high and low, Hi-Z = high impedance. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 79: Power And Ground

    Ground (pins 21, 22, 39, 40, 57, 58, 77, 78, 84). The DC_IN line can accept DC power of the following specification:. Pin Name Nominal Voltage Tolerance Maximum Ripple Maximum Current DC_IN 50 mV 2100 mA Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 80: Chapter 7: 100-Pin Connector Data And Address Buses

    FF_RI (Ring Indicator flow-control signal from the expansion device) (pin 91). • FF_DTR (Data Terminal Ready flow-control signal to the expansion device) (pin 93). • FF_RTS (Ready To Send flow-control signal to the expansion device) (pin 95). Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 81: Usb

    HDK software API. These signals are at CMOS levels (0 V to 3.3 V). General-Purpose I/O A number of dedicated GPIO signals are provided. These signals are pre-defined as outputs by Psion Teklogix: • OutputPin71 (pin 71). •...

  • Page 82: Chapter 7: 100-Pin Connector General-Purpose Interrupts

    Table 7.3 PCMCIA Control Signals That Do Not Follow The PXA255/PXA270 Naming Convention PXA255/PXA270 Name On WORKABOUT PRO Notes Name nPWAIT nSLOT_WAIT_SRC PSKTSEL nSLOT_PSKTSEL Low = Expansion PCMCIA interface enabled Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 83: Wakeup

    Chapter 7: 100-Pin Connector Wakeup If the Psion Teklogix PCMCIA driver is used, all of the dual function pins (the general-purpose I/O and interrupt signals) that can be used by the PCMCIA interface will be reserved by the PCMCIA driver. All of these pins conform to the pin functions as defined by the PC Card Stan- dard, Release 8.

  • Page 84: Chapter 7: 100-Pin Connector I2C Addresses

    I2C_SCL (pin 100). These signals are at CMOS levels (0 V to 3.3 V). This identifying EEPROM should be an I2C EEPROM of at least 128 bytes. Psion Teklogix rec- ommends using a serial-access 1-kilobit (128 x 8) EEPROM, such as STMicroelectronics ST24C01 or similar.

  • Page 85: Expansion Module Eeprom Fields

    Revision The version of the specification which defines the layout of the EEPROM and the contents of its 45 byte header. This value is specified by Psion Teklogix and is always set to 1. Hardware revision This is an ASCII character that defines the hardware revision. This field may be used by the driver to vary the operation of the device.

  • Page 86: Chapter 7: 100-Pin Connector Example Expansion Modules

    This field defines the expansion slot hardware. If the expansion module requires a non-Psion Teklogix device driver, this field contains the name of the device driver. The characters allowed in this field are restricted to those that are allowed in a Windows registry key.

  • Page 87: Psion Teklogix Serial Endcaps

    WORKABOUT PRO 2nd. Generation C, S USB Connector All WORKABOUT PRO 2nd. Generation computers have an internal USB connector. Psion Teklogix supplies a cable that connects to this socket. For information see the Accessories catalog at www.PsionTeklogix.com/Accessories. This connector uses the same USB port as the 100-pin connector.

  • Page 88: Chapter 7: 100-Pin Connector Workabout Pro 2Nd. Generation C, S Usb Connector

    Chapter 7: 100-Pin Connector WORKABOUT PRO 2nd. Generation C, S USB Connector Figure 7.5 Internal USB Connector Block Diagram 100-pin connector CN601 USB_H1_D+ USB_H1_D- +5 V Switch Enable USB_H1_PSW Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 89 8.7 Signals To The Scanner Device ........86 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 91: Chapter 8: Scanner Connector

    Psion Teklogix provides scanners modules as either: • A scanner pod, or • A scanner endcap. Scanner Pod Scanners pods provided by Psion Teklogix have the following parts: • Scan engine. • Scanner converter board. • Trigger switch (on some models only).

  • Page 92: Scanner Kits

    The scanner module is connected to the WORKABOUT PRO scanner connector by the scanner flex cable, using an interface defined by Psion Teklogix. Scanner Kits Psion Teklogix supplies several scanner kits. For a complete list see the Accessories Catalog at www.PsionTeklogix.com/Accessories. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 93: Scanner Connector Location

    Ground. Power Abbreviations: N/A= not applicable A= according to design requirements of driver and scanner device B = both high and low L= active low H= active high Hi-Z = high impedance Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 94: Chapter 8: Scanner Connector Scanner Connector Pinout

    Applies only to the WORKABOUT PRO M, C, S, and ME variants. Applies only to the WORKABOUT PRO 2nd. Generation C and S variants. When controlled through software, pins 1, 2, 10, 14, and 19 are switched on and off together. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 95: The Scanner Flex

    PRO. The WORKABOUT PRO is supplied with the scanner flex already attached to the main logic board. The flex used with Psion Teklogix scanners has part number 1040017. The scanner cable is inserted straight down into the connector on the main logic board, and folds over to connect to the scanner device.

  • Page 96: Chapter 8: Scanner Connector Signals To The Scanner Device

    Serial scanner devices can be connected through the following signals on the WORKABOUT PRO 2nd. Generation: • BAR_TXD (data to the scanner device, pin 3). • BAR_RXD (data from the scanner device, pin 5). Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 97 Apart from V+5_BAR, the signals connected to the scanner port are at 3.3 V CMOS lev- els. Use a level translator before the scanner cable to connect 5 V signals to the WORKABOUT PRO main logic board. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 99 9.4.3 Control Signals ........97 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 101: Chapter 9: Example: Scanner Converter Board

    Overview Overview Psion Teklogix provides a scanner converter board in WORKABOUT PRO units that incorporate a scanner. This board is attached to the scan engine, and differs depending on the installed scanner. At a minimum, the scanner board physically connects the supply voltages and signal lines pro- vided by the scanner flex to the scanner device.

  • Page 102: Example: Scanner Converter Board Serial Scanner Board

    None WORKA- BOUT PRO to scanner device Abbreviations: N/A= not applicable; A=- according to design requirements of driver and scanner device, B = both high and low, L= active low, H= active high. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 103 KB_SCAN_CO Keyboard Output Driven None column 0. Abbreviations: N/A= not applicable; A=- according to design requirements of driver and scanner device, B = both high and low, L= active low, H= active high. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 104 Name On Converter Board Description Direction V+5_BAR +5V supply to scan engine Power V+5_BAR +5V supply to scan engine Power Ground Power Note: “Input” and “output” are relative to the WORKABOUT PRO main logic board. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 105 CTS from scan engine to Input WORKABOUT PRO Symbol_PWRDWN Power-down signal from scan engine to Input WORKABOUT PRO. Connected to pin 8. Ground Power Note: “Input” and “output” are relative to the WORKABOUT PRO main logic board. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 106: Chapter 9: Example: Scanner Converter Board Power And Ground

    IR_RXD (data from the scanner device, pin 5). • nBAR_CTS (Clear To Send flow-control signal from the scanner device, pin 7). • nBAR_RTS (Ready To Send flow-control signal to the scanner device, pin 9). Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 107: Usb Signals

    KB_SCAN_C0A (an output, pin 15) These signals can be shorted together for a minimum of 20 milliseconds to initiate a scan or wake up the terminal. On the scanner board, these signals are connected directly to CN3. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 109 10.6 EEPROM Data ..........104 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 111: Example: Pcmcia Expansion Module Overview

    The expansion module connects to the WORKABOUT PRO 100-pin connector. It also has an unkeyed PCMCIA connector. The PCMCIA connector is aligned parallel to the expansion board, on the opposite side to the 100-pin connector. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 112: Chapter 10: Example: Pcmcia Expansion Module Electrical

    The PCMCIA Expansion Module serves as a PCMCIA host bus adaptor for the WORKABOUT PRO, buffering the system data and address buses from the 100-pin connector to the PCMCIA connector. The expansion module incorporates a Psion Teklogix-standard serial EEPROM for identification to the WORKABOUT PRO system. 10.5.1 PCMCIA Compatibility The PCMCIA Expansion Module implements a subset of the PCMCIA standard.

  • Page 113: The Card Detect Signals

    The V+3.3/V+5 line provides the PCMCIA card supply voltage, VCC, on pins 17 and 51 of the PCMCIA connector. It also serves to pull the PC_READY, nPC_BVD1, nPC_VS1, nPC_WAIT_SRC, and nPC_IOIS16 lines high, maintaining compatibility between these signals and the PCMCIA card. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 114: Chapter 10: Example: Pcmcia Expansion Module

    0x4d, 0x43, 0x49, 0x41 6) Serial number 33-44 12 bytes ASCII text, as appropriate. Example: ‘1234’ is 0x31, 0x32, 0x33, 0x34, 0x00. The remaining locations are not programmed, and contain 0xff 7) Manufacturer-specific All 0xff Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 115 11.7 Installation ..........119 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 117: Overview

    This chapter describes the Multi-I/O Expansion Module for the WORKABOUT PRO. This product is no longer supplied by Psion Teklogix. These instructions are intended to give you guid- ance in the design and implemention of an expansion module for the WORKABOUT PRO. They build on the information in Chapter 4: “Mechanical Considerations”, Chapter 7: “100-Pin Con-...

  • Page 118: Schematics

    • Connector for the UART on the 100-pin connector (the FFUART) (J5). • Connector for the USB host on the 100-pin connector (USB host 1) (J6). • Power connector (Ground and +5V) (J7). Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 119: Chapter 11: Example: Multi-I/O Expansion Module

    Data from scanner device to Input None WORKABOUT PRO. At RS-232 levels +5V_SCANNER Regulated 5 V supply from Power WORKABOUT PRO Abbreviations: N/A= not applicable; B = both high and low, L= active low Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 120: Chapter 11: Example: Multi-I/O Expansion Module Usb Host Port 2 Connector (J4)

    N/A= not applicable; B = both high and low 11.3.5 The FF UART Serial Connector (J5) The serial connector from the FF UART (on the WORKABOUT PRO 100-pin connector) has the following pins: Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 121 TTL levels through SJ15 FF_CTS Clear To Send signal from Input Pulled 100 kΩ scanner device to WORKA- BOUT PRO Configurable for RS-232 or TTL levels through SJ14 Abbreviations: N/A= not applicable; L= active low Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 122: Chapter 11: Example: Multi-I/O Expansion Module The Usb Host 1 Connector (J6)

    USB_H1_D+ USB host port 1 D+ Bidirec- Pulled 15 kΩ tional down +3.3V Regulated 3.3 V supply from Power expansion module. Abbreviations: N/A= not applicable; B = both high and low Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 123: The Power Connector (J7)

    Configure the output voltage for the standard-power option. (See “Voltage Configuration For Standard-Power Output” on page 115.) • Configure the FORCEON and FORCEOFF/ control signals for the RS-232 converter on the FFUART port. (See “Control Signals For FFUART Level Converter” on page 117.) Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 124: Chapter 11: Example: Multi-I/O Expansion Module Slot Power Control

    1 and 2 Power controlled by SLOT_PWR_EN 2 and 3 Power always enabled Pad 2 is pulled up to +VIN. 11.4.2 EEPROM Write Control Jumper SJ2 selects write control for the EEPROM. 3 2 1 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 125: Chapter 11: Example: Multi-I/O Expansion Module Voltage Configuration For Standard-Power Output

    Important: Use these resistors and jumpers ONLY if U4 and its associated components for the standard-power output are installed. These components are indicated as “Option Standard Power (SP)” in the schematic on page B-3. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 126: Chapter 11: Example: Multi-I/O Expansion Module Voltage Configuration For High-Power Output

    ⎠ 1.24 Important: Use these resistors and jumpers ONLY if U1 and its associated components for the high-power output are installed. These components are indicated as “Option High Power (HP)” in the schematic. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 127: Control Signals For Ffuart Level Converter

    FORCEOFF/ signal controlled by GPIO44 (pin 76 on the 100-pin connector). 2 and 3 FORCEOFF/ signal tied to 3.3 V. Note: Refer to the data sheet for the MAX3243 for the use of these signals. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 128: Chapter 11: Example: Multi-I/O Expansion Module Ttl Output Option For Scanner Serial Port

    Ground (pins 1, 2, 11, 12, 15). • +5V_SCANNER (pins 21and 22). This voltage is +5 V from a DC-DC converter fed by V_IN, the WORKABOUT PRO main supply. It is switched by the scanner power enable signal. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 129: Eeprom Data

    The scanner cable fits straight between the scanner connector in the WORKABOUT PRO and the scanner connector on the Multi-I/O Expansion Module. It may need to be folded. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 130 Chapter 11: Example: Multi-I/O Expansion Module Installation Figure 11.4 Arrangement Of Cable Between Main Logic Board And Multi-I/O Expansion Module Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 131: Technical Support

    UPPORT ERVICES ORLDWIDE FFICES Psion Teklogix provides a complete range of product support services to its customers worldwide. These services include technical support and product repairs. Technical Support For technical support in North America: Call Toll free: +1 800 387 8898...

  • Page 132: Worldwide Offices

    A.3.3 North American Headquarters And U.S. Service Centre Psion Teklogix Corp. 1810 Airport Exchange Boulevard Suite 500 Erlanger, Kentucky USA 41018 Tel: +1 859 371 6006 Fax: +1 859 371 6422 E-mail: salesusa@psion.com Psion Teklogix WORKABOUT PRO HDK Developer Guide...

  • Page 133: International Subsidiaries

    See also www.psionteklogix.com/Subsidiaries. Psion Teklogix S.A. La Duranne 135 Rue Rene Descartes BP 421000 13591 Aix-En-Provence Cedex 3; France Tel: +33 4 42 90 88 09 Fax: +33 4 42 90 88 88 E-mail: tekeuro@psion.com Psion Teklogix WORKABOUT PRO HDK Developer Guide...

  • Page 135: Appendix B: Resources

    ESOURCES Psion Teklogix WORKABOUT PRO User Manuals The following user manuals are available at www.PsionTeklogix.com/manuals: • Psion Teklogix. 2004. WORKABOUT PRO M/C Hand-Held Computer User Manual (Part number 8000024). • Psion Teklogix. 2005. WORKABOUT PRO Hand-Held Computer With Windows Mobile 2003 SE User Manual (Part number 8100058).

  • Page 137: Specifications

    C.4.2 High-Capacity Battery Pack ........6 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 139: Appendix C: Specifications Workabout Pro M

    Hand-Held Computer Specifications WORKABOUT PRO M Hand-Held Computer Specifications WORKABOUT PRO M Note: Performance specifications are nominal & subject to change without notice. Note: The WORKABOUT PRO M is no longer available from Psion Teklogix. Model • WORKABOUT PRO M - Model 7225M Size •...

  • Page 140: Radio Specifications

    50mW max for EU countries Frequency Range 2.400-2.474 for USA, Canada 2.400-2.484GHz for EU Channels 1 to 11 for USA, Canada 1-13 for EU countries 1-13 or 14 for Japan Data Rates 1,2,5.5 and 11Mbps Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 141: Scanner Options

    Discharge Tempera- -20° C to 60° C (-4° F to 140° F) ture -20° C to 60° C (-4° F to 140° F) Storing battery at elevated Storage Temperature temperatures is not recommended. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 142: High-Capacity Battery Pack

    Taper Current Recommended Charge 30 min. Termination Timeout Charge Temperature 0° C to 45 °C (32° F to 113° F) Discharge Temperature -20° C to 60° C (-4° F to 140° F) Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 143 -20° C to 45° C (-4° F to 113° F) >75% capacity recovery Capacity recovery within 3 month -20° C to 20° C (-4° F to 68° F) >70% capacity recovery within 1 year Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 145 D.8 Battery Options ..........7 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 147: Appendix D: Specifications Workabout Pro C, S & Me

    Sunlight readable. • Passive stylus or finger operation. • Signature capture capability. Keyboard • 55-key alphanumeric keyboard. • Keyboard backlight. • High durability, hard-topped keys. Memory • 64 MB Flash. • 128 MB RAM. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 148: Workabout Pro S Variant

    Depth: 31 mm (1.2") at grip area, tapering to 42 mm (1.7") at display area. Weight • With battery: 454 g (16 oz); - with SE 1223HP scanner expansion module: add 75 g (2.6 oz). - with 802.11g CF card radio: add 19g (0.7 oz). Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 149: Workabout Pro C, S, And Me Variants

    3.7 V High-Capacity Li-ion rechargeable battery - up to 12 hours of operation. • Advanced Smart Battery w/ gas gauge. • Quick swap battery packs. • Built-in fast charger. • Rechargeable, user-replacable internal coin battery. • Also accepts 3 AA alkaline batteries. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 150 USB interface supports GPS interface. • 100-pin expansion interface supports: - PCMCIA (type II). - GSM/GPRS EDGE. - Customized expansion modules developed using the WORKABOUT PRO HDK. • Flex cable interface with robust connector supports - Scanner (serial) modules. - Imager (USB) modules.

  • Page 151: Radio Options

    SX5393 Imager Battery Options For details of these batteries see Appendix H: “Specifications WORKABOUT PRO Batteries”. • Standard Capacity–2000 mAh (Model WA3000-G1.) • High Capacity–3000 mAh (Model WA3006). • Maxell ML2032 Rechargeable Coin Battery. Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 153 E.4.1 Scanner/Imager Model Numbers ....... . 8 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 155: Appendix E: Workabout Pro 2Nd. Generation

    High durability, hard-topped keys. E.1.3 WORKABOUT PRO All Variants Display • Colour touch screen display • Diagonal measurement: 9.144 cm (3.6 in). • Full VGA: 480 pixels by 640 pixels. • Transflective, portrait mode TFT. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 156: Workabout Pro All Variants

    • EGPRS Class B, Multi-Slot Class 12 • Integrated Bluetooth class II, ver 1.2 • Working Range:16.4 ft.to 32.81 ft. (5 m to 10 m). Note: 802.11b/g, GSM, and Bluetooth are available simultaneously. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 157: Bar Code Applications

    • Passive stylus or finger operation • Signature capture • Keyboards • Full Alpha-Numeric (C model) • Numeric (S model) • Ergonomically enhanced for ambidextrous, one-hand operation • Backlit, high durability hard-capped keys Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 158: Programming Environment

    Windows sockets (CE .NET) Application Software • Internet Explorer 6.0 incl.with Windows CE 5.0 • Unique Psion Teklogix Voice Dialer and Contacts Manager incl.Windows CE 5.0 • PTX Connect VoIP • Optional Open TekTerm terminal emulation software, supports IBM 5250,IBM 3270, HP2392, ANSI and TESS •...
  • Page 159 Hand-strap, pistol grip with trigger, holster and various protective carrying cases and pouches. Approvals Safety: CSA/UL60950-1, IEC 60950-1, EN60950-1 EMC: FCC Part 15 Class B EN 55022 EN 55024 EN 301 489 Laser: IEC 60825-1, Class 2 FDA 21 CFR 1040.10. 1040.11 Class II Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 160: Radio Options

    Scanner/Imager Kit Model Number Form Factor Engine 1D Laser SE955 WA9102-G1 Endcap without GSM WA9112-G1 Endcap with GSM WA9002-G1 1D Laser WA9000-G1 SE1223HP 1D Laser WA9005-G1 SE1223LR 1D Laser WA9006 Pod (non-RoHS) SE1223ALR Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 161 WA9103-G1 Endcap without GSM WA9113-G1 Endcap with GSM WA9003-G1 2D Imager WA9010 Pod (non-RoHS) SX5393 WA9007-G1 Slim Pod 2D Imager HHP WA8010-G1 Endcap without GSM 5180 WA8110-G1 Endcap with GSM WA9012-G1 Slim Pod Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 163 F.5 Bluetooth Radio ..........5 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 165: Appendix F: Specifications Workabout Pro Radios

    ETSI: TELEC: RX Sensitivity -96dBm @ 1Mbps, -90dBm @ 11Mbps, -94dBm @ 6Mbps, -75dBm @ 54Mbps Data Rates 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b: 1, 2, 5.5, 11 Mbps Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 166: Gsm/Gprs/Edge Radio (Model Ra3030-G2

    Point-to-point MO and MT SMS cell broadcast Text and PDU mode Fax: Group 3, class 1 Voice: Triple-rate codec for HR, FR, and EFR Adaptive multi-rate AMR Basic hands-free operation Echo cancellation Noise reduction Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 167: Bluetooth Radio

    Chip Antenna 2dBi peak Transmit Power -3dBm (0.5mW) minimum, +4dBm (2.5mW) max Frequency Range 2.400 - 2.4835 GHz RX Sensitivity -80dBm max (BER<=0.1%) Data Rate 732.2 kbps and 57.6 kbps asymmetric, 433.9 kbps symmetric Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 169 G.3.4.1 SX5400 Imager Decode Zone ......11 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 171: Appendix G: Specifications Scanners And Imagers

    Minimum 40% Minimum Minimum absolute absolute 40% absolute 25% absolute dark/light dark/light dark/light dark/light reflectance reflectance reflectance reflectance measured at measured at measured at measured at 650 nm 650 nm 650 nm 650 nm Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 172: Se 1223Hp Decode Zone

    G.2.1.2 SE 1223LR Decode Zone 4,844 Lux to 86,112 Lux Minimum Maximum Width of field Width of field range range Mil Size Inches Inches Inches Inches High quality symbols in normal room light. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 173: Se 1223Alr Decode Zone

    UPC 100% 1.5 in. - 23.5 in. / 3.81 cm - 59.69 cm 15 mil 1.5 in. - 29.5 in. / 3.81 cm - 74.93 cm * dependent on width of bar code Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 174: Imager Specifications

    2000G, 0.7ms, half sinus, 3 axes Vibration 50G r.m.s G.3.1.1 EV15 Imager Decode Zone 0 Lux to 100,000 Lux Minimum range Maximum range Mil Size Inches Inches 14.5 35.5 High quality symbols in normal room light. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 175: Hhp5180 Imager Specifications

    18 shocks of 3,500 G for 0.5 msec at 23°C (73° F) G.3.2.1 HHP5180 Imager Decode Zone Performance Focal Point 7 inches (17.8 cm) from lens plate 4.5 inches (11.4 cm) from lens plate *Data characterized at 23°C and 0 lux ambient light. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 176: Sx5393 Imager Specifications

    3.6 Volt DC nominal (2.7 - 5 Volts DC) Connectivity USB 1.1 or serial async Connector to the interface Molex 52892-1295 or HiRose FH12-12S-.5SH board *Data characterized at 23°C and 0 lux ambient light. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 177: Sx5393 Imager Decode Zone

    *Data characterized at 23°C and 0 lux ambient light. G.3.3.1 SX5393 Imager Decode Zone 2D Bar Codes 300 Lux With Good Quality Bar Codes Minimum range Maximum range Mil Size* Inches Inches 15** 20.8 11.7 *QR code **Data Matrix Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 178: Sx5400 Imager Specifications

    5 V ± 10% Power supply 3.6 Volt DC nominal (2.7 - 5 Volts DC) Connectivity USB 1.1 or serial async Connector to the interface board Molex 52892-1295 or HiRose FH12-12S- .5SH G-10 Psion Teklogix WORKABOUT PRO HDK User Manual...
  • Page 179 Size (mil) (inches) (inches) (inches) 2.75 9.25 2.25 11.0 8.75 PDF6.6 PDF10 3.25 5.75 PDF15 2.25 10.75 DM15 QR15 3.75 3.75 12.5 Typical performance at 300 lux for the SX5400 @160mm focus Psion Teklogix WORKABOUT PRO HDK User Manual G-11...
  • Page 181 H.5 Maxell ML2032 Rechargeable Coin Battery ......13 H.6 WORKABOUT PRO 2nd. Generation (C And S) Internal Battery ....13 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 183: Appendix H: Specifications Workabout Pro Batteries

    Internal Resistance 150 mΩ Maximum Battery Pack Electrical Specifications Description Specification Minimum Typical Maximum Over voltage detection 4.325V 4.350V 4.375V voltage Charge enable 4.10V 4.15V 4.20V Under voltage detection 2.5V 2.6V 2.7V voltage Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 184: Standard Discharge

    Self discharge After a standard charge, keep battery at 25°C 100 minutes or more for 30 days. Measured the time taken for a fast discharge. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 185: Environmental Test

    Random vibra- tion 5Hz-500Hz ASD 0.02g2/Hz in 3 axis for 15 mins. Followed by stand- ard discharge, charge, discharge. No parting joints/cracks or damage to connectors. No leakage or critical damage. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 186: High-Capacity 3000Mah (Model Wa3006

    Short-circuit detection voltage 150mV 200mV 250mV Over voltage delay time 0.8s 1.2s Under voltage delay time 90ms 100ms 110ms Over current delay time 10ms 20ms Short-circuit delay time 160µs 200µs 240µs Recovery charge current 0.5mA Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 187: Standard Discharge

    After standard charge, keep the battery at 60°C 100 minutes or more for 8 hrs. Carry out a fast discharge, standard charge and then a fast discharge, measured the time taken for the second discharge. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 188: Safety Data

    Test Reference Test Condition/Result Drop (mechanical) Drop sample battery on all faces from height of 1.2 meters onto concrete floor. No explosion, fire, vent, leakage and the open circuit voltage higher than 3.7V. Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 189: Super High-Capacity (Model Wa3010

    Rated Capacity 4000mAh Typical Rated Charge Current 1.2A Maximum Charge Voltage 4.2 +/- 0.05V Maximum Discharge Cut-Off Voltage 2.6V Typical Charge Method Constant voltage Current limited Discharge Current 0.5C (-20°C to 60°C) Typical Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 190: Standard Discharge

    After standard charge, measure time taken for 110 minutes or more a fast discharge. Charge/Discharge After repeating standard charge and fast dis- 90 minutes or more Cycle charge, measure the fast discharge time after 300 discharge cycles. H-10 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 191: Safety Data

    Safety Data Description Condition Test Condition/Result Short Circuit Test After a standard charge, Protection circuit board to operate. short terminals and dis- No explosion, fire, smoke, charge for 1 hr. or leakage. Psion Teklogix WORKABOUT PRO HDK User Manual H-11...

  • Page 192: Safety License

    +60°C (2C) for 1 hour (T1), -20oC (2C) cycling for 1 hour. 3 minutes Max allowed for change between T1 and T2. Cycle 10 times No explosion, no fire, no vent, and no leakage. H-12 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 193: Maxell Ml2032 Rechargeable Coin Battery

    Maximum continuous 260 mA discharge current Operating Temperature -20° C to 60° C (-4° F to 140° F) Range Charging Temperature 0° C to 45° C (32° F to 113° F) Range Psion Teklogix WORKABOUT PRO HDK User Manual H-13...
  • Page 195 I.10 GENERAL ..........I-5 Psion Teklogix WORKABOUT PRO HDK User Manual...

  • Page 197: Appendix I: Hardware Developer Kit License Agreement

    Agreement, we do not grant you a license to the HDK, and you may not install or use the HDK or any accompanying documentation. The HDK is the property of Psion Teklogix Inc. or its licensors and is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The HDK is licensed, not sold.

  • Page 198: High Risk Activities

    COPYRIGHTS, OWNERSHIP AND PROPRIETARY RIGHTS All title and copyrights in and to the HDK, and any copies thereof, are owned by Psion Teklogix Inc. or its suppliers. The HDK also contains copyrighted material licensed from our suppliers and all rights to such copyrighted material rests with such suppliers.

  • Page 199: Confidentiality

    In such event, you must return or destroy all copies and component parts of the HDK and documentation, as well as any other Psion Teklogix proprietary information in your pos- session, within fourteen (14) days of the date of termination. Any rights and obligations under this Agreement that by their nature continue after it ends, will remain in effect until they are completed.

  • Page 201: Index

    COM port EEPROM on scanner connector 87 COM ports addresses for 74 defailt 24 circuit in expansion module 74 data format for 75 configuration in Multi-I/O Expansion Module 119 of Multi-I/O Expansion Module 113 Psion Teklogix WORKABOUT PRO HKD User Manual...
  • Page 202 4 obtaining 6 LED 15 high-capacity battery pack (WA3006) 8, 6 LIF connector block diagram of 52, 53, 55 pinout 50 insertion location scanner cable 85 card stop 36 expansion module connector 35 Psion Teklogix WORKABOUT PRO HKD User Manual...
  • Page 203 92 nSLOT_PSKTSEL signal 103 PXA255 11 nSLOT_PWR_EN signal 103 nSLOT_PWR_SEL signal 103 nSLOT_RST signal 103 quad cradle nSLOT_VS1 signal 103 block diagram of 52 nSLOT_5V_EN signal 103 obtaining HDK 6 operating systems 7 Psion Teklogix WORKABOUT PRO HKD User Manual...
  • Page 204 16 power and ground on 96 trigger-switch connector 96 signals on 96 TTL output option for scanner serial scanner device 81 enabling jumpers on Multi-I/O Expansion Module models 35 weight 35 Psion Teklogix WORKABOUT PRO HKD User Manual...
  • Page 205 3 variants 6, 11 zero-ohm resistor (jumper) 91 100-pin connector location 35 on Multi-I/O Expansion Module 109 power and ground on 69 signals on 63 wakeup input on 73 802.11b/g radio 3 Psion Teklogix WORKABOUT PRO HKD User Manual...

Table of Contents