Focal MOOG 914-X Series User Manual
Focal MOOG 914-X Series User Manual

Focal MOOG 914-X Series User Manual

Modular multiplexer system
Table of Contents

Advertisement

Quick Links

MOOG PROPRIETARY AND CONFIDENTIAL INFORMATION
THIS TECHNICAL DATA/DRAWING/DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO, AND IS THE EXPRESS PROPERTY OF MOOG
INC., OR MOOG INC. SUBSIDIARIES EXCEPT AS EXPRESSLY GRANTED BY CONTRACT OR BY OPERATION OF LAW AND IS RESTRICTED TO USE BY
ONLY MOOG EMPLOYEES AND OTHER PERSONS AUTHORIZED IN WRITING BY MOOG OR AS EXPRESSLY GRANTED BY CONTRACT OR BY
OPERATION OF LAW. NO PORTION OF THIS DATA/DRAWING/DOCUMENT SHALL BE REPRODUCED OR DISCLOSED OR COPIED OR FURNISHED IN
WHOLE OR IN PART TO OTHERS OR USED BY OTHERS FOR ANY PURPOSE WHATSOEVER EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY
MOOG INC. OR MOOG INC. SUBSIDIARY.
Model 914-X Series
Modular Multiplexer System
User Manual
Focal Technologies Corporation
A Moog Inc. Company
77 Frazee Avenue
Dartmouth, Nova Scotia, Canada, B3B 1Z4
Tel: (902) 468-2263 | www.moog.com/focal
Document No.:
914-0601-00
Revision:
6.0
Author(s):
E. Mullaley
K. MacIsaac
R. Prout
Date of Issue:
2025-04-01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MOOG 914-X Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Focal MOOG 914-X Series

  • Page 1 Focal Technologies Corporation A Moog Inc. Company 77 Frazee Avenue Dartmouth, Nova Scotia, Canada, B3B 1Z4 Tel: (902) 468-2263 | www.moog.com/focal Model 914-X Series Modular Multiplexer System User Manual Document No.: 914-0601-00 Revision: Author(s): E. Mullaley K. MacIsaac R. Prout...
  • Page 2: Document Revision History

    • 6.3: 914-AX: Removed mentions of 914-0401-00 Diagnostic GUI, updated with 914-0401-04 Unified Diagnostic GUI information • 6.4: 914-DX: Added new section for 914-DX expansion card Focal Technologies Corporation Page ii A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 3 914-2022-00 Model 914-EX Configuration Drawing 914-2023-00 Model 914-AX Configuration Drawing 914-2025-00 Model 914-FOS Configuration Drawing 914-2026-00 Model 914-SPLIT Configuration Drawing 700-0271-00 AIB Plug-in Module User Manual Focal Technologies Corporation Page iii A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 4: Table Of Contents

    914-HDE Serial Configuration ......................5-18 5.5.4 914-HDE Ethernet Configuration ...................... 5-18 5.5.5 914-HDE Low Speed Expansion Configuration ................5-19 914-HDE Optical Page ..........................5-20 914-HDE Engineering Status Page ......................5-21 Focal Technologies Corporation Page iv A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 5 914-DX Diagnostic LEDs ........................6-74 6.4.4 914-DX Diagnostic LED Header ....................... 6-75 6.4.5 914-DX Expansion Channel Configuration ..................6-76 6.4.6 914-DX Status Page ......................... 6-77 6.4.7 914-DX Settings Page........................6-79 Focal Technologies Corporation Page v A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 6 8.2.1 914-DC-05 ............................8-9 8.2.2 914-DC-12 ............................8-10 Moog Focal Optical Transceivers ......................9-1 10.0 914-X Series System Installation and Operation ................... 10-1 10.1 Installation ..............................10-1 10.2 Card Stacking ............................10-2 10.3 914-X Series Expansion Interface Ribbon Cables .................. 10-3 10.4 914-X Series Bench Test .........................
  • Page 7 13.9 SFP Optical Transceiver Part Numbers ....................13-11 13.10 914-X Series High Speed Ribbon Cable Part Numbers ................ 13-13 14.0 Troubleshooting ............................14-1 14.1 Moog Focal Technical Support Contact Information ................14-5 Focal Technologies Corporation Page vii A Moog Inc. Company...
  • Page 8 Table 6-30: 914-DX Expansion Channel Configuration ..................6-76 Table 6-31: Legacy 914-DX J7 Pinout........................6-82 Table 6-32: Legacy 914-DX Mating Connectors ....................6-82 Table 6-33: Legacy 914-DX Serial Data Connector Pinout .................. 6-82 Focal Technologies Corporation Page viii A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 9 Table 13-24: 914 Pressure Tolerant Optical SFP Part Numbers ............... 13-12 Table 13-25: 914-X Series High Speed Ribbon Cable Part Numbers ............... 13-13 Table 13-26: 914-X Series High Speed Ribbon Cable Included Accessories............ 13-13 Focal Technologies Corporation Page ix A Moog Inc. Company...
  • Page 10 Figure 5-5: x86 Redistributable Install Steps ......................5-3 Figure 5-6: x64 Redistributable Install Steps ......................5-3 Figure 5-7: Moog Focal Website Unified Diagnostic GUI Download Location ............5-3 Figure 5-8: Executable Location ..........................5-3 Figure 5-9: Diagnostic GUI Start Screen ........................ 5-4 Figure 5-10: 914-HDE Stack View ..........................
  • Page 11 Figure 6-14: 914-VDX Voltage and Junction Temperature Information ............... 6-45 Figure 6-15: 914-VDX Expansion Link Information ....................6-45 Figure 6-16: 914-VDX Serial and Analog Video Information ................6-45 Focal Technologies Corporation Page xi A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 12 Figure 6-72: 914-DX Factory Power Input Connector Location ................6-73 Figure 6-73: 914-DX Diagnostic LED Locations ....................6-74 Figure 6-74: 914-DX Diagnostic LED Header ...................... 6-75 Focal Technologies Corporation Page xii A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 13 Figure 7-36: 914-HDV2 Top View (Board Revisions 3.3 and Earlier) ..............7-16 Figure 8-1: 914-CWDM Optics Card ........................8-1 Figure 8-2: 914-CWDM Connection Diagram ......................8-1 Focal Technologies Corporation Page xiii A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 14 Figure 10-14: 914-HDV2 Dimensions (inches [mm]) ..................10-11 Figure 11-1: Firmware Update GUI ........................11-1 Figure 12-1: 914-HDE Engineering Settings Page ....................12-1 Figure 12-2: Feature Update Via Configuration Tool ................... 12-1 Focal Technologies Corporation Page xiv A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 15 Small Form-factor Pluggable (Optical Transceiver) Surface Mount Technology Time Division Multiplexer / Multiplexing Transistor-Transistor Logic Composite Video, Serial Data, EXpansion VOAT Variable Optical Attenuator Wavelength Division Multiplexer / Multiplexing Focal Technologies Corporation Page xv A Moog Inc. Company Document Number: 914-0601-00, Rev. 6.0...
  • Page 16: Introduction

    Model 914-X Series Modular Multiplexer System User Manual Introduction The Moog Focal Model 914-X Series Modular Multiplexer System is a compact and rugged transmission system designed for industrial environments and other applications that require transmission of HD video, serial data, and Ethernet over an optical link.
  • Page 17: Model 914-X Series Benefits

    • Pigtailed power plug and cable for the 914-HDE Motherboard • Modules individually packaged with configuration drawings • 914-0401-04 914-X Series Diagnostic GUI – downloadable from www.moog.com/focal/914-x-series, or see Section 5.1 Default configuration settings • Moog Focal direct support •...
  • Page 18: Safety Precautions

    Do not look into the end of a fiber when it is plugged into a transceiver or active fiber, especially when using a magnifying instrument, such as a fiber microscope. Handle optical fiber with extreme care. Glass fiber is subject to breakage if mishandled. Focal Technologies Corporation Page 1-3 A Moog Inc. Company...
  • Page 19: Setup Procedure

    Verify all system voltages in the 914-X Series Diagnostic GUI. Refer to Section 4.2 for information on applying power to the 914-HDE. Refer to Section 5.0 for an overview of the GUI. Focal Technologies Corporation Page 2-1 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 20 See Section 5.9.1. Verify and monitor FPGA and SFP temperatures and voltages during operation using the 914-X Series Unified Diagnostic GUI. All values should remain green. Focal Technologies Corporation Page 2-2 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 21: System Overview

    CWDM Selects between two optical 914-FOS ― ― ― ― fibers for redundant operation Splits an optical signal for 914-SPLIT ― ― ― ― redundant operation Focal Technologies Corporation Page 3-1 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 22: Defining A 914-X Series System

    An expansion connector on the 914-HDE supports eight expansion card ports: four low speed (LS) and four medium speed (MS). Expansion cards allow a full, customized system to be built using the 914-HDE Motherboard as the base optical card. Optional expansion cards are detailed in Section 0. Focal Technologies Corporation Page 3-2 A Moog Inc. Company...
  • Page 23: Figure 3-2: 914-X Series System With Expansion Cards Example

    For larger systems requiring more optical bandwidth than a single 914-X Series stack can provide, Moog Focal has a series of CWDM products that allow many optical data streams to be combined onto a single fiber. These cards can handle the addition of 2, 4, 6, 8 or more systems onto a single fiber.
  • Page 24: Figure 3-4: 914-X Series System With 914-Hdv2 And Cwdm Example

    This example system has 3x HD video channels, 2x NTSC/PAL channels, 3x Gigabit Ethernet channels and 6x serial data channels, all combined in real time onto a single bidirectional fiber link. Figure 3-4: 914-X Series System with 914-HDV2 and CWDM Example Focal Technologies Corporation Page 3-4 A Moog Inc. Company...
  • Page 25: System Specification

    When specifying a 914-X Series system, ensure there is enough available optical bandwidth to support the required signals and data throughput. Moog Focal has released three versions of the 914-HDE motherboard with pricing linked to bandwidth. This allows users who do not require expansion cards, 3G-SDI, or gigabit Ethernet to select a more cost-effective solution.
  • Page 26: Example 914-X Series L1 System

    12x Serial channels (6 per card) 2x Low speed 2x Analog video 914-VDX 1x Medium speed 4x Serial 914-EX 2x Fast Ethernet channels 1x Medium speed Focal Technologies Corporation Page 3-6 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 27: Example 914-X Series H1 System

    For systems requiring more than a single 914-X Series stack with a single fiber bidirectional transceiver, an optical CWDM card may be used to combine more signals onto the same fiber. Please refer to Section 8.0 for more details. Focal Technologies Corporation Page 3-7 A Moog Inc. Company...
  • Page 28: 914-Hde Motherboard Overview

    Different versions of the 914-HDE are available depending on system requirements. Each version supports different optical bandwidths and expansion cards. Version upgrades are possible. Please contact Moog Focal for availability. For more information regarding the expansion cards, system bandwidth capabilities, and system configurations, please consult Sections 6.0 and 3.3.
  • Page 29: 914-Hde Power

    The onboard surface mount fuse, F1, is rated to 2A and is not intended to be field replaceable. If the power fuse is blown, the card should be evaluated for damage by the Moog Focal factory or a trained service personnel prior to any repair.
  • Page 30: 914-Hde Hd Video Channel

    Video latency through the mux/demux system is less than 50 µs, not including fiber delays of 5 us/km. Figure 4-3: 914-HDE Mini SMB Jack – Amphenol P/N 142146-75 Figure 4-4: 914-HDE Video Channel 1 Connector Location Focal Technologies Corporation Page 4-3 A Moog Inc. Company...
  • Page 31: 914-Hde Serial Data Ports

    Connect only one tx output Do not connect Isolated ground is shared between the ports Figure 4-5: 914-HDE Molex Micro-fit P/N 43045-0800 Figure 4-6: 914-HDE Serial Ports 1 and 2 Focal Technologies Corporation Page 4-4 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 32: 914-Hde Ethernet Port

    # Bytes * 0.008 µs OL (Optical Latency) 5 µs / km 5 µs / km 5 µs / km Total Latency = FEL + FT + OL Focal Technologies Corporation Page 4-5 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 33: 914-Hde Diagnostic Leds

    Flashing LED indicates serial Channel 2 is transmitting to external equipment. Yellow Flashing LED indicates serial Channel 2 is receiving from external equipment. Figure 4-8: 914-HDE Diagnostic LED Locations Focal Technologies Corporation Page 4-6 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 34: 914-Hde Diagnostic Led Header

    Flashing LED indicates serial Channel 2 receive activity. Active low. SER2 TX Flashing LED indicates serial Channel 2 transmit activity. Active low. Ground Figure 4-10: 914-HDE Diagnostic LED Header Focal Technologies Corporation Page 4-7 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 35: 914-Hde Optics

    Due to the high data rates, singlemode fiber is standard. Multimode fiber is only suitable for very short links (< 300 m). Contact Moog Focal for multimode options. Typical link budgets for singlemode fiber are 20 dB for bidirectional single fiber, or 24 dB for dual fiber CWDM. Moog Focal has compatible CWDM modules that can be mounted and stacked with 914-HDE systems.
  • Page 36: Legacy 914-Hde Information (Board Rev. 5 And Earlier)

    REV 6 AND LATER ISO GND Table 4-11: Legacy 914-HDE Mating Connectors DESIGNATOR DESCRIPTION MFR. PART NUMBER / FOCAL PN CRIMP PINS / FOCAL PN J8 (≤ Board Rev 3) Diagnostics (Old revs) Molex 0781720003 / EL-J0579 0781720410 / EL-J0580 J8 (≥...
  • Page 37: Model 914-X Series Unified Diagnostic Gui

    Figure 5-2: 914-HDE Diagnostic Interface Cable Note that in 914-HDE board revisions 3 and earlier, the diagnostic interface cable and connector is different. Refer Section 4.9.1 for details. Focal Technologies Corporation Page 5-1 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 38: Table 5-1: 914-Hde J8 Diagnostic Connector Pinout

    RS232 RX (Data from PC GUI) Table 5-2: 914-HDE J8 Diagnostic Connector Part Numbers PART NUMBER Connector Molex Pico-Clasp 501953-0305 Mating Plug assembly Molex Pico-Clasp 0151330306 Focal Technologies Corporation Page 5-2 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 39: Installing The Model 914-X Series Unified Diagnostic Gui

    Figure 5-7: Moog Focal Website Unified Diagnostic GUI Download Location Navigate to the location which the *.zip file downloaded and extract it to “C:\Focal\”. Open the extracted file and double click on the 914-X Series Unified Diagnostic GUI executable to run the GUI.
  • Page 40: Connecting Hardware To The Gui

    914-VDX, 914-EX, 914-DX, and 914-AX, are all accessed via the 914-HDE diagnostics connection. Figure 5-9: Diagnostic GUI Start Screen Figure 5-10: 914-HDE Stack View Focal Technologies Corporation Page 5-4 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 41: Figure 5-11: Changing The Board Type

    Section 14.0. Users should always be aware of the Hardware Connection LED’s status, as it is the main indicator for the state of communications with the console HDE. Focal Technologies Corporation Page 5-5 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 42: Figure 5-13: Example 914-X System

    Figure 5-13, with its GUI counterpart shown in Figure 5-14. Figure 5-13: Example 914-X System Figure 5-14: 914-HDE Stack View for Example System Focal Technologies Corporation Page 5-6 A Moog Inc. Company...
  • Page 43: 914-Hde Diagnostic Header

    The GUI preserves the state of the debug communications selection between uses. Figure 5-17: Debug Communications Selection Focal Technologies Corporation Page 5-7 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 44: 914-Hde Stack View

    Additionally, warning messages (enclosed by a red border) can display below the optical table, outlining potential hardware or software problems. More information on these warnings and how to fix them can be found in Section 5.3.1. Figure 5-19: Optical Stack Details Focal Technologies Corporation Page 5-8 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 45: Figure 5-20: Far Side Stack Details

    Optical and Hardware Connection LEDs on the header are green; and each expansion slot matches on the near and far sides (verify that the prefixes of each expansion are the expected card and slot values). Focal Technologies Corporation Page 5-9 A Moog Inc. Company...
  • Page 46: Stack View Error Messages

    The GUI has identified a DX card on the stack. However, the expansion slot this DX card populates is configured as an AX on the HDE. To fix this, refer to Section 6.3.7. Figure 5-22: AX Warning Message Focal Technologies Corporation Page 5-10 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 47: Losing Optical Uplink

    Refer to item #6 in Section 14.0 for ways to reestablish uplink. Figure 5-25: Uplink Loss Example Focal Technologies Corporation Page 5-11 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 48: 914-Hde Status Page

    Red LEDs indicate potential problems that need to be addressed and yellow LEDs give warnings. Low and high limits clarify the value at which the LEDs will turn red. Figure 5-28: 914-HDE Voltage and Junction Temperature Information Focal Technologies Corporation Page 5-12 A Moog Inc. Company...
  • Page 49: Figure 5-29: 914-Hde Optical Information

    Figure 5-32 shows the status of each of the low-speed expansions and LED headers. Headers configured as input will remain inactive. Figure 5-32: Low Speed Expansion and LED Header Information Focal Technologies Corporation Page 5-13 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 50: Figure 5-33: Alternative Led Header Display With Fos

    Pressing “Modify HDE Settings” will bring the user to the HDE settings page (see Section 5.5). The remaining options reset all statistics stored in the near and far HDE (link loss counts, for example) respectively. Figure 5-35: 914-HDE Sub-Header Focal Technologies Corporation Page 5-14 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 51: 914-Hde Settings Page

    “HDE”. Figure 5-36: 914-HDE Diagnostic Status Selection Select the “Modify HDE Settings” option to open the HDE settings page. Figure 5-37: 914-HDE Diagnostic Settings Selection Focal Technologies Corporation Page 5-15 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 52: Figure 5-38: 914-Hde Settings Page

    HDE's status page. To the right of this button is the loading icon, which only appears when the page is loading and when settings are being saved. The page is disabled while settings are being saved. Figure 5-40: 914-HDE Settings Page Sub-Header Focal Technologies Corporation Page 5-16 A Moog Inc. Company...
  • Page 53: 914-Hde General Configuration

    0. These settings are non-volatile and do not need to be reconfigured each time the 914-HDE is powered. Once the desired settings are selected, press “Save” and confirm to apply them to the board. Figure 5-44: 914-HDE Video Configuration Focal Technologies Corporation Page 5-17 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 54: 914-Hde Serial Configuration

    The option to “Trade HD for GbE” is only available for L1 cards (see Section 5.5). Once the desired settings are selected, press “Save” and confirm to apply them to the board. Figure 5-46: 914-HDE Ethernet Configuration Focal Technologies Corporation Page 5-18 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 55: 914-Hde Low Speed Expansion Configuration

    914-HDE is powered. Once the desired settings are selected, press “Save” and confirm to apply them to the board. Figure 5-48: 914-HDE Low Speed Expansion Configuration Focal Technologies Corporation Page 5-19 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 56: 914-Hde Optical Page

    The reset statistics options clear all statistical data stored in the near and far HDE (link loss counts, for example) respectively. Figure 5-51: 914-HDE Optical Sub-Header Focal Technologies Corporation Page 5-20 A Moog Inc. Company...
  • Page 57: 914-Hde Engineering Status Page

    Details on this EX-specific table can be found in Section 6.2.7. Figure 5-53: 914-HDE Engineering Page Generic card information can be found in the Card Info (HDE) section. Figure 5-54: 914-HDE Additional Card Information Focal Technologies Corporation Page 5-21 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 58: Figure 5-55: 914-Hde Serial, Ethernet, And Video Statistic Information

    Section 5.8). The remaining options reset all statistics stored in the near and far HDE (link loss counts, for example) respectively. Figure 5-56: 914-HDE Engineering Sub-Header Focal Technologies Corporation Page 5-22 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 59: 914-Hde Engineering Settings Page

    “Engineering” button on the header. Figure 5-57: 914-HDE Engineering Status Selection Select the “Modify Settings” option to open the Engineering settings page. Figure 5-58: 914-HDE Engineering Settings Selection Focal Technologies Corporation Page 5-23 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 60: Figure 5-59: 914-Hde Engineering Settings Page

    Engineering page. To the right of this button is the loading icon, which only appears when the page is loading and when settings are being saved. The page is disabled while settings are being saved. Figure 5-60: 914-HDE Engineering Settings Page Sub-Header Focal Technologies Corporation Page 5-24 A Moog Inc. Company...
  • Page 61: 914-Hde General Engineering Configuration Settings

    Once the desired cards have been locked or unlocked, press “Save” and confirm to apply the changes to each board. Figure 5-63: 914-X Series Lock Configurations Focal Technologies Corporation Page 5-25 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 62: 914-Hde Video Test Pattern Generation Settings

    These settings are non-volatile and do not need to be reconfigured each time the 914-HDE is powered. Once the desired settings are selected, press “Save” and confirm to apply them to the board. Figure 5-64: 914-HDE Video Generation Configurations Focal Technologies Corporation Page 5-26 A Moog Inc. Company...
  • Page 63: 914-X Series Advanced Page

    Figure 5-65: 914-HDE Advanced Selection Figure 5-66: 914-HDE Advanced Page The stack view can be returned to at any time by pressing “Back” on the subheader or “Stack” on the header. Focal Technologies Corporation Page 5-27 A Moog Inc. Company...
  • Page 64: System-Level Configurations

    (JavaScript Object Notation) file. Then, it will scan the stack connected to the COM port and save all board settings into the file. To ensure configuration data does not get corrupted, these files should not be modified without contacting Moog Focal first.
  • Page 65: Figure 5-70: Configuration Example Stack

    Detailed information on the severity and outcomes of various stack inconsistencies, as well as other potential issues that may arise during configurations, are provided in the sections below. Focal Technologies Corporation Page 5-29 A Moog Inc. Company...
  • Page 66: Troubleshooting Other Errors

    No Valid Data Found The syntax of the JSON file was updated and/or invalid. Ensure that the most recent version of the GUI is installed. If problems persist, Contact Moog Focal with the file attached or create a new configuration file. 5.9.1.1.2 Invalid Character Found A non-hexadecimal character has been identified in the configuration file.
  • Page 67 Section 6.1.9 for the VDX), and the configuration file uses TTL. If the user decides to continue, the serial channels configured as TTL will be configured as RS-485 instead. Focal Technologies Corporation Page 5-31 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 68: 914-Hde Data Snapshots

    A system snapshot captures the status and settings of the attached stack at the moment it is taken. should always be included in customer support emails to Moog Focal, as they significantly simplify the troubleshooting process. To take a snapshot, users can navigate to the Advanced page and select the “Save System Snapshot” option. This will prompt the user to either create a new JSON file or use an existing one.
  • Page 69: Figure 5-75: Exit Offline Mode Option

    Additionally, if a custom error message is displayed indicating a problem, it is likely due to a modified or corrupted snapshot file. Focal Technologies Corporation Page 5-33 A Moog Inc.
  • Page 70: Reading And Writing I

    C table on the right will then refresh with the specified page’s updated information. Using the I C write feature should only be done with expert advice from Moog Focal. These writes could corrupt a system configuration. Figure 5-77: 914-HDE I C Write Result Before attempting a write operation, all cards on the stack should be unlocked.
  • Page 71: Restarting The Gui

    5. Open the 914-X Series Unified Diagnostic GUI. Reconnect to the COM port (see Section 5.1.1) and allow up to twenty seconds for the 914-X system to connect. Focal Technologies Corporation Page 5-35 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 72: Updating Versions Of The Diagnostic Gui

    Updating Versions of the Diagnostic GUI The 914-X Unified Diagnostic GUI is maintained by Moog Focal, with new versions of the software released as necessary. The current software version is displayed the top left corner of the screen, within the box highlighted in red in the image below.
  • Page 73: 914-X Series Expansion Cards

    The expansion connector provides for 21/32” (16.67 mm) spacing between cards when directly stacked together. For tight spaces and/or larger stacks, Moog Focal can provide high speed ribbon cables to allow cards to sit up to 18” (46 cm) apart. Please refer to Section 10.3...
  • Page 74: 914-Vdx Serial Data Ports

    Use only one of the RS232-TX pins, not both. Isolated ground is shared between the ports Figure 6-2: 914-VDX Molex Micro-fit, P/N 43045-0800 Figure 6-3: 914-VDX Serial Ports Focal Technologies Corporation Page 6-38 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 75: 914-Vdx Composite Video Channels

    Video latency through the Mux/Demux system is less than 25 µs, not including fiber delays of 5 s/m. Figure 6-4: 914-VDX Mini SMB Jack - Amphenol P/N 142146-75 Figure 6-5: 914-VDX Video Connector Locations Focal Technologies Corporation Page 6-39 A Moog Inc. Company...
  • Page 76: 914-Vdx Power

    The onboard surface mount fuse, F1, is rated to 2A and is not intended to be field replaceable. If the power fuse is blown, the card should be evaluated for damage by the factory or trained service personnel prior to any repair. Focal Technologies Corporation Page 6-40 A Moog Inc.
  • Page 77: 914-Vdx Diagnostic Leds

    Flashing LED indicates serial Channel 2 is transmitting to external equipment. Yellow Flashing LED indicates serial Channel 2 is receiving from external equipment. Figure 6-7: 914-VDX Diagnostic LED Locations Focal Technologies Corporation Page 6-41 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 78: 914-Vdx Diagnostic Led Header

    SER CH4 ACT Flashing LED indicates serial Channel 4 activity. Active low. Ground, non-isolated, connected to 914-HDE input voltage ground. Figure 6-8: 914-VDX Diagnostic LED Header Focal Technologies Corporation Page 6-42 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 79: 914-Vdx Expansion Channel Configuration

    MS Expansion Channel 1 MS Expansion Channel 2 MS Expansion Channel 3 MS Expansion Channel 4 Figure 6-9: 914-VDX Diagnostic LED Header Figure 6-10: 914-VDX SW1 Position and Orientation Focal Technologies Corporation Page 6-43 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 80: 914-Vdx Status Page

    Figure 6-12: 914-VDX Status Page Overview Generic card information (such as the serial number or hardware revision) can be found in the Card Details table. Figure 6-13: 914-VDX Card Information Focal Technologies Corporation Page 6-44 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 81: Figure 6-14: 914-Vdx Voltage And Junction Temperature Information

    Pressing “Modify VDX Settings” will bring the user to the VDX settings page (see Section 6.1.8). The remaining options reset all statistics stored in the near and far VDX (link loss counts, for example) respectively. Figure 6-18: 914-VDX Sub-Header Focal Technologies Corporation Page 6-45 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 82: 914-Vdx Settings Page

    Figure 6-19: 914-VDX Diagnostic Status Selection Select the “Modify VDX Settings” option to open the VDX settings page. Figure 6-20: 914-VDX Diagnostic Settings Selection Figure 6-21: 914-VDX Settings Page Focal Technologies Corporation Page 6-46 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 83: Figure 6-22: 914-Vdx Data Field Types

    VDX cards. If proposed changes are not being applied when saving, refer to item #4 in Section 14.0. Figure 6-24: 914-VDX Unsaved Settings Focal Technologies Corporation Page 6-47 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 84: Figure 6-25: 914-Vdx Card Mode Configuration

    • RS232: No options • TTL: No options (not supported for legacy revisions of the VDX; refer to Section 6.1.9) • Figure 6-28: 914-VDX Serial Configuration Focal Technologies Corporation Page 6-48 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 85: Legacy 914-Vdx Information (Board Rev. 3 And Earlier)

    REV 4 AND LATER ISO GND Table 6-10: Legacy 914-VDX Mating Connectors DESIGNATOR DESCRIPTION MFR. PART NUMBER / FOCAL PN CRIMP PINS / FOCAL PN J7 (≤ Board Rev 2) Diagnostics (Old revs) Molex 0781720003 / EL-J0579 0781720410 / EL-J0580 J7 (≥...
  • Page 86: Table 6-12: Legacy 914-Vdx Diagnostic Leds

    Flashing LED indicates serial Channel 2 is transmitting to external equipment. Yellow Flashing LED indicates serial Channel 2 is receiving from external equipment. Figure 6-30: 914-VDX Diagnostic LED Locations (Board Revisions 3 and Earlier) Focal Technologies Corporation Page 6-50 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 87: Figure 6-31: 914-Ex

    Ethernet traffic. Actual bandwidth requirements are based on the external devices connected to the Ethernet ports. Ensure there is enough available bandwidth when using either single or dual expansion modes. Figure 6-31: 914-EX Focal Technologies Corporation Page 6-51 A Moog Inc. Company...
  • Page 88: 914-Ex Ethernet Ports

    # Bytes * 0.008 µs OL (Optical Latency) 5 µs / km 5 µs / km 5 µs / km Latency = FEL + FT + OL Focal Technologies Corporation Page 6-52 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 89: 914-Ex Ethernet Rj45 Leds

    GREEN/ORANGE YELLOW 10 BASE-T ORANGE 100 BASE-TX GREEN 1000 BASE-T LINKED FLASHING LINKED WITH ACTIVITY Speed indication only valid when link LED is on or flashing. Focal Technologies Corporation Page 6-53 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 90: 914-Ex Power

    The onboard surface mount fuse, F1, is rated to 2A and is not intended to be field replaceable. If the power fuse is blown, the card should be evaluated for damage by the factory or trained service personnel prior to any repair. Focal Technologies Corporation Page 6-54 A Moog Inc.
  • Page 91: 914-Ex Diagnostic Leds

    Secondary Expansion channel fault. No link established to partner card via 914-HDE across the optical link. Green Secondary Expansion channel link. Valid link established to partner card via 914-HDE across the optical link. Figure 6-34: 914-EX Diagnostic LED Locations Focal Technologies Corporation Page 6-55 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 92: 914-Ex Diagnostic Led Header

    Activity present on Ethernet Port 2. Active low. ETHERNET PORT 2 LINK Ethernet Port 2 is linked. Active low. Ground, non-isolated, connected to 914-HDE input voltage ground. Figure 6-35: 914-EX Diagnostic LED Header Focal Technologies Corporation Page 6-56 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 93: 914-Ex Expansion Channel Configuration

    MS Expansion Channel 1 MS Expansion Channel 2 MS Expansion Channel 3 MS Expansion Channel 4 Figure 6-36: 914-EX Diagnostic LED Header Figure 6-37: 914-EX SW1 Position and Orientation Focal Technologies Corporation Page 6-57 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 94: 914-Ex Status Page

    Figure 6-39: 914-EX Status Page Overview Generic card information (such as the serial number or hardware revision) can be found in the Card Details table. Figure 6-40: 914-EX Card Information Focal Technologies Corporation Page 6-58 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 95: Figure 6-41: 914-Ex Voltage And Junction Temperature Information

    Additional EX Ethernet Statistic information for attached cards can be found at the bottom of the Engineering page (see Section 5.7). This table only displays if at least one EX card pair is connected to the stack. Figure 6-46: 914-EX Engineering Statistic Information Focal Technologies Corporation Page 6-59 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 96: 914-Ex Settings Page

    Figure 6-47: 914-EX Diagnostic Status Selection Select the “Modify EX Settings” option to open the EX settings page. Figure 6-48: 914-EX Diagnostic Settings Selection Figure 6-49: 914-EX Settings Page Focal Technologies Corporation Page 6-60 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 97: Figure 6-50: 914-Ex Data Field Types

    EX cards. If proposed changes are not being applied when saving, refer to item #4 in Section 14.0. Figure 6-52: 914-EX Unsaved Settings Focal Technologies Corporation Page 6-61 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 98: Figure 6-53: 914-Ex Card Mode Configuration

    Enabling Remote Link Speed Sync at the console prevents the user from modifying the locally advertised link and master/slave settings. Once the desired settings are selected, press “Save” and confirm to apply them to the board. Figure 6-55: 914-EX Ethernet Configuration Focal Technologies Corporation Page 6-62 A Moog Inc. Company...
  • Page 99: Figure 6-56: 914-Ex Forced Ethernet Configuration

    Once the desired settings are selected, press “Save” and confirm to apply them to the board. Figure 6-56: 914-EX Forced Ethernet Configuration Focal Technologies Corporation Page 6-63 A Moog Inc. Company...
  • Page 100: Legacy 914-Ex Information (Board Rev. 4 And Earlier)

    REV 5 AND LATER ISO GND Table 6-20: Legacy 914-EX Mating Connectors DESIGNATOR DESCRIPTION MFR. PART NUMBER / FOCAL PN CRIMP PINS / FOCAL PN J4 (≤ Board Rev 2) Diagnostics (Old revs) Molex 0781720003 / EL-J0579 0781720410 / EL-J0580 J4 (≥...
  • Page 101: 914-Ax Aib Module Options

    ARCNET Sonar Module 903-0252-00 903-0252-00 903-0252-01 903-0251-00 903-0244-00 903-0261-00 903-0250-00 903-0297-00 Part Number Please refer to 700-0271-00 AIB Plug-in Module User Manual for details and configurations. Focal Technologies Corporation Page 6-65 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 102: 914-Ax Aib Module Installation

    When installing an AIB module onto the 914-AX across connectors J5 and J6, ensure the white dots on both the AIB module and the 914-AX line up for proper orientation. Figure 6-60: AIB Module Orientation Focal Technologies Corporation Page 6-66 A Moog Inc. Company...
  • Page 103: 914-Ax Interface Connector

    20-28 AWG stranded conductors with 0.22” - 0.24” stripped ends. The clamp for each pin can be opened by inserting either a WAGO tool or a small screwdriver in the hole immediately above the wire hole. Figure 6-62: 914-AX WAGO Connector Mating Plug Focal Technologies Corporation Page 6-67 A Moog Inc. Company...
  • Page 104: 914-Ax Diagnostic Leds

    AIB TX data. TX refers to transmit from the 914-AX. Yellow AIB RX data. RX refers to receive at the 914-AX. Figure 6-63: 914-AX Diagnostic LEDs Focal Technologies Corporation Page 6-68 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 105: 914-Ax Diagnostic Led Header

    AIB RX DATA Data is received at the AIB module. Active low. Ground, non-isolated, connected to 914-HDE input voltage ground. Figure 6-64: 914-AX Diagnostic LED Header Focal Technologies Corporation Page 6-69 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 106: 914-Ax Configuration And Diagnostics

    5.1.4). The low speed expansion channel which the AX is attached to must be configured as an AX; for instructions, see Section 5.5.5. Figure 6-65: 914-AX Configuration Setup Figure 6-66: 914-AX Data Activity Focal Technologies Corporation Page 6-70 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 107: Figure 6-67: 914-Dx

    914-DX within the Diagnostic GUI prior to operation. The maximum baud rate of each channel must not exceed 250 kbaud for reliable communication. Figure 6-67: 914-DX Focal Technologies Corporation Page 6-71 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 108: 914-Dx Serial Data Ports

    µs This is the latency added by the 914-DX, which must be combined with the latency of the 914-HDE serial data and fiber optic delays to give a total latency value. Focal Technologies Corporation Page 6-72 A Moog Inc. Company...
  • Page 109: 914-Dx Power

    The onboard surface mount fuse, F1, is rated to 2A and is not intended to be field replaceable. If the power fuse is blown, the card should be evaluated for damage by the factory or trained service personnel prior to any repair. Focal Technologies Corporation Page 6-73 A Moog Inc.
  • Page 110: 914-Dx Diagnostic Leds

    Serial Channel 4 RX Activity GREEN Serial Channel 5 TX Activity YELLOW Serial Channel 5 RX Activity GREEN Serial Channel 6 TX Activity YELLOW Serial Channel 6 RX Activity Focal Technologies Corporation Page 6-74 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 111: 914-Dx Diagnostic Led Header

    Expansion channel fault. No link established to partner card via 914-HDE across the EXPANSION FAULT optical link. Active low. Ground, non-isolated, connected to 914-HDE input voltage ground. Figure 6-74: 914-DX Diagnostic LED Header Focal Technologies Corporation Page 6-75 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 112: 914-Dx Expansion Channel Configuration

    LS Expansion Channel 2 LS Expansion Channel 3 LS Expansion Channel 4 Figure 6-75: 914-DX Expansion Channel Configuration Switch SW1 Figure 6-76: 914-DX SW1 Position and Orientation Focal Technologies Corporation Page 6-76 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 113: 914-Dx Status Page

    Figure 6-78: 914-DX Status Page Overview Generic card information (such as the serial number or hardware revision) can be found in the Card Details table. Figure 6-79: 914-DX Card Information Focal Technologies Corporation Page 6-77 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 114: Figure 6-80: 914-Dx Voltage Information

    #1. The “Back” button returns the user to the stack view. Pressing “Modify DX Settings” will bring the user to the DX settings page (see Section 6.4.7). Figure 6-84: 914-DX Sub-Header Focal Technologies Corporation Page 6-78 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 115: 914-Dx Settings Page

    Figure 6-85: 914-DX Diagnostic Status Selection Select the “Modify DX Settings” option to open the DX settings page. Figure 6-86: 914-DX Diagnostic Settings Selection Figure 6-87: 914-DX Settings Page Focal Technologies Corporation Page 6-79 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 116: Figure 6-88: 914-Dx Data Field Types

    DX cards. If proposed changes are not being applied when saving, refer to item #4 in Section 14.0. Figure 6-90: 914-DX Unsaved Settings Focal Technologies Corporation Page 6-80 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 117: Figure 6-91: 914-Dx Card Mode Configuration

    Section 6.4.1): RS485: 1 ms timeout; terminations enabled • RS422: Terminations enabled • RS232: No options • • TTL: No options Figure 6-93: 914-DX Serial Configuration Focal Technologies Corporation Page 6-81 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 118: Legacy 914-Dx Information (Board Rev. 3.3 And Earlier)

    REV 4 AND LATER ISO GND Table 6-32: Legacy 914-DX Mating Connectors DESIGNATOR DESCRIPTION MFR. PART NUMBER / FOCAL PN CRIMP PINS / FOCAL PN J7 (≤ Board Rev 2) Diagnostics (Old revs) Molex 0781720003 / EL-J0579 0781720410 / EL-J0580 J7 (≥...
  • Page 119: 914 Media Converters

    Config. Dwg 914-2018-00 The Moog Focal Model 914-HDV2 is a standalone media converter solution for one or two 3G/HD/SD-SDI video feeds per card. This card has the same form factor and mounting requirements as the rest of the 914-X Series, and can have the optical signals combined with a 914-HDE system via available optical CWDM cards.
  • Page 120: Figure 7-2: 914-Hdv2 Interface Locations

    Model 914-X Series Modular Multiplexer System User Manual Figure 7-2: 914-HDV2 Interface Locations Figure 7-3: 914-HDV2 J4 Optical Transceiver Directions Figure 7-4: 914-HDV2 J6 Diagnostic Connector Focal Technologies Corporation Page 7-2 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 121: 914-Hdv2 Video Connections

    All versions of the 914-HDV2 use high powered optical transceivers, a minimum link loss or attenuation of 10 dB is suggested. Bushings on the SFP optical transceiver are standard LC. Fiber type is single mode. Figure 7-7: 914-HDV2 Optical Interface Focal Technologies Corporation Page 7-3 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 122: 914-Hdv2 Power

    914-HDV2. There are hardware differences between the MSA and non-MSA boards; do not alter the switch settings without consulting Moog Focal. The exceptions are SW2 and SW6, EQ and CD settings. This can be tuned to the video resolution and cable lengths as required.
  • Page 123: 914-Hdv2 Diagnostic Leds

    Video Channel 2 output valid (console) Green Power Fault. Outside of +4.5 V to +13.0 V range. Power Good Green Figure 7-10: 914-HDV2 Diagnostic LED Locations Focal Technologies Corporation Page 7-5 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 124: 914-Hdv2 Diagnostic Led Header

    Video Channel 1 output is valid. Console only. Active low. VID CH2 VALID Video Channel 2 output is valid. Console only. Active low. Ground Figure 7-11: 914-HDV2 J7 LED Header Focal Technologies Corporation Page 7-6 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 125: 914-Hdv2 Diagnostics

    Connecting 914-HDV2 Hardware to the GUI Once installed, open the software and select the 914-HDV2 tile. Figure 7-12: Diagnostic GUI HDV2 Selection Figure 7-13: 914-HDV2 Main View Focal Technologies Corporation Page 7-7 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 126: Figure 7-14: Changing The Board Type

    They should blink regularly, which indicates that healthy communication is taking place between the serial port and the console 914-HDV2. Figure 7-17: Header Send and Receive LEDs Focal Technologies Corporation Page 7-8 A Moog Inc. Company...
  • Page 127: Table 7-7: 914-Hdv2 Configuration-Specific Diagnostics

    Figure 7-18: 914-HDV2 Main View Example If nothing displays (the screen appears like Figure 7-13), refer to item #2 in Section 14.0. Focal Technologies Corporation Page 7-9 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 128: Figure 7-19: Hde On Hdv2 Screen Warning Message

    The card connected to the diagnostic port is likely not an HDE. This occurs when loading onto the HDV2 screen while connected to an HDE card. Figure 7-19: HDE on HDV2 Screen Warning Message Focal Technologies Corporation Page 7-10 A Moog Inc. Company...
  • Page 129: Figure 7-20: 914-Hdv2 Card Information

    Figure 7-23 shows the switch configuration table, which depicts the current dip switch positions on the linked HDV2. Figure 7-23: 914-HDV2 Switch Information Figure 7-24 shows the current state of the board's diagnostic LED headers. Figure 7-24: 914-HDV2 LED Information Focal Technologies Corporation Page 7-11 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 130: Figure 7-25: 914-Hdv2 General Sfp Information

    Figure 7-26: 914-HDV2 Analog SFP Information Figure 7-27 illustrates the optical link table, which displays the status of the fiber optic connection(s). Figure 7-27: 914-HDV2 Optical Link Information Focal Technologies Corporation Page 7-12 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 131: Figure 7-28: 914-Hdv2 Advanced Page Selection

    The main view can be returned to at any time by pressing “Back” on the subheader or “Main View” on the header. Engineering information is displayed below the I C table in the “Factory Status” table. Figure 7-30: 914-HDV2 Factory Status Information Focal Technologies Corporation Page 7-13 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 132: Figure 7-31: Save System Snapshot Option

    A system snapshot captures the status of the attached HDV2 at the moment it is taken. Data Snapshots should always be included in customer support emails to Focal, as they significantly simplify troubleshooting. To take a snapshot, users can navigate to the Advanced page and select the “Save System Snapshot” option. This will prompt the user to either create a new JSON file or use an existing one.
  • Page 133: Figure 7-34: Exit Offline Mode Option

    C page and select Read. The requested data will then populate the I C table on the right side of the screen. Figure 7-35: 914-HDV2 Read Result Focal Technologies Corporation Page 7-15 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 134: Legacy 914-Hdv2 Information (Board Rev. 3.3 And Earlier)

    REV 4 AND LATER ISO GND Table 7-9: Legacy 914-HDV2 Mating Connectors DESIGNATOR DESCRIPTION MFR. PART NUMBER / FOCAL PN CRIMP PINS / FOCAL PN J7 (≤ Board Rev 3.3) Diagnostics (Old revs) Molex 0781720003 / EL-J0579 0781720410 / EL-J0580 J7 (≥...
  • Page 135: Other 914 Cards

    The standard 1471 nm and 1491 nm CWDM wavelengths used on the 914-CWDM optics card can be changed to other wavelengths upon request, but only the 1471/1491 nm version can be daisy chained with existing 1310/1550 nm systems. Focal Technologies Corporation Page 8-1 A Moog Inc. Company...
  • Page 136: 914-Cwdm-4R1

    CWDM cards at both ends of the system. Table 8-1: 914-CWDM-4R1 Wavelength Allocations LC CONN. WAVELENGTH 1471 nm 1491 nm 1511 nm 1531 nm Figure 8-3: 914-CWDM-4R1, 4-Channel CWDM Optics Card, Assembly 914-2017-11 Focal Technologies Corporation Page 8-2 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 137: Figure 8-4: 914-Cwdm-4R1, 4-Channel Cwdm Optics Card With Bypass, Assembly 914-2017-17

    Model 914-X Series Modular Multiplexer System User Manual Figure 8-4: 914-CWDM-4R1, 4-Channel CWDM Optics Card with Bypass, Assembly 914-2017-17 Focal Technologies Corporation Page 8-3 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 138: 914-Cwdm-8R

    Table 8-2: 914-CWDM-8R LC Bushing Wavelengths 1471 nm 1491 nm 1511 nm 1531 nm 1551 nm 1571 nm 1591 nm 1611 nm Figure 8-5: 914-CWDM-8R, 8-Channel CWDM Optics Card, Assembly 914-0017-16 Focal Technologies Corporation Page 8-4 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 139: Figure 8-6: 914-Cwdm-8R, 8-Channel Cwdm Optics Card, Assembly 914-0017-20

    Model 914-X Series Modular Multiplexer System User Manual Figure 8-6: 914-CWDM-8R, 8-Channel CWDM Optics Card, Assembly 914-0017-20 Figure 8-7: 914-CWDM-8R, 8-Channel CWDM Optics Card, Assembly 914-0017-21 Focal Technologies Corporation Page 8-5 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 140: 914-Fos

    Ensure that the onboard switch SW1 is in position 3 for both modes. Figure 8-8: 914-FOS, Fiber Optic Switch Card Figure 8-9: 914-FOS J1 Pinout (External Switch Figure 8-10: 914-FOS J2 (HDE Input), J3 (LED Connector) Output) Pinout Focal Technologies Corporation Page 8-6 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 141: Figure 8-11: 914-Fos Gui Enable

    Override: Allows forcing the fiber optic routing onto a specific fiber, as specified on the rightmost side of the FOS Mode row. Figure 8-12: 914-FOS Configuration Options Focal Technologies Corporation Page 8-7 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 142: 914-Split

    Figure 8-13: 914-SPLIT, 1x2 Optical Splitter Card Focal Technologies Corporation Page 8-8 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 143: System Cards

    The input voltage is filtered by both ‘pi’ and differential type filters to reduce input noise. Isolation is between input and output. Efficiency rating is at full load. Focal Technologies Corporation Page 8-9 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 144: 914-Dc-12

    The input voltage is filtered by both ‘pi’ and differential type filters to reduce input noise. Isolation is between input and output. Efficiency rating is at full load. Focal Technologies Corporation Page 8-10 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 145: Moog Focal Optical Transceivers

    Model 914-X Series Modular Multiplexer System User Manual Moog Focal Optical Transceivers Moog Focal OEM SFP optical transceivers are available for sparing, replacements, and upgrades. Pressure tolerant versions of the 4.25 Gbps SFPs are available. Table 9-1: SFP Optical Transceiver Options 4.25 Gbps...
  • Page 146: 10.0 914-X Series System Installation And Operation

    LC connectors in the transceiver bushings using MIL-A-46146 equivalent RTV, such as Dow Corning 3145 clear RTV. RTV may also be applied to power and data connectors, if required. Focal Technologies Corporation Page 10-1 A Moog Inc. Company...
  • Page 147: Card Stacking

    Start the new stack with supplied 21/32” standoffs. C. Repeat step 4 for each Expansion card. 5. Complete the stack with supplied nuts and Loctite 290 (or similar) to retain the top card. Focal Technologies Corporation Page 10-2 A Moog Inc. Company...
  • Page 148: 914-X Series Expansion Interface Ribbon Cables

    When specifying a large stack to fit into a small enclosure or pressure bottle, it may be desirable to break the stack into smaller pieces. This can be accomplished with Moog Focal 914-X Series expansion interface high speed ribbon cables. Specify lengths from 3” to 18” with orientations for inline mounting vs side-to-side mounting.
  • Page 149: Figure 10-5: 914-X Series System Dual Stack (Side-To-Side) Layout

    Model 914-X Series Modular Multiplexer System User Manual Figure 10-5: 914-X Series System Dual Stack (side-to-side) Layout Many other configurations are possible, these are representative examples. Focal Technologies Corporation Page 10-4 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 150: 914-X Series Bench Test

    A spool of fiber used with the VOAT can also be used to simulate dispersion effects over long cable lengths. 5. Repeat steps 1-4 with connections reversed to verify the remote to console (uplink) optical budget. Focal Technologies Corporation Page 10-5 A Moog Inc. Company...
  • Page 151: 914-X Series Electrical And Environmental Specifications

    914-AX power is highly dependent on the AIB module installed. Input amperage must not exceed 4A, if close to 20W is required, the power supply must use a higher nominal voltage e.g. 12V. Focal Technologies Corporation Page 10-6 A Moog Inc. Company...
  • Page 152: 914-X Series Maintenance

    NEVER look into the end of a fiber when it is plugged into a transceiver or active fiber, especially when using a magnifying instrument, such as a fiber microscope. Focal Technologies Corporation Page 10-7 A Moog Inc. Company...
  • Page 153: 914-X Series System Product Handling

    Any visible damage or evidence of loose parts requires removal of the multiplexer from operation and • investigation by qualified service personnel. Focal Technologies Corporation Page 10-8 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 154: 914-X Series Accessories

    Model 914-X Series Modular Multiplexer System User Manual 10.8 914-X Series Accessories Model 914 accessory kits are available from Moog Focal, these include mating cables for all interfaces. Please contact your local Moog Focal representative for more information including orderable part numbers. 10.9 914-X Series Dimensions 10.9.1...
  • Page 155: 914-Ex

    Model 914-X Series Modular Multiplexer System User Manual 10.9.3 914-EX. Figure 10-11: 914-EX Dimensions (inches [mm]) 10.9.4 914-AX. Figure 10-12: 914-AX Dimensions (inches [mm]) Focal Technologies Corporation Page 10-10 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 156: 914-Dx

    Model 914-X Series Modular Multiplexer System User Manual 10.9.5 914-DX Figure 10-13: 914-DX Dimensions (inches [mm]) 10.9.6 914-HDV2 Figure 10-14: 914-HDV2 Dimensions (inches [mm]) Focal Technologies Corporation Page 10-11 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 157: 10.10 Connector Part Numbers

    HDV2 20021521- 20021444-00010T1LF 00010T1LF [plug compatible with most 10 wire 0.05“ spacing Header [10-pin; 2 row] ribbon cables] 501953-0305 015133-0306 Diagnostics Molex [3-pin picoclasp] [3-pin plug] Focal Technologies Corporation Page 10-12 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 158: 10.11 Signal Specifications

    Minimum latency is for 1000 BASE-T, typical for 100 BASE-TX, and maximum for 10 BASE-T. Does not include latency through the AIB plug-in modules. Specifications for the AIB plugin modules are contained in the 700-0271-00 user manual. Focal Technologies Corporation Page 10-13 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 159: 11.0 Firmware Updates

    8. Select the Model # to be updated (914_HDE or 914_Expansion for the VDX/EX/DX). 9. Select “Clear Flash”. 10. Select “FPGA”. 11. Click “Select FW File” and select the firmware *.bin file provided by Moog Focal. 12. Press “Start FW Update”. 13. Power ON the 914 card.
  • Page 160: Firmware Compatibility

    Table 11-1 shows compatible revisions in rows. Ideally cards should be updated to a “Current Revision” for cross compatibility with other cards. Old revision firmware is not compatible with current revision firmware. Please contact Moog Focal for more information and the files required to update older systems. Table 11-1: Firmware Revisions...
  • Page 161: 12.0 Feature Upgrades

    1. There are two codes required for the feature upgrade to take place: a Feature Code and an Unlock Code. Obtain these 16-digit hexadecimal alphanumeric codes from Moog Focal. 2. Open the 914-X Series Unified Diagnostic GUI with the Console 914-HDE connected to a local COM port,...
  • Page 162: 13.0 Part Numbers

    Table 13-2: 914-HDE Included Accessories QUANTITY DESCRIPTION Power harness, 6’, pigtailed RS232 Diagnostic cable, 6”, pigtailed #2-56, 3/16”, 21/32” tall standoff #2-56, 3/16”, 5/32” tall standoff #2-56, hex nut Focal Technologies Corporation Page 13-1 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 163: Table 13-3: 914-Hde Cwdm Options

    Red wavelengths are recommended, particularly 1471 to 1571 nm. • 1591 and 1611 nm wavelengths are not recommended for use with the Moog Focal Optical Monitoring System (OMS). When configuring a system, it is best to choose adjacent wavelengths and not to mix red band with blue band •...
  • Page 164: Table 13-5: 914-Hde Factory Configurations

    Users may alter all allowable configurations via the Diagnostic GUI. • Default configuration is recommended for spare assemblies. • Other factory settings are possible. Contact Moog Focal for more options. • Configurations other than the default are subject to a surcharge. •...
  • Page 165: 914-Vdx Part Numbers

    Factory configuration options represent “as shipped” settings. • Users may alter all configurations via the Diagnostic GUI in combination with dip switches. • Default configuration is recommended for spare assemblies Focal Technologies Corporation Page 13-4 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 166 MS expansion’s SW1 is configured in line with Section 6.1.6. Other factory settings are possible. Contact Moog Focal for more options. • Configurations other than the default are subject to a surcharge.
  • Page 167: 914-Ex Part Numbers

    MS expansion’s SW1 is configured in ascending order in line with Section 6.2.6. Other factory settings are possible. Contact Moog Focal for more options. • Configurations other than the default are subject to a surcharge. •...
  • Page 168: 914-Ax Part Numbers

    Tritech ARCNET compatible interface 903-0261-01 AIB-ARCNET-P6 Tritech ARCNET compatible interface, pressure tolerant assembly rated to 6000 PSI. 903-0297-00 AIB-CANBUS CAN bus interface, up to 1 Mb/s supported Focal Technologies Corporation Page 13-7 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 169: 914-Dx Part Numbers

    LS expansion’s SW1 is configured in ascending order in line with Section 6.4.5. Other factory settings are possible. Contact Moog Focal for more options. • • Configurations other than the default are subject to a surcharge.
  • Page 170: 914-Hdv2 Part Numbers

    1611 nm optical transmitter Upgrade, not for use with Moog Focal OMS Notes: • Other dual wavelength CWDM options are possible. Contact Moog Focal for details. Focal Technologies Corporation Page 13-9 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 171: 914-X Series Optical Card Part Numbers

    914-FOS Fiber-Optic Switch Card, SM, 914-0017-10 914-FOS 914-FOS-SM-P0F 2X1, Stacking 914-0017-11 914-CWDM-4R1 914-CWDM-SM4+N-R5-P0F 914-CWDM Optics Card, 8-ch, SM, Red band 914-0017-16 914-CWDM-8R 914-CWDM-SM8+N-R7-P0F 914-CWDM Optics Card, 4-ch, SM, Red band Focal Technologies Corporation Page 13-10 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 172: Sfp Optical Transceiver Part Numbers

    10G; TX 1591 nm dual fiber CWDM SFP 925-0024-61 10G; TX 1611 nm dual fiber CWDM SFP Notes: • Refer to Section 9.0 for SFP specification. Focal Technologies Corporation Page 13-11 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 173: Table 13-24: 914 Pressure Tolerant Optical Sfp Part Numbers

    4.25G; TX 1611 nm; dual fiber CWDM SFP; 6000 PSI; LC Conn. Notes: • Pressure tolerant SFPs are special order items. Refer to Section 9.0 for SFP specification. • Focal Technologies Corporation Page 13-12 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 174: 13.10 914-X Series High Speed Ribbon Cable Part Numbers

    The length is measured connector to connector on the ribbon cable, this does not imply card-to-card spacing. • Other lengths are available up to 18”, please contact Moog Focal. • Included accessory hardware allows for the completion of one stack and the start of the next.
  • Page 175: 14.0 Troubleshooting

    Confirm a stable optical link is present (see item #6). A stable optical link is required to configure remote cards. e. Confirm a stable expansion link is present. A stable expansion link is required to configure expansion cards. If problems persist, please contact Moog Focal describing the problem with a system snapshot attached (refer to Section 5.9.2).
  • Page 176: Power Issues

    Ensure video monitors are on and compatible with the video signal type being used. 3G-SDI video can only be used with M1 speed 914-HDEs with no 914-VDX or 914-EX cards attached, and Ethernet limited to 100 Mb/s. Focal Technologies Corporation Page 14-2 A Moog Inc. Company...
  • Page 177: Ethernet Issues

    Consider attaching thermal spreaders to high temperature components. iii. Consider installing thermal gap pads below the 914-HDE motherboard to push heat to the enclosure. Apply airflow to surface systems. Focal Technologies Corporation Page 14-3 A Moog Inc. Company Document Number: 914-0601-00 Rev. 5.7...
  • Page 178 Temperatures iii. Optical power iv. Dropped Ethernet frames v. Optical link problems vi. Expansion link problems Contact Moog Focal (focal@moog.com), describing the problem and attaching a system snapshot (see Section 5.9.2). Focal Technologies Corporation Page 14-4 A Moog Inc. Company...
  • Page 179: Moog Focal Technical Support Contact Information

    Model 914-X Series Modular Multiplexer System User Manual 14.1 Moog Focal Technical Support Contact Information Focal Technologies Corporation A Moog Inc. Company 77 Frazee Ave. Dartmouth, Nova Scotia Canada B3B 1Z4 1-902-468-2263 focal@moog.com https://www.moog.com/focal Focal Technologies Corporation Page 14-5 A Moog Inc. Company...

This manual is also suitable for:

Moog 914-exMoog 914-hde

Table of Contents