Advertisement
Quick Links
Made in CHINA by / Fabriqué en CHINE par / Hergestellt in CHINA von /
Gemaakt in CHINA door / Fabricado en CHINA por / Prodotto in CINA da /
Fabricado na CHINA por / Vyrobené v ČINE od / Vyrobené v ČINE od /
Wyprodukowane w CHINACH przez: Varan Motors
I
mported by / Importé par / Importiert durch / Geïmporteerd door / Importado
por / Importato da / Importado por / Importované spoločnosťou / Dovezeno
společností / Importowane przez:
BCIE SARL
15 rue de Mensdorf,
L‐5380 Uebersyren,
Luxembourg,
+352/26908036
"© 2024 BCIE SARL. All rights reserved."
"© 2024 BCIE SARL. Tous droits réservés."
"© 2024 BCIE SARL. Alle Rechte vorbehalten."
"© 2024 BCIE SARL. Alle rechten voorbehouden."
"© 2024 BCIE SARL. Todos los derechos reservados."
"© 2024 BCIE SARL. Tutti i diritti riservati."
"© 2024 BCIE SARL. Todos os direitos reservados."
"© 2024 BCIE SARL. Všetky práva vyhradené."
"© 2024 BCIE SARL. Všechna práva vyhrazena."
"© 2024 BCIE SARL. Wszelkie prawa zastrzeżone."
Advertisement
Related Manuals for Varan Motors CT312
Summary of Contents for Varan Motors CT312
- Page 1 Made in CHINA by / Fabriqué en CHINE par / Hergestellt in CHINA von / Gemaakt in CHINA door / Fabricado en CHINA por / Prodotto in CINA da / Fabricado na CHINA por / Vyrobené v ČINE od / Vyrobené v ČINE od / Wyprodukowane w CHINACH przez: Varan Motors mported by / Importé par / Importiert durch / Geïmporteerd door / Importado por / Importato da / Importado por / Importované spoločnosťou / Dovezeno společností / Importowane przez: BCIE SARL 15 rue de Mensdorf, L‐5380 Uebersyren, Luxembourg, +352/26908036 "© 2024 BCIE SARL. All rights reserved." "© 2024 BCIE SARL. Tous droits réservés." "© 2024 BCIE SARL. Alle Rechte vorbehalten." "© 2024 BCIE SARL. Alle rechten voorbehouden." "© 2024 BCIE SARL. Todos los derechos reservados." "© 2024 BCIE SARL. Tutti i diritti riservati." "© 2024 BCIE SARL. Todos os direitos reservados." "© 2024 BCIE SARL. Všetky práva vyhradené." "© 2024 BCIE SARL. Všechna práva vyhrazena." "© 2024 BCIE SARL. Wszelkie prawa zastrzeżone." ...
- Page 2 OPERATION MANUAL FOR WELDING MACHINE FOR MMA/CUT/TIG WELDING MACHINE Thank you for your buying our product, for using it correctly, please at first read this manual carefully.
- Page 3 Input Frequency No-Load Input Cutting Output Rated Weight Voltage(V) (HZ) Voltage(V) Capacity(KVA) thickness Current(A) duty (kg) (mm) cycle(%) ≤10 CT312 50/60 10-30 13.0 ≤12 CT416 50/60 20-40 16.0 ≤15 CT520 50/60 20-50 16.0 FOR MMA FUNCTION: Model Input Frequency No-Load...
-
Page 4: Maintenance
NOTES: OPERATION ENVIRONMENT. THE MACHINE CAN PERFORM IN WHERE CONDITIONS ARE DRY WITH A DAMPNESS LEVEL OF MAX 80%. AMBIENT TEMPERATURE IS BETWEEN -10 AND +40 DEGREES CENTIGRADE. AVOID OPERATING MACHINE IN SUNSHINE OR DRIPPINGS. AVOID OPERATING MACHINE WHERE IS POLLUTED WITH HIGH CONCENTRATION OF CONDUCTIVE DUST OR CORROSIVENESS GAS IN THE AIR. - Page 5 PRESSURE IS ADEQUATE TO WELDING MACHINE IN ORDER TO PROTECT LITTLE COMPONENTS. CHECK THE ELECTRICITY CONNECTORS AND MAKE SURE THE CONNECTORS ARE CONNECTED FIRMLY(SPECIALLY CONNECTORS AND INSERTS). TIGHTEN THE RELAXING CONNECTOR, IF COMPONENTS IS OXIDIZED, THESE OXIDE MUST BE GET RID OF AND CONNECT THEM AGAIN.
-
Page 6: Installation
FOR TIG WELDING INSTRUCTION INSTALLATION CONNECT TO GAS SOURCE: MAKE SURE THAT ARGON TUBE IS CONNECTED TO COPPER TIP TIGHTLY. SUPPLY GAS CIRCUIT MUST INCLUDES GAS CYLINDER, ARGON FLOW METER AND GAS TUBES. TUBES MUST BE TIED FIRMLY BY LARYNGEAL HOOP OR SOMETHING ELSE IN ORDER THAT GAS IS LEAKED AND AIR COME INTO. - Page 7 FOR CUTTING INSTRUCTION OPERATION: MAKE SURE THE CHANG-OVER SWITCH IS ON CUTTING POSITION. OPEN THE POWER SWITCH AND POWER SWITCH IS ON, FAN BEGINS TO REVOLVE. OPEN THE VALVE OR SWITCH OF AIR CONTROLLED, ADJUST PRESSURE AND GAS FLOW TO BE ADEQUATE TO RATE STANDARD.
- Page 8 terminal of torch and inter-machine is relaxed. 5. Abnormal indicator is not on, 1. Primary cable of arc-striking transformer is poor contact with power panel, sound of HF arc-striking can not be tighten it again. heard, output exists. 2. Arc-striking tip is oxidized or distance is too long, give a good polish oxide of burner of adjust to be 1mm between burner.
Need help?
Do you have a question about the CT312 and is the answer not in the manual?
Questions and answers