1. Manuals
  2. Brands
  3. NI Manuals
  4. Cables and connectors
  5. SCB-12
  6. Safety, environmental, and regulatory information

NI SCB-12 Safety, Environmental, And Regulatory Information

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SCB-12 Safety,
Environmental,
and Regulatory
Information
2022-07-11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCB-12 and is the answer not in the manual?

Questions and answers

Related Manuals for NI SCB-12

Summary of Contents for NI SCB-12

  • Page 1 SCB-12 Safety, Environmental, and Regulatory Information 2022-07-11...
  • Page 2 SCB-12 Purpose and Introduction........

  • Page 3: Icon Definitions

    SCB-12 Safety, Environmental, and Regulatory Information SCB-12 Purpose and Introduction This document provides safety, environmental, and regulatory information, connection instructions, and specifications for the SCB-12. Icon Definitions Notice Take precautions to avoid data loss, loss of signal integrity, degradation of performance, or damage to the model.

  • Page 4: Safety Cautions

    Notice Connect only voltages that are below the limits described in the specifications document for the FlexRIO module you will connect to the SCB-12. You can search for specification documents by product name at ni.com/manuals. Notice When you have finished using the SCB-12, power off any external signals connected to the SCB-12 before you power off your computer.

  • Page 5: Safety Standards

    SCB-12 Safety, Environmental, and Regulatory Information Attention Ne pas connecter le produit à des signaux dans les catégories de mesure II, III ou IV et ne pas l'utiliser pour effectuer des mesures dans ces catégories. Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage.

  • Page 6: Electromagnetic Compatibility Standards

    Furthermore, any changes or modifications to the product not expressly approved by NI could void your authority to operate it under your local regulatory rules. Notice Operate this product only with shielded cables and accessories.

  • Page 7: Additional Required Items

    SCB-12 Safety, Environmental, and Regulatory Information Note For EMC declarations, certifications, and additional information, refer to the Product Certifications and Declarations section. What You Need to Get Started Figure 1. SCB-12 Kit Contents or y ce ss B -1 ko ut...
  • Page 8 NI 9913 DIN rail mounting kit (NI part number 781740-01) ■ Preparing the FlexRIO Module 1. Install and configure the FlexRIO module you want to connect to the SCB-12. Note For installation and configuration instructions, refer to the Getting Started Guide for your product, accessible at ni.com/...
  • Page 9 SCB-12. Search for specification documents by product name at ni.com/manuals. Connecting to the SCB-12 The SCB-12 enables access to DIO signals from a Molex™ Nano-Pitch I/O™ cable through other common connectors. To use the SCB-12, you must first connect a Molex™ Nano-Pitch I/O™ cable to your FlexRIO module.
  • Page 10 Notice Using signal voltages outside of the range specified for the FlexRIO module you connect to the SCB-12 could damage the SCB-12 and any instruments connected to it. For maximum voltage specifications, refer to the documentation for the connected hardware. NI is not liable for any damage resulting from using voltages outside of the recommended range.
  • Page 11 PCB mounting screws. 2. Align the 8-pin female connector included in your kit to the DIO spring terminals and the retention screw holes on the SCB-12 front panel. Use a 2.5 mm flathead screwdriver to loosely screw the attached retention screws into the front panel.
  • Page 12 SCB-12 kit, NI part number 723537-01, to power an optical QSFP or QSFP+ cable. 3. The power LED on the SCB-12 front panel indicates a connection to external power. After connecting the external power supply included in your kit, ensure the power LED is lit.
  • Page 13 Mounting the SCB-12 on a DIN Rail with the NI 9913 Mounting Kit The NI 9913 DIN rail mounting kit contains a clip for mounting the SCB-12 on a standard 35 mm DIN rail. The four holes on the bottom of the SCB-12 allow it to be mounted in multiple orientations.

  • Page 14: Specifications

    Specifications DIO Signal Specifications Note For DIO signal specifications, refer to the specifications document for the FlexRIO module you want to connect to the SCB-12. Search for specification documents by product name at ni.com/manuals. MGT Specifications Line rate 10.3125 Gb/s...

  • Page 15: Operating Environment

    Compliance and Certifications Product Certifications and Declarations Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for NI products, visit ni.com/product-certifications, search by model number, and click the appropriate link.
  • Page 16 NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers. For additional environmental information, refer to the Commitment to the Environment web page at ni.com/environment.
  • Page 17 NI product. Product registration facilitates technical support and ensures that you receive important information updates from NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504, USA. For up-to-date contact information for your location, visit ni.com/contact.

Table of Contents